-
Cabletron Systems WPIM-RT1 - page 1
WPIM-RT1 Title Page WPIM-R T1 User’ s Guide 9032811 ...
-
Cabletron Systems WPIM-RT1 - page 2
...
-
Cabletron Systems WPIM-RT1 - page 3
WPIM-RT1 User’ s Guide i NOTICE Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any such changes ha ve been made. The hardware, firmware, or software described in this manual ...
-
Cabletron Systems WPIM-RT1 - page 4
Notice ii WPIM-RT1 User’ s Guide INDUSTRY CANADA NOTICE This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limi ...
-
Cabletron Systems WPIM-RT1 - page 5
Notice WPIM-RT1 User’ s Guide iii CABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENT IMPOR T ANT : Before utilizing this product, carefully read this License Agreement. This document is an agreement between you, the end user , and Cabletron Systems, Inc. (“Cabletron”) that sets forth your rights and obligations with respect to the Cabletron so ...
-
Cabletron Systems WPIM-RT1 - page 6
Notice iv WPIM-RT1 User’ s Guide UNITED STATES GOVERNMENT RESTRICTED RIGHTS The enclosed product (a) was de veloped solely at priv ate expense; (b) contains “restricted computer software” submitted with restricted rights in accordance with Section 52227-19 (a) through (d) of the Commercial Computer Software - Restricted Rights Clause and its ...
-
Cabletron Systems WPIM-RT1 - page 7
Notice WPIM-RT1 User’ s Guide v DECLARATION OF CONFORMITY Application of Council Directiv e(s): 89/336/EEC 73/23/EEC Manufacturer’ s Name: Cabletron Systems, Inc. Manufacturer’ s Address: 35 Industrial Way PO Box 5005 Rochester, NH 03867 European Representativ e Name: Mr. J. Solari European Representativ e Address: Cabletron Systems Limited N ...
-
Cabletron Systems WPIM-RT1 - page 8
Notice vi WPIM-RT1 User’ s Guide ...
-
Cabletron Systems WPIM-RT1 - page 9
WPIM-RT1 User’ s Guide vii CONTENTS INTRODUCTION ...................................................................................... ix Using This Manual .......................................................................... ix Structure of This Guide................................................................... ix Related Manuals.... ...
-
Cabletron Systems WPIM-RT1 - page 10
Contents viii WPIM-RT1 User’ s Guide 3.3 Full T1 Configuration Using PPP ............................................... 3-11 3.3.1 T1 Physical Configuration ............................................. 3-12 3.3.2 T1 Interface Configuration ............................................. 3-13 3.4 Fractional T1 Configuration Using PPP ............. ...
-
Cabletron Systems WPIM-RT1 - page 11
WPIM-RT1 User’ s Guide ix INTR ODUCTION W elcome to the Cabletron Systems WPIM-RT1 User’s Guide. This manual provides hardw are information, and explains the use of Local Management to control and manage the Cabletron Systems WPIM-R T1. The WPIM-R T1 is installed in and provides full or fractional T1 to the Cabletron Systems CSX400, HSIM-W6, an ...
-
Cabletron Systems WPIM-RT1 - page 12
Introduction x WPIM-RT1 User’ s Guide Appendix B , FCC Part 68 - User’ s Inf ormation , explains the FCC Rules for the WPIM-R T1. RELATED MANUALS Refer to the manual included with the host platform in which the WPIM-R T1 is installed to supplement the procedures and other technical data provided in this manual. This manual references procedures ...
-
Cabletron Systems WPIM-RT1 - page 13
Introduction WPIM-RT1 User’ s Guide xi DOCUMENT CON VENTIONS The follo wing con ventions are used throughout this document: NO TE Note symbol. Calls the reader’ s attention to any item of inf or mation that ma y be of special impor tance. TIP Tip symbol. Conve ys helpful hints concerning procedures or actions. ! CA UTION Caution symbol. Contain ...
-
Cabletron Systems WPIM-RT1 - page 14
Introduction xii WPIM-RT1 User’ s Guide GETTING HELP For additional support related to this de vice or document, contact Cabletron Systems using one of the follo wing methods: Before calling Cabletron Systems, have the following information ready: • Y our Cabletron Systems service contract number • A description of the failure • A descripti ...
-
Cabletron Systems WPIM-RT1 - page 15
WPIM-RT1 User’ s Guide 1-1 CHAPTER 1 OVERVIEW This chapter describes steps for operation of the WPIM-R T1. It also briefly explains WPIM-R T1 features, ISDN, and indicates where to find the W AN protocols supported by the WPIM-R T1. Some of the steps for successful operation of this de vice are: • Install the WPIM-R T1 in a W ide Area Network ...
-
Cabletron Systems WPIM-RT1 - page 16
Chapter 1: Ov er view 1-2 WPIM-RT1 User’ s Guide 1.1 WPIM-RT1 FEATURES The WPIM-R T1 extends the functionality of the W ide Area Netw ork host platform to provide a full or fractional T1 interface for the CSX400, HSIM-W6, or the HSIM-SSA710. The WPIM-R T1 provides a T1 interface that includes a b uilt-in Channel Service Unit/Digital Service Unit ...
-
Cabletron Systems WPIM-RT1 - page 17
WPIM-RT1 User’ s Guide 2-1 CHAPTER 2 SETUP AND INSTALLATION The follo wing information in this chapter details the set up and installation of the WPIM-R T1 into a host platform. 2.1 INSTALLING THE WPIM-RT1 Figure 2-1 WPIM-RT1 For additional support related to the WPIM-R T1, refer to the host platform manual into which the WPIM-R T1 is being insta ...
-
Cabletron Systems WPIM-RT1 - page 18
Chapter 2: Setup and Installation 2-2 WPIM-RT1 User’ s Guide 2.1.1 Unpacking the WPIM-R T1 1. Carefully remove the WPIM-RT1 from the shipping box. 2. Visually inspect the WPIM-RT1. If there are any signs of damage, contact Cabletron Systems immediately. Refer to Getting Help . 2.1.2 Pre-Installation T o prepare the host platform for the WPIM-RT1, ...
-
Cabletron Systems WPIM-RT1 - page 19
Installing the WPIM-RT1 WPIM-RT1 User’ s Guide 2-3 4. Press down firmly on the WPIM-RT1 until the pins slide all the way into the connector. Ensure that the WPIM-RT1 seats flush on the standoffs. 5. Secure the WPIM-RT1 to the three standoffs with the WPIM screws. Figure 2-2 Installing the WPIM-RT1 2.1.4 P ost-Installation 1. Reinstall the cover i ...
-
Cabletron Systems WPIM-RT1 - page 20
Chapter 2: Setup and Installation 2-4 WPIM-RT1 User’ s Guide 2.2 HOST PLATFORM LEDs The host platform displays LED indications of the WPIM-R T1’ s operation. For more information on LED indications, refer to the host platform manual. 2.3 REQUIRED MANAGEMENT OPERATIONS Before the W AN cable can be connected to the WPIM-R T1, you must use QuickSE ...
-
Cabletron Systems WPIM-RT1 - page 21
Connecting the W AN cable to the WPIM-RT1 WPIM-RT1 User’ s Guide 2-5 The RJ45 cable from the WPIM-R T1 must be plugged into the W AN connection wall jack (see Figure 2-3 , belo w). The cable is not supplied with the WPIM-R T1, but may be ordered separately from Cabletron Systems, cable part number 9372094. Refer to Appendix A for details. Figure ...
-
Cabletron Systems WPIM-RT1 - page 22
Chapter 2: Setup and Installation 2-6 WPIM-RT1 User’ s Guide ...
-
Cabletron Systems WPIM-RT1 - page 23
WPIM-RT1 User’ s Guide 3-1 CHAPTER 3 LOCAL MANAGEMENT This chapter explains ho w to configure the WPIM-R T1 through Local Management for T1 service on the CSX400 or the HSIM-W6. Refer to the Cabletron Systems HSIM-SSA710 User’ s Guide for information on Local Management for the HSIM-SSA710. The W AN Physical Configuration screen and the W AN ...
-
Cabletron Systems WPIM-RT1 - page 24
Chapter 3: Local Management 3-2 WPIM-RT1 User’ s Guide 3.1 THE W AN PHYSICAL CONFIGURATION SCREEN T o access the W AN Physical Configuration screen, use the arro w keys to highlight the WAN SETUP menu item, then press ENTER. The screen sho wn in Figure 3-1 displays. Figure 3-1 W AN Ph ysical Configuration Screen 3.1.1 W AN Physical Configurati ...
-
Cabletron Systems WPIM-RT1 - page 25
The W AN Physical Configuration Screen WPIM-RT1 User’ s Guide 3-3 2. Use the SPACE bar to select the appropriate WPIM, then press ENTER. The WAN Configuration screen automatically displays unique configuration fields for each WPIM as shown in Figure 3-1 . The W AN Physical Configuration screen displays the following information for each WPIM: W ...
-
Cabletron Systems WPIM-RT1 - page 26
Chapter 3: Local Management 3-4 WPIM-RT1 User’ s Guide 3.1.2 WPIM Line Configuration Fields The configuration fields displayed on the W AN Physical Configuration screen sho wn in Figure 3-1 are specific to the T1 mode of the WPIM-R T1. T1 Timeslot View (T oggle) Displays the status of the T imeslot Configuration T able. This field toggles ...
-
Cabletron Systems WPIM-RT1 - page 27
The W AN Physical Configuration Screen WPIM-RT1 User’ s Guide 3-5 • 267-399 Ft • 400-533 Ft • 534-655 Ft T1 Loopback (Selectab le) Network Loopback is a testing procedure that se gments the line and allo ws the user to isolate faults. The selections for this field are None, Line-Loop, and Payload-Loop. In Line-Loop the entire T -1 line is ...
-
Cabletron Systems WPIM-RT1 - page 28
Chapter 3: Local Management 3-6 WPIM-RT1 User’ s Guide Figure 3-3 sho ws a sample configuration for three sites. Of the 24 T imeslots, Site #1 uses 16 to communicate with Site #2 and the remaining 8 to communicate with Site #3. This configuration v aries tremendously depending on ho w the service provider maps out the T1 T imeslots. The service ...
-
Cabletron Systems WPIM-RT1 - page 29
The W AN Interface Configuration Screen WPIM-RT1 User’ s Guide 3-7 3.2 THE W AN INTERFACE CONFIGURATION SCREEN This section describes the features of the W AN Interface Configuration screen. Access the screen by using the arrow ke ys to highlight the W AN INT CONFIG command field at the bottom of the W AN Physical Configuration screen, then p ...
-
Cabletron Systems WPIM-RT1 - page 30
Chapter 3: Local Management 3-8 WPIM-RT1 User’ s Guide Active Protocol (Read-Only) Displays the acti v e OSI layer protocol (Protocol Manager) chosen for the WPIM-R T1. There is one set of parameters displayed for FR, and one set for PPP . Refer to Section 3.2.1.1 for information on the Acti ve Protocol set to Frame Relay , and Section 3.2.1.2 fo ...
-
Cabletron Systems WPIM-RT1 - page 31
The W AN Interface Configuration Screen WPIM-RT1 User’ s Guide 3-9 3.2.1.2 PPP as the Protocol Mana ger Figure 3-5 W AN Interface Configuration Screen (PPP) Refer to Figure 3-5 for the follo wing parameters displayed for PPP . PPP MRU (Modifiab le) Displays the Maximum Recei ve Units that PPP can handle, modifiable by the user . ECP Enable (T ...
-
Cabletron Systems WPIM-RT1 - page 32
Chapter 3: Local Management 3-10 WPIM-RT1 User’ s Guide 3.2.1.3 Command Fields and Interface T able Fields SA VE (Command) Used to sav e the configuration changes. PORTS: [1-32] (Command) Interface table displays the range of circuits sho wn in the command field. The SP A CE bar and either the B A CKSP A CE or DELETE ke y is used to step throug ...
-
Cabletron Systems WPIM-RT1 - page 33
Full T1 Configuration Using PPP WPIM-RT1 User’ s Guide 3-11 3.3 FULL T1 CONFIGURATION USING PPP This section provides step-by-step instructions for configuring the WPIM-R T1 to use a full T1 circuit in a PPP en vironment. This simplified example assumes the setup sho wn in Figure 3-6 using a CSX400 with a WPIM-R T1 installed at Site #1. Confi ...
-
Cabletron Systems WPIM-RT1 - page 34
Chapter 3: Local Management 3-12 WPIM-RT1 User’ s Guide 3.3.1 T1 Physical Configuration Begin the T1 configuration by accessing the W AN Physical Configuration screen through Local Management ( Figure 3-1 ). Access the W AN Physical Configuration screen from the W AN SETUP menu item in the host platform. Proceed with the follo wing steps: 1. ...
-
Cabletron Systems WPIM-RT1 - page 35
Full T1 Configuration Using PPP WPIM-RT1 User’ s Guide 3-13 7. Use the arrow keys to highlight T1 TX Clock Source . Press the SPACE bar to select Local (no clock source provided by telephone company) or Loop (clock source provided by telephone company), then press ENTER. 8. Use the arrow keys to highlight T1 Line Buildout (LBO). Press the SPACE ...
-
Cabletron Systems WPIM-RT1 - page 36
Chapter 3: Local Management 3-14 WPIM-RT1 User’ s Guide 4. Use the arrow keys to highlight the SAVE command, then press ENTER. The message “SAVE DONE!” displays and Local Management saves the changes to memory. The W AN configuration is complete. It takes up to 60 seconds for the W AN Interface to come out of standby and for communications t ...
-
Cabletron Systems WPIM-RT1 - page 37
Fractional T1 Configuration Using PPP WPIM-RT1 User’ s Guide 3-15 The line configuration information sho wn in T able 3-2 must be supplied by the service provider . 3.4.1 T1 Physical Configuration Begin the WPIM-R T1 physical configuration by accessing the W AN Physical Configuration screen through Local Management ( Figure 3-1 ). Proceed wi ...
-
Cabletron Systems WPIM-RT1 - page 38
Chapter 3: Local Management 3-16 WPIM-RT1 User’ s Guide The follo wing four steps are based on information supplied by the service provider . Consult the service provider for the correct settings. 5. Use the arrow keys to highlight T1 Line Coding . Use the SPACE bar to select B8ZS or AMI , then press ENTER. 6. Use the arrow keys to highlight T1 F ...
-
Cabletron Systems WPIM-RT1 - page 39
Frame Relay Configuration WPIM-RT1 User’ s Guide 3-17 3.4.2 T1 Interface Configuration The W AN Interface Configuration screen is accessed through the W AN Physical Configuration screen. Access the W AN Interface Configuration screen by using the arro w keys to highlight the WAN INT CONFIG command and press ENTER. Refer to Figure 3-4 and pro ...
-
Cabletron Systems WPIM-RT1 - page 40
Chapter 3: Local Management 3-18 WPIM-RT1 User’ s Guide The line configuration information sho wn in T able 3-3 must be supplied by the service provider . 3.5.1 Frame Relay Ph ysical Configuration Begin the WPIM-R T1 physical configuration by accessing the W AN Physical Configuration screen through Local Management ( Figure 3-1 ). Proceed wit ...
-
Cabletron Systems WPIM-RT1 - page 41
Frame Relay Configuration WPIM-RT1 User’ s Guide 3-19 3. Insert the interface number (refer to NOTE below) into the timeslot being used. Type the number, press ENTER, then exit this field by using the arrow keys. The cursor automatically moves to the T1 Line Coding field. The next four steps are based on information supplied by the service provi ...
-
Cabletron Systems WPIM-RT1 - page 42
Chapter 3: Local Management 3-20 WPIM-RT1 User’ s Guide 3.5.2 Frame Relay Interface Configuration Access the W AN Interface Configuration screen through the W AN Physical Configuration screen, by using the arrow keys to highlight the WAN INT CONFIG command, then press ENTER. Proceed with the follo wing steps to configure the W AN Interf ace. ...
-
Cabletron Systems WPIM-RT1 - page 43
Frame Relay Configuration WPIM-RT1 User’ s Guide 3-21 The W AN configuration is complete. Communications between the WPIM-R T1 and the service provider’ s switch takes approximately one or two minutes to complete. A status of Inactive displays on a DLCI per DLCI basis by default until both ends of the DLCI are configured correctly . Once bot ...
-
Cabletron Systems WPIM-RT1 - page 44
Chapter 3: Local Management 3-22 WPIM-RT1 User’ s Guide ...
-
Cabletron Systems WPIM-RT1 - page 45
WPIM-RT1 User’ s Guide A-1 APPENDIX A SPECIFICATIONS This appendix provides operating specifications and cabling information for the Cabletron Systems WPIM-R T1. Cabletron Systems reserves the right to change these specifications at any time without notice. A.1 PHYSICAL PR OPERTIES A.2 EN VIR ONMENTAL REQUIREMENTS A.3 REGULATORY COMPLIANCE This ...
-
Cabletron Systems WPIM-RT1 - page 46
Appendix A: Specifications A-2 WPIM-RT1 User’ s Guide A.4 T1 INTERFACE CABLING T able A-1 lists Cabletron Systems part numbers for the interface cables. A standard 20-foot cable is av ailable or the length of cable may be specified when ordering. A.4.1 Cable Assemblies and Pinouts The follo wing section provides connector information for the T1 ...
-
Cabletron Systems WPIM-RT1 - page 47
WPIM-RT1 User’ s Guide B-1 APPENDIX B FCC P ART 68 - USER’ S INFORMATION The follo wing instructions are provided to ensure compliance with the Federal Communications Commission (FCC) Rules, Part 68. 1. This device must only be connected to the ISDN Basic Rate network behind an FCC Part 68 registered channel service unit. Direct connection is n ...
-
Cabletron Systems WPIM-RT1 - page 48
Appendix B: FCC P ar t 68 - User’ s Inf ormation B-2 WPIM-RT1 User’ s Guide 5. Under the FCC Rules, no customer is authorized to repair this equipment. This restriction applies regardless of whether the equipment is in or out of warranty. 6. If the telephone company alters their equipment in a manner that will affect use of this device, they mu ...
-
Cabletron Systems WPIM-RT1 - page 49
FCC Part 68 - User’s Information WPIM-RT1 User’ s Guide B-3 AFFIDAVIT FOR THE CONNECTION OF CUSTOMER EQUIPMENT TO 1.544 MBPS AND/OR SUBRATE DIGITAL SERVICES For the w ork to be performed in the certified territory of T elco’ s name: State of: Country of: I , , o f (Name of Authorized Representati ve) (Customer Name) , (Customer’ s Address) ...
-
Cabletron Systems WPIM-RT1 - page 50
Appendix B: FCC P ar t 68 - User’ s Inf ormation B-4 WPIM-RT1 User’ s Guide I attest that the operator(s) maintainer(s) of the digital CPE responsible for the establishment, maintenance and adjustment of the encoded analog content and billing information has (hav e) been trained to perform these functions by successfully completing one of the f ...
Cabletron Systems WPIM-RT1についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもCabletron Systems WPIM-RT1の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがCabletron Systems WPIM-RT1で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。