日本語 dropdown-ico

Delta 36-650の取扱説明書

32ページ 1.52 mb
ダウンロード

ページに移動 of 32

Summary
  • Delta 36-650 - page 1

    INSTRUCTION MANUAL 10" Pr ofessional T able Saw (Model 36-650) P ART NO. 902113 - 11-22-02 Copyright © 2002 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582). ...

  • Delta 36-650 - page 2

    2 W oodworking can be dangerous if safe and pr oper operating procedures ar e not followed. As with all machinery , ther e are certain hazar ds involved with the operation of the product. Using the machine with respect and caution will considerably lessen the possibility of personal injury . However , if normal safety precautions ar e overlooked or ...

  • Delta 36-650 - page 3

    3 17. REDUCE THE RISK OF UNINTENTIONAL ST ARTING . Make sure switch is in “OFF” position befor e plugging in power cord. In the event of a power failure, move switch to the “OFF” position. 18. NEVER ST AND ON TOOL . Serious injury could occur if the tool is tipped or if the cutting tool is accidentally contacted. 19. CHECK DAMAGED P ARTS . ...

  • Delta 36-650 - page 4

    4 POWER CONNECTIONS A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wire extension cords which have 3- prong gr ounding type plugs and matching receptacle which will accept the machine’ s pl ...

  • Delta 36-650 - page 5

    Use proper extension cor ds. Make sure your extension cord is in good condition and is a 3-wir e extension cord which has a 3-pr ong grounding type plug and matching receptacle which will accept the machine’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the current of the machine. An undersized cord will cause a ...

  • Delta 36-650 - page 6

    6 10" PROFESSIONAL T ABLE SA W P ARTS Fig. 2 1. T able Saw 2. Extension Wing (2) 3. Motor 4. Pulley Guard Plate 5. Switch Assembly 6. Lock Knob (2) 7. Handwheel (2) 8. Miter Gage Handle 9. Motor Plate 10. Motor Pulley 11. Miter Gage Body 12. Miter Gage Guide Bar 13. T able Insert 14. Splitter Bracket 15. Blade Guard and Splitter Assembly 16. S ...

  • Delta 36-650 - page 7

    1. Leg (4) 2. Bracket 24" Long (2) 3. Bracket 21" Long (2) 4. T op Bracket (1) 5. Plastic Foot (4) Fig. 4 ST AND P AR TS 7 HARDW ARE 1. 7/16-20x3/4" Hex Head Screw (6) 2. 3/8-16x1½" Flat Head Screw (4) 3. 3/8-16x1" Hex Head Screw (4) 4. 5/16-18x3/4" Carriage Head Screw (4) 5. 5/16-18x5/8" Hex Head Screw (8) 6. 5/ ...

  • Delta 36-650 - page 8

    ASSEMBL Y ST AND LEGS 1. Assemble the longer bottom bracket (A) Fig. 6, to the inside of two table legs (B) as shown. Align the holes in the longer bottom bracket (A) Fig. 6, with the holes in the table legs (B). Insert a 5/16-18x5/8" carriage head bolt through the hole in the table leg (B) and the hole in the longer bottom bracket (B), place ...

  • Delta 36-650 - page 9

    9 4. WITH A MINIMUM OF TWO PEOPLE, CAREFULL Y TURN THE SAW AND ST AND UPRIGHT AS SHOWN IN FIG. 10. Carefully push down on the top of the saw until the stand legs adapt to the floor surface and firmly tighten all stand mounting hardwar e. Fig. 10 BLADE TIL TING AND RAISING HANDWHEEL 2. Assemble the blade raising handwheel (A) Fig. 12, to the front o ...

  • Delta 36-650 - page 10

    10 INST ALLING SWITCH AND MOTOR CORD 1. Insert switch cord (A) Fig. 13, and motor cord (B) of the switch assembly into the opening (C) under saw table as shown, and into the inside of the saw cabinet Fig. 14. 2. Insert switch cord (A) Fig. 14, and motor cord (B) into clamps (D) and loosely fasten both cords (A) and (B) Fig. 15, to the saw cabinet b ...

  • Delta 36-650 - page 11

    11 MOTOR TO MOTOR MOUNTING PLA TE DISCONNECT MACHINE FROM POWER SOURCE. Assemble motor (A) to motor mounting plate (B) as shown in Fig. 16. Align the four mounting holes in the motor with the four holes in the mounting plate. Insert a 5/16- 18x3/4" carriage bolt (C), through the hole in motor and then through the hole in the motor mounting pla ...

  • Delta 36-650 - page 12

    12 MOTOR PULLEY , PULLEY GUARD, AND DRIVE BEL T DISCONNECT MACHINE FROM POWER SOURCE. 1. Remove the motor shaft key that is taped to the motor . 2. Insert key (A) Fig. 20, in the keyway on the motor shaft. Assemble motor pulley (B) on motor shaft as shown, with the hub of the pulley out. Tighten set screw (C) against key (A) in motor shaft. 3. Slid ...

  • Delta 36-650 - page 13

    13 2. Fig. 28, illustrates the motor cord connected to the switch assembly . CONNECTING MOTOR CORD TO SWITCH ASSEMBL Y DISCONNECT MACHINE FROM POWER SOURCE. 1. Insert the pronged motor plug (A) Fig. 27, into the female receptacle (B) of switch-to-motor cor d (C). 8. IMMEDIA TEL Y AFTER ASSEMBLING THE BEL T , RAISE THE SAW BLADE TO ITS MAXIMUM HEIGH ...

  • Delta 36-650 - page 14

    14 BLADE GUARD AND SPLITTER ASSEMBL Y DISCONNECT MACHINE FROM POWER SOURCE. 1. Fasten the rear splitter mounting bracket (A) Fig. 29, to the rear trunnion. Align the two holes in the r ear splitter mounting bracket with the two holes in the trunnion. Place a 1/4" lock washer onto a 1/4-20x3/4" hex head screw , place a 1/4" flat washe ...

  • Delta 36-650 - page 15

    15 7. Assemble the blade guard and splitter assembly (G) Fig. 33, between the lar ge washer (C) and the splitter bracket and tighten screw (H) with wr ench supplied. 8. Fasten the r ear of the blade guard and splitter bracket assembly (G) Fig. 34, to the rear splitter mounting bracket. Align the hole in the blade guard and splitter bracket with the ...

  • Delta 36-650 - page 16

    16 10. Using a straight edge, check to see if the saw blade is aligned with the rear of the splitter (G), as shown in Fig. 37. If alignment is necessary , loosen the screws (A) Fig. 37, align splitter (G) with the saw blade, and tighten two screws (A). 11. Lower saw blade and install table insert (P) Fig. 38, in the saw table as shown. THE T ABLE I ...

  • Delta 36-650 - page 17

    17 3. Before tightening the har dware holding the guide rail to the saw table, proceed as follows: Beginning at the two sides of the saw table and using an adjustable square (F) Fig. 41, or a ruler , check to make certain the guide rail (A) is parallel with the saw table and extension wings. Tighten all guide rail mount ing hardwar e. 4. Insert end ...

  • Delta 36-650 - page 18

    18 3. Lower the front of rip fence (B) Fig. 46, onto the front guide rail (L). 4. Lock the rip fence (B) Fig. 46, on the guide rails by pushing down handle (A). RIP FENCE TO GUIDE RAILS 1. Insert end cap (A) Fig. 45, into back of rip fence (B). 2. With the fence handle (A) Fig. 46, in the raised position, place the rip fence (B) onto the rear guide ...

  • Delta 36-650 - page 19

    19 LOCKING SWITCH IN THE “OFF” POSITION IMPORT ANT : When the tool is not in use, the switch (B) Fig.56, should be locked in the OFF position using a padlock (C), with a 3/16" diameter shackle to prevent unauthorized use. ST ARTING AND STOPPING SA W 1. The on/off switch is located underneath the switch shield (A) Fig. 54. T o tur n the saw ...

  • Delta 36-650 - page 20

    20 RAISING AND LOWERING THE BLADE T o raise the saw blade, loosen lock knob (A) Fig. 58, and turn the blade raising handwheel (B) clockwise. When the blade is at the desired height, tighten lock knob (A). T o lower the blade, loosen lock knob (A) Fig. 58, and tur n the handwheel (B) counterclockwise. NOTE: One full turn of the handwheel will change ...

  • Delta 36-650 - page 21

    21 BACKLASH ADJUSTMENTS FOR BLADE RAISING AND BLADE TIL TING MECHANISMS If any play is detected in the blade raising or blade tilting mechanisms, the following adjustments should be made. DISCONNECT MACHINE FROM POWER SOURCE. 1. NOTE: The machine has been turned upside down and the blade removed for clarity and safety . 2. Adjusting blade raising m ...

  • Delta 36-650 - page 22

    22 5. Depending on the type of saw blade being used, the cursor (D) Fig. 64, may need adjustment to compensate for the blade thickness.T o adjust the cursor , make a test cut on a piece of lumber and measure the finished cut, or you can place the rip fence against the blade as shown earlier in the manual. If a minor adjustment is necessary , loosen ...

  • Delta 36-650 - page 23

    23 ADJUSTING T ABLE INSERT DISCONNECT MACHINE FROM POWER SOURCE. Place a straight edge across the table at both ends of the table insert as shown in Fig. 68. The table insert (A) should always be level with the table. If an adjustment is necessary , tur n the adjusting screws (B), as needed. Four adjusting screws (B) ar e supplied in the table inse ...

  • Delta 36-650 - page 24

    24 OPERA TIONS Common sawing operations include ripping and crosscutting plus a few other standar d operations of a fundamental nature. As with all power tools, ther e is a certain amount of hazard involved with the operation and use of the machine. Using the machine with the respect and caution demanded as far as safety pr ecautions are concerned, ...

  • Delta 36-650 - page 25

    25 RIPPING Ripping is the operation of making a lengthwise cut through a boar d, as shown in Fig. 82, and the rip fence (A) is used to position and guide the work. One edge of the work rides against the rip fence while the flat side of the board r ests on the table. Since the work is pushed along the fence, it must have a straight edge and make sol ...

  • Delta 36-650 - page 26

    26 For certain cutting operations such as dadoing and moulding where you ar e not cutting completely through the workpiece, the blade guar d and splitter assembly cannot be used. Loosen screws (G) and (H) Fig. 85. Lift up and swing blade guard and splitter assembly (W) Fig. 86, to the rear of the saw , and then tighten screws (G) and (H). Always re ...

  • Delta 36-650 - page 27

    27 USING ACCESSOR Y DADO HEAD THE BLADE GUARD AND SPLITTER ASSEMBL Y CANNOT BE USED WHEN DADOING OR MOULDING AND MUST BE REMOVED OR SWUNG TO THE REAR OF THE SAW . Dadoing is cutting a rabbet or wide groove into the work. Most dado head sets are made up of two outside saws and four or five inside cutters, as shown in Fig. 89. V arious combinations o ...

  • Delta 36-650 - page 28

    28 USING AUXILIAR Y WOOD F ACING ON RIP FENCE It is necessary when performing special operations such as moulding to add wood facing (A) Fig. 94, to one or both sides of the rip fence, as shown. The wood facing is attached to the fence with wood screws (B), countersunk and assembled through the holes provided in the fence. 3/4 inch stock is suitabl ...

  • Delta 36-650 - page 29

    29 PUSH STICK MAKE FROM 1/2" OR 3/4" WOOD OR THICKNESS LESS THAN WIDTH OF MA T’L. TO BE CUT CUT OFF HERE TO PUSH 1/4" WOOD CUT OFF HERE TO PUSH 1/2" WOOD NOTCH TO HELP PREVENT HAND FROM SLIPPING 1/2" SQUARES CONSTRUCTING A PUSH STICK When ripping work less than 4 inches wide, a push stick should be used to complete the fe ...

  • Delta 36-650 - page 30

    30 Printed in U.S.A. T wo Y ear Limited W arranty Delta will repair or r eplace, at its expense and at its option, any Delta machine, machine part, or machine accessory which in normal use has proven to be defective in workmanship or material, pr ovided that the customer returns the product prepaid to a Delta factory service center or authorized se ...

  • Delta 36-650 - page 31

    NOTES 31 ...

  • Delta 36-650 - page 32

    The following are trademarks of POR TER-CABLE · DEL T A (Las siguientes son marcas r egistradas de PORTER-CABLE S.A.): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’ s Saw ® , Contractor’ s Saw ® , Contractor’ s Saw II™, Delta ® , DEL T ACRAFT ® , DEL T AGRAM™, Delta Series 2000™, DURA TRONIC™, Emc²™, FLEX ® , Flying Chips? ...

メーカー Delta カテゴリー Saw

Delta 36-650のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 36-650の取扱説明書
- Deltaの製品カード
- パンフレット
- またはDelta 36-650の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Delta 36-650の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Delta 36-650の取り付け説明書、サービスマニュアル、簡易説明書、またはDelta 36-650のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Delta 36-650の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Delta 36-650デバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがDelta 36-650を使用するのを助ける技術的文書のことです。説明書は通常、全てのDelta 36-650ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Deltaの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Delta 36-650の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははDelta 36-650の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Delta 36-650に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Delta 36-650デバイスの基本機能を使うにあたってのヒント。 Delta 36-650のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Delta 36-650に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるDelta 36-650のメーカー/サービスへの連絡先に関する情報。

Delta 36-650についてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもDelta 36-650の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがDelta 36-650で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)