Graco TI1962Aの取扱説明書

28ページ 1.22 mb
ダウンロード

ページに移動 of 28

Summary
  • Graco TI1962A - page 1

    311689G ENG Instructions/Parts List TRITON ® 3D350HP Diaphragm Pump Used to pump waterborne and solvent-based paints and catalysts. Part No. 253707, Series D 3:1 Ratio Air-Operated Double Diaphragm Pump, with BSPP Fittings Part No. 253708, Series D 3:1 Ratio Air-Operated Double Diaphragm Pump, with npt Fittings 0.6 MPa, 6 bar (88 psi) Maximum Air ...

  • Graco TI1962A - page 2

    2 Contents W a r n i n g ................................... 3 I n s t a l l a t i o n ................................ 5 General Information ...................... 5 Tighten Threaded Connections .............. 5 Mounting the Pump ....................... 6 A i rL i n e ................................ 7 F l u i dS u c t i o nL i n e ............... ...

  • Graco TI1962A - page 3

    3 The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama- tion point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risk. Refer back to these warnings. Additional, product-specific warnings may be found throughout the body of this manual where appli ...

  • Graco TI1962A - page 4

    4 TOXIC FLUID HAZARD Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin, inhaled, or swallowed. • Know the specific hazards of the fluid you are using. • Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local, state and national guidelines. • Alway ...

  • Graco TI1962A - page 5

    Installation 5 Installation General Information •F IG . 3 on page 8 is only a guide for installing system components and accessories. It is not an actual sys- tem design. Contact your Graco distributor for assis- tance in designing a system to suit your particular needs. • Always use Genuine Graco Parts and Accessories, available from your Grac ...

  • Graco TI1962A - page 6

    Installation 6 Mounting the Pump For ease of operation and service, mount the pump so the air inlet, fluid inlet, and fluid outlet ports are easily accessible. The inlet port must point down and the outlet port must point up. Use 5/8 in. lag screws or bolts for mounting. Wall Mount Installation 1. Wall Mount Kit 245875 is available. See F IG .1 . 2 ...

  • Graco TI1962A - page 7

    Installation 7 Air Line 1. Install the air line accessories as shown in F IG .3 . Mount these accessories on the wall or on a bracket. Be sure the air line supplying the accesso- ries is grounded. a. Install an air regulator (C) and gauge to control the fluid pressure. The fluid outlet pressure will be three times the setting of the air regulator. ...

  • Graco TI1962A - page 8

    Installation 8 Key: A Air Supply Line B Bleed-Type Master Air Valve C Air Regulator D Air Line Filter E Fluid Suction Line F Fluid Supply G Fluid Drain Valve H Fluid Shutoff Valve J Fluid Line K Mounting Bracket L Internal Air Relief Valve M Muffler N Air Line Quick Disconnect Coupler P Pump Air Piston R Pump Diaphragms S Pump Ball Checks T Air Shu ...

  • Graco TI1962A - page 9

    Installation 9 Grounding Ground all of this equipment: • Pump: use a ground wire and clamp. See F IG .4 . Loosen the grounding screw (X). Insert one end of a 1.5 mm 2 (12 ga) minimum ground wire (Y) into the pump’s grounding clamp (8) and tighten the screw (X) securely. Connect the other end of the wire to a true earth ground. For a ground wire ...

  • Graco TI1962A - page 10

    Operation 10 Operation Pressure Relief Procedure 1. Shut off the air to the pump. 2. Open the dispensing valve, if used. 3. Open the fluid drain valve to relieve all fluid pres- sure, having a container ready to catch the drain- age. Flush the Pump Before First Use The pump was tested in oil. If the oil could contaminate the fluid you are pumping, ...

  • Graco TI1962A - page 11

    Maintenance 11 Maintenance Lubrication Flushing and Storage Flush the pump with a compatible solvent often enough to prevent the fluid you are pumping from drying in the pump and damaging it. Follow the Pressure Relief Pro- cedure on page 10 before storing it for any length of time. Tighten Threaded Connections 1. Before each use, check all hoses f ...

  • Graco TI1962A - page 12

    Troubleshooting 12 Troubleshooting Relieve the pressure (page 10) before checking or servicing the equipment. Check all possible problems and causes before disassembling the pump. Problem Cause Solution Pump cycles at stall or fails to hold pressure at stall. Worn check valve balls (56), seats (53), or ball guides (57). Replace. See page 19. Pump w ...

  • Graco TI1962A - page 13

    Troubleshooting 13 F IG . 5. Cutaway Views of Pump and Air Valve Fluid Outlet Outlet Ball Check Diaphragm Air Piston Inlet Ball Check Outlet Manifold Tube Fluid Inlet Inlet Manifold Tube Outlet Ball Check Diaphragm Inlet Ball Check Diaphragm Shaft Optional Fluid Outlet Air Valve Air Valve Gasket Diaphragm Shaft Air Valve Cup Carriage Driver Carriag ...

  • Graco TI1962A - page 14

    Repair 14 Repair Prepare the Pump for Repair 1. Flush the pump if possible, page 11. 2. Relieve the pressure, page 10. 3. Disconnect the air and fluid hoses. 4. Remove the pump from its mounting and take it to the work bench. General Repair Notes Fault Indications During operation, check for indications of worn or dam- aged parts, such as: • majo ...

  • Graco TI1962A - page 15

    Repair 15 Replace the Diaphragms Disassembly 1. Prepare the pump for repair, page 14. 2. Remove the screws (31) from one fluid cover (1). Pull the cover assembly off, separating it from the fluid tubes (12). See F IG .6 . 3. Remove the fluid tubes (12) from the other cover assembly. 4. Remove the screws (31) and the remaining fluid cover (1). 5. In ...

  • Graco TI1962A - page 16

    Repair 16 F IG . 6. Replace the Diaphragms 13* 12 13* 14* 13* 12 13* 14* 31 31 1 40 1 2 3 Lubricate. Torque to 20 N•m (15 ft-lb) 1 2 2 1 1 1 1 2 TI1959A 4 4 TI8632A TI8633A Diaphragm Repair Tool 261695 ...

  • Graco TI1962A - page 17

    Repair 17 Repair the Air Valve Disassembly 1. Prepare the pump for repair, page 14. 2. Remove the screws (31) from one fluid cover (1). Pull the cover assembly off, separating it from the fluid tubes (12). See F IG .7 . 3. Remove the screws (31) and the other fluid cover (1) assembly, keeping the fluid tubes (12) attached. 4. Remove the air inlet f ...

  • Graco TI1962A - page 18

    Repair 18 12. Install the cup (47†) in the center housing. 13. Install the o-rings (43†, 44†, and 80†) on the air valve seat (33†). Lubricate the o-rings. Install the seat in the center housing (5), oriented with the spring pin (34). 14. Install the gasket (35†), cover (36), and screws and washers (38, 37). Torque to 6 N•m (4.4 ft-lb) ...

  • Graco TI1962A - page 19

    Repair 19 Replace the Ball Check Valves Disassembly 1. Prepare the pump for repair, page 14. 2. Remove the screws (38) and take the tube assem- blies off the pump. See F IG .8 . 3. Remove the springs (65), ball guides (57), and balls (56) from the outlet (top) check valves. 4. Insert a dowel through the outlet seats (53) and push the inlet (bottom) ...

  • Graco TI1962A - page 20

    Repair 20 F IG . 8. Replace the Ball Check Valves 12 38 2 65‡ 57‡ 56‡ 55 ★ 54 59 ★ 53‡ 65‡ 57‡ 56‡ 53‡ 59 ★ 58 3 38 12 4 38 58 ‡53 ‡56 ‡57 ‡65 ★ 59 ‡65 ‡57 ‡56 ★ 55 54 38 4 59 ★ ‡53 ★ 59 ★ 59 Torque to 10 N•m (7.4 ft-lb) 1 1 1 1 1 TI1960A 1 1 ...

  • Graco TI1962A - page 21

    Repair 21 Replace the Cylinder and Piston Seals Disassembly 1. Prepare the pump for repair, page 14. 2. Remove the screws (38) and tube assemblies. See F IG .9 . 3. Disassemble the ball check valves, page 19. The flat seals (55, 59) are included with this repair kit. 4. Remove the air inlet fitting (40). 5. Remove the screws (68) and the top (67) a ...

  • Graco TI1962A - page 22

    Repair 22 12. Install the diaphragms (14), page 15. 13. Install the fluid covers (1). The arrows must point up. Torque the screws (31) to 20 N•m (15 ft-lb). 14. Check that the felt strips (71) are in place on the inside of the top (67) and bottom (66) covers. Install the covers. The hole for the air inlet fitting must align with the port in the c ...

  • Graco TI1962A - page 23

    Parts 23 Parts Part No. 253707 includes items 1-81 Part No. 253708 includes items 1-8,10-59, 61-81 38 37 36 35† †33 †43 †44 †47 45 67 5 13* 12 13* 38 2 65‡ 57‡ 56‡ 55 ◆★ 54 59 ◆★ ‡53 1 31 65‡ 57‡ 56‡ 53‡ 59 ◆★ 58 3 38 13* 12 13* 68 66 68 7 22 ◆ 22 ◆ 11 20† 18 19† 21 14* 4 38 10 9 58 59 ◆★ ‡53 ‡5 ...

  • Graco TI1962A - page 24

    Parts 24 Part No. 253707 includes items 1-81 Part No. 253708 includes items 1-8,10-59, 61-81 * Included in Diaphragm Repair Kit 243152.1 † Included in Air Valve Repair Kit 243153. ‡ Included in Ball Check Valve Repair Kit 243154. ◆ Included in Cylinder Seal Repair Kit 243155. ★ Included in Sealing Ring Repair Kit 243156. NOTE: ▲ Replaceme ...

  • Graco TI1962A - page 25

    Technical Data 25 Technical Data Category Data Maximum fluid working pressure 1.8 MPa, 18 bar (260 psi) Maximum air input pressure 0.6 MPa, 6 bar (88 psi) Ratio 3:1 Maximum recommended flow rate (continuous duty) 7.6 liters/min (2.0 gpm) Maximum recommended cycle rate 20 cycles/minute Maximum flow rate 114 liters/min (30 gpm) Volume per cycle (doub ...

  • Graco TI1962A - page 26

    Performance Charts 26 Performance Charts CYCLES PER MINUTE AIR CONSUMPTION m 3 /min (scfm) FLUID OUTLET PRESSURE MPa, bar (psi) FLUID FLOW lpm (gpm); tested in No. 10 weight oil (280) (240) (200) (160) (120) (80) (40) 0 1.9, 19 1.7, 17 1.4, 14 1.0, 11 0.8, 8 0.6, 5.5 0.3, 2.8 22 43 65 87 109 130 152 174 196 217 239 0 (42) (35) (28) (21) (14) (7) 0 ...

  • Graco TI1962A - page 27

    Dimensions 27 Dimensions Wall Mount Hole Pattern For Accessory Wall Mount Kit 245875 Torque Sequence 360 mm (14.2 in.) 318 mm (12.5 in.) 146 mm (5.7 in.) 160 mm (6.3 in.) 213 mm (8.4 in.) M8 Mounting Holes Air Inlet; see page 25 for sizes. Fluid Inlet; see page 25 for sizes. Fluid Outlet; see page 25 for sizes. TI1964A TI1963A 100 mm (4 in.) 260 mm ...

  • Graco TI1962A - page 28

    All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice. This manual contains English. MM 311689 Graco Headquarters: Minneapolis International Offices: Belgium, China, Japan, Korea GRACO INC. P.O. BOX 1441 ...

メーカー Graco カテゴリー Marine Sanitation System

Graco TI1962Aのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- TI1962Aの取扱説明書
- Gracoの製品カード
- パンフレット
- またはGraco TI1962Aの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Graco TI1962Aの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Graco TI1962Aの取り付け説明書、サービスマニュアル、簡易説明書、またはGraco TI1962Aのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Graco TI1962Aの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Graco TI1962Aデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがGraco TI1962Aを使用するのを助ける技術的文書のことです。説明書は通常、全てのGraco TI1962Aユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Gracoの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Graco TI1962Aの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははGraco TI1962Aの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Graco TI1962Aに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Graco TI1962Aデバイスの基本機能を使うにあたってのヒント。 Graco TI1962Aのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Graco TI1962Aに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるGraco TI1962Aのメーカー/サービスへの連絡先に関する情報。

Graco TI1962Aについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもGraco TI1962Aの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがGraco TI1962Aで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)