Renesas TBP-112の取扱説明書

22ページ 0.47 mb
ダウンロード

ページに移動 of 22

Summary
  • Renesas TBP-112 - page 1

    H8S/2214 Series TBP-112 User System Interface Cable (HS2214ECB61H) for E6000 Emulator User’s Manual HS2214ECB61HE(C) ...

  • Renesas TBP-112 - page 2

    Cautions 1. Renesas neither warrants nor grants li censes of any rights of Renesas’s or any t hird party’s patent, copyright, t rademark, or other intel lect ual property rights for informat ion contained in this document. Renesas bears no responsibility fo r problem s that may arise with third party’s rights, including int ellectual property ...

  • Renesas TBP-112 - page 3

    i Preface Thank you for purchasing this user system interface cable (HS2214ECB61H) for the Renesas’s original mi crocomputer H8S/2214serie s. The HS2214ECB61H is a user system interface cable that connects an H8S/2214 series E6000 emulator (HS2214EPI61H; hereinafter referred to as the emul ator) to the IC socket for a TBP-112 package for the H8S/ ...

  • Renesas TBP-112 - page 4

    ii Contents Section 1 Configuration .................................................................................... 1 Section 2 Connection Procedures ...................................................................... 3 2.1 Connecting User System Interf ace Cable to Em ulat or Station ......................................... 3 2.2 Connecti ...

  • Renesas TBP-112 - page 5

    Section 1 Configuration CAUTION Use an CSPACK112A1110H01 socket (socket (manufactured by Toky o Eletech Corporation) for the TBP-112 package IC socket on the user system. Figure 1 shows the configuration of the HS2214E CB61H user system interface cable for the TBP-112 package. User system IC socket To emulator station Cable body Cable head Screws ( ...

  • Renesas TBP-112 - page 6

    2 Table 1 lists the HS2214ECB 61H components. Please make sure y ou have all of these com ponents when unpacking. Table 1 HS2214ECB61H Components No. Component Quantity Remarks 1 Cable body 1 Includes flat cable 2 Cable head 1 3 IC socket 1 For the TBP-112 package 4 Spacer 1 For installing an TBP-112 packaged MCU 5 Cover 1 For installing an TBP-112 ...

  • Renesas TBP-112 - page 7

    Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Emulator Station W ARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and w ill damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Always switch OFF the user system a ...

  • Renesas TBP-112 - page 8

    Figure 2 Connecting User System Int erface Cable to Emulator Station 4 ...

  • Renesas TBP-112 - page 9

    2.2 Connecting User System Interface Cable to User System W ARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part. Before connecting, make sure that pin 1 on both sides are correctly aligned. Failure to do so will result in a FIRE HAZARD and will damage the ...

  • Renesas TBP-112 - page 10

    6 (4) Notes on soldering the IC socket a) The IC socket is larger th an the actual IC package; theref ore, refer to figure 7 for the installati on of other components. b) Do not instal l components that occupy large volum e close to the IC socket. Such components will prevent the convectiv e flow of heat during reflow. c) Since the IC socket has a ...

  • Renesas TBP-112 - page 11

    7 CAUTION 1. Never dip the IC socket in flux or use wash to clean the IC socket. This is because flux may remain inside the IC socket due to the IC socket’s structure. When using the IC socket with other DIP products, never clean the other DIP products with flux because the flux may enter the connector through the guide pins of the IC socket. 2. ...

  • Renesas TBP-112 - page 12

    2.2.2 Inserting Cable Head CAUTION Check the location of pin 1 before inserting. Align pin 1 on the IC socket for an TB P-112 package on the user system wi th pin 1 on the user system interface cable head, and inse rt the user system interface cable head into the IC socket on the user system, as shown in fi gure 3. Figure 3 Connecting User System I ...

  • Renesas TBP-112 - page 13

    2.2.3 Fastening Cable Head CAUTION 1. Use the screwdriver w hose head matches the screw head. 2. The tightening torque must be 0.054 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening. If a screw is tighten ...

  • Renesas TBP-112 - page 14

    2. Next, fasten screws to ② and ④ a little, so that four screw holes are aligned. Then, each screw should be tightened a little at a time, alterna ting between screws on opposing corners. 2 4 Figure 5 Fastening Cable Head Procedure (2) 10 ...

  • Renesas TBP-112 - page 15

    2.2.4 Fastening Cable Body Connect the cable body to the cable head. Figure 6 Fastening Cable Body 11 ...

  • Renesas TBP-112 - page 16

    2.3 Recommended Dimensions for User System Mount Pad Figure 7 shows t he recomm ended dim ensions for the mount pad (footprint) for the user system with an IC socket for an TBP-112 package (CSPACK112A1110H01: socket (manufactured by Toky o Eletech Corporation). Note t hat the dimensions in figure 7 are som ewhat different from those of the actual c ...

  • Renesas TBP-112 - page 17

    2.4 Dimensions for User System Interface Cable Head The dimensions for the user system interf ace cable head are shown in figure 8. Figure 8 Dimensions for User System Interface Cable Head 13 ...

  • Renesas TBP-112 - page 18

    2.5 Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after conn ecting the user system interface cab le head to the user system, are shown in figure 9. Figure 9 Resulting Dimensions after Connecting User System Interface Cable 14 ...

  • Renesas TBP-112 - page 19

    15 Section 3 Installing the MCU to the User System CAUTION 1. Check the location of pin 1 before inserting. 2. Use a provided screwdriver. 3. The tightening torque must be 0.054 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn the screw becomes significantly greater than that needed ...

  • Renesas TBP-112 - page 20

    Figure 10 Installing MCU to User System 16 ...

  • Renesas TBP-112 - page 21

    Section 4 Verifying Operation 1. When using the E6000 emulator for the H8S/2214 series, turn on the emulator according to the procedures described in the H8S Series E6000 Em ulator User's Manual (HS2000EPI61HE). 2. Verify the user system interface cable connec tions by accessing the exte rnal m emory and ports to check the bus states of the pi ...

  • Renesas TBP-112 - page 22

    Section 5 Notice 1. Make sure that pin 1 on the user syst em IC socket is correct ly aligned with pin 1 on t he cable head before inserting the cable head into the user system IC socket. 2. The dimensi ons of the recommended m ount pad for the user system IC socket are different from those of the MCU. 3. This user system interface cable is specifi ...

メーカー Renesas カテゴリー Computer Hardware

Renesas TBP-112のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- TBP-112の取扱説明書
- Renesasの製品カード
- パンフレット
- またはRenesas TBP-112の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Renesas TBP-112の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Renesas TBP-112の取り付け説明書、サービスマニュアル、簡易説明書、またはRenesas TBP-112のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Renesas TBP-112の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Renesas TBP-112デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがRenesas TBP-112を使用するのを助ける技術的文書のことです。説明書は通常、全てのRenesas TBP-112ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Renesasの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Renesas TBP-112の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははRenesas TBP-112の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Renesas TBP-112に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Renesas TBP-112デバイスの基本機能を使うにあたってのヒント。 Renesas TBP-112のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Renesas TBP-112に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるRenesas TBP-112のメーカー/サービスへの連絡先に関する情報。

Renesas TBP-112についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもRenesas TBP-112の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがRenesas TBP-112で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)