Zenoah HTZ7510, CHTZ6010の取扱説明書

24ページ 3.54 mb
ダウンロード

ページに移動 of 24

Summary
  • Zenoah HTZ7510, CHTZ6010 - page 1

    HTZ7510 CHTZ6010 848D3L93A1 (704) OWNER’S MANUAL HEDGE-TRIMMERS • Before using our products, please read this manual carefully to understand the proper use of your unit. • Keep this manual handy. CA UTION ...

  • Zenoah HTZ7510, CHTZ6010 - page 2

    ...

  • Zenoah HTZ7510, CHTZ6010 - page 3

    SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail. ■ NOTES ON TYPES OF WARNINGS IN THE MANUAL Thi ...

  • Zenoah HTZ7510, CHTZ6010 - page 4

    4 1. Right handle 2. Fuel tank 3. Starter 4. Left handle 5. Throttle lever 6. Engine switch 7. Muffler 8. Blade 9. Front handle 10. Rear handle 11. Plate receive 12. Engine stop switch English 1. PARTS LOCATION ...

  • Zenoah HTZ7510, CHTZ6010 - page 5

    English For safe operation and maintenance, symbols are carved in relief on the machine. According to these indications, please be careful not to take a mistake. (a). The port to refuel the "MIX GASOLINE" POSITION: FUEL TANK CAP (b).The direction to close the choke POSITION: AIR CLEANER COVER (c). The direction to open the choke POSITION: ...

  • Zenoah HTZ7510, CHTZ6010 - page 6

    6 3. SAFETY PRECAUTIONS ■ BEFORE USING THE MACHINE a. Read this owner's manual carefully to understand how to operate this unit properly. b. This product has been designed for use in trimming leaves and branches from trees and hedges, and it should never be used for any other purpose since doing so could result in unforeseen accidents and in ...

  • Zenoah HTZ7510, CHTZ6010 - page 7

    3. SAFETY PRECAUTIONS g. Lack of sleep, tiredness, or physical exhaustion results in lower attention spans, and this in turn leads to accidents and injury. Limit the amount of time over which the hedge-trimmer is to be used continuously to somewhere around 30~40 minutes per session, and take 10~20 minutes of rest between work sessions. Also try to ...

  • Zenoah HTZ7510, CHTZ6010 - page 8

    8 3. SAFETY PRECAUTIONS ■ WARNING CONSIDERING HANDLING OF FUEL a. The engine of this product is designed to run on a mixed fuel which contains highly flammable gasoline. You should never store cans of fuel or refill the fuel tank in any place where there is a boiler, stove, wood fire, electrical sparks, welding sparks, or any other source of heat ...

  • Zenoah HTZ7510, CHTZ6010 - page 9

    3. SAFETY PRECAUTIONS persons, always check the presence and locations of others so as to maintain a distance each person sufficient to ensure safety. c. Make sure that there are no loose screws or bolts, fuel leaks, ruptures, dents, or any other problems which might interfere with safe operation. Be especially careful to check that there is nothin ...

  • Zenoah HTZ7510, CHTZ6010 - page 10

    10 3. SAFETY PRECAUTIONS ■ KICKBACK SAFETY PRECAUTIONS •A dangerous reaction may occur when the spinning blade contacts a solid object in the critical area. It is called Kick back. As a result, the operator can lose control of the unit which can cause serious or fatal injury. Avoid kickback, observe the safety precautions below strictly. 1. Kee ...

  • Zenoah HTZ7510, CHTZ6010 - page 11

    3. SAFETY PRECAUTIONS d. If the grass gets caught in the blade during operation, or if you need to check the unit or refuel the tank, always be sure to turn off the engine. e. If the blade touches a hard object like a stone, immediately stop the engine and check if something is wrong with the blade. If so, replace the blade by new one. f. If someon ...

  • Zenoah HTZ7510, CHTZ6010 - page 12

    12 English d. When sharpening, removing, or reattaching the blade, be sure to wear thick, sturdy gloves and use only proper tools and equipment to prevent injury. e. When replacing blade or any other parts or when replacing the oil or any lubricants, always be sure to use only ZENOAH products or products which have been certified by ZENOAH for use ...

  • Zenoah HTZ7510, CHTZ6010 - page 13

    English 4. FUEL •G asoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. • Wipe up all spills before starting the engine. •M ake sure to stop the engine and allow it cool before refueling the unit. • Keep open flames away from the area where fuel is handled or stored. •N ever use oil for 4 cycle engine use or ...

  • Zenoah HTZ7510, CHTZ6010 - page 14

    14 [HTZ7510] [CHTZ6010] English 5. OPERATION ■ STARTING THE ENGINE Keep the blades clear of everything around It as they will start moving upon the engine starts. 1. [HTZ7510] Make sure that the throttle lever is at idling position. [CHTZ6010] Release the throttle lever and make sure it is fully back. (F1) 2. [CHTZ6010] Set the engine switch to t ...

  • Zenoah HTZ7510, CHTZ6010 - page 15

    English ■ RUNNING IN THE ENGINE During the first 20 working hours, do not use the hedge-trimmer at maximum power for long periods. ■ ADJUSTING IDLING SPEED • Before adjusting the carburetor, clean the air filter and warm up the engine. (F5) • Idle screw is adjusted in order to ensure a good safety margin between idle running and clutch enga ...

  • Zenoah HTZ7510, CHTZ6010 - page 16

    F9 F8 English • Use only as much throttle as is needed to do the job. Excessive engine speed is unnecessary. • Avoid cutting thick branches, for which will damage the blades and shorten the life of drive systems. • Tilting the trimmer 5 to 10° to the cutting object will make the job easy and bring a good result. •A lways keep your body to ...

  • Zenoah HTZ7510, CHTZ6010 - page 17

    17 Every Every Every Before 25 50 100 System/compornent Procedure use hours hours hours note after after after fuel leaks, fuel spillage wipe out ✔ fuel tank, air filter, fuel filter inspect/clean ✔✔ replace, if necessary see ADJUSTING replace carburetor idle adjusting screw ✔ IDLING SPEED if necessary clean and readjust GAP: 0.6 – 0.7 mm ...

  • Zenoah HTZ7510, CHTZ6010 - page 18

    18 English 6. MAINTENANCE F10 F12 F11 Before cleaning, inspecting, or repairing the unit, make sure that the engine has stopped and is cool. ■ BLADE (F10) • Check the blade and the fasteners for looseness, cracking, or bending. • Check the cutting edges and reform with a flat file. Point: 1. Keep the end corner sharp. 2. Round the root of the ...

  • Zenoah HTZ7510, CHTZ6010 - page 19

    English 6. MAINTENANCE F13 F14 3. Check if the safety lock returns to its original position when you release your hand from safety lock. If you find any defects at the checks above, contact your nearest servicing dealer for repair. ■ ANTI-VIBRATION SYSTEM (F13) The deformed or damaged anti- vibration system may cause of the breakages like getting ...

  • Zenoah HTZ7510, CHTZ6010 - page 20

    20 English 6. MAINTENANCE F15 F16 F17 ■ FUEL FILTER (F15) When the engine runs short of fuel supply, check the fuel strainer for blockage. ■ WAY OF THE COOLING AIR (F16) This engine is air-cooled. Dust clogging between the inlet port of the cooling air and cylinder fins will cause overheating of the engine. Periodically check and clean the cyli ...

  • Zenoah HTZ7510, CHTZ6010 - page 21

    21 English 6. MAINTENANCE F19 F20 ■ MUFFLER AFTER 100 HOURS OF USE 1. Remove the muffler, insert a screwdriver into the vent, and wipe away any carbon buildup. Wipe away any carbon buildup on the muffler exhaust vent at the same time. (F19) (1) screw driver (2) muffler 2. Tighten all screws, bolts, and fittings. 3. Check to see if any oil or grea ...

  • Zenoah HTZ7510, CHTZ6010 - page 22

    English Model name ................ HTZ7510 [CHTZ6010] Type ..............................Reciprocating single-sided [double-sided] dual blades Blade length .............................. 750 [600]mm Engine model ........................... Zenoah GZ23N Displacement ......................................... 23.6cc Carburetor ....................... ...

  • Zenoah HTZ7510, CHTZ6010 - page 23

    ...

  • Zenoah HTZ7510, CHTZ6010 - page 24

    Head Office: 1-9, Minamidai, Kawagoe-city , Saitama, 350-1 192 Japan T elephone: (+81)49-243-1 1 17 T elecopier: (+81)49-243-7197 ...

メーカー Zenoah カテゴリー Trimmer

Zenoah HTZ7510, CHTZ6010のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- HTZ7510, CHTZ6010の取扱説明書
- Zenoahの製品カード
- パンフレット
- またはZenoah HTZ7510, CHTZ6010の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Zenoah HTZ7510, CHTZ6010の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Zenoah HTZ7510, CHTZ6010の取り付け説明書、サービスマニュアル、簡易説明書、またはZenoah HTZ7510, CHTZ6010のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Zenoah HTZ7510, CHTZ6010の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Zenoah HTZ7510, CHTZ6010デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがZenoah HTZ7510, CHTZ6010を使用するのを助ける技術的文書のことです。説明書は通常、全てのZenoah HTZ7510, CHTZ6010ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Zenoahの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Zenoah HTZ7510, CHTZ6010の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははZenoah HTZ7510, CHTZ6010の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Zenoah HTZ7510, CHTZ6010に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Zenoah HTZ7510, CHTZ6010デバイスの基本機能を使うにあたってのヒント。 Zenoah HTZ7510, CHTZ6010のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Zenoah HTZ7510, CHTZ6010に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるZenoah HTZ7510, CHTZ6010のメーカー/サービスへの連絡先に関する情報。

Zenoah HTZ7510, CHTZ6010についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもZenoah HTZ7510, CHTZ6010の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがZenoah HTZ7510, CHTZ6010で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)