-
Paradyne 9161-A2-GN10-40 - page 1
TM 1 9161 Single T1 Network Access Module (NAM) Installation Instructions Document Number 9161-A2-GN10-40 December 1998 Product Documentation on the W orld Wide W eb We provide complete product documentation online. This lets you search the documentation for specific topics and print only what you need, reducing the waste of surplus printing. It al ...
-
Paradyne 9161-A2-GN10-40 - page 2
496-15149 2 Safety Instructions Please read the EMI warning and Important Safety Instructions in the T echnical Reference or in the installation document that you received with your housing. ! HANDLING PRECAUTIONS FOR ST A TIC-SENSITIVE DEVICES This product is designed to protect sensitive components from damage due to electrostatic discharge (ESD) ...
-
Paradyne 9161-A2-GN10-40 - page 3
3 Cables Y ou May Need The following cables and connectors are specifically for this product. See Warranty , Sales, and Service Information on page 15 for ordering information. See the T echnical Reference for all cable pin-out information. If connecting to a . . . Y ou need a . . . T erminal/printer (DB25 interface/connector – EIA-232 connection ...
-
Paradyne 9161-A2-GN10-40 - page 4
NAM Rear Panel SINGLE T1 NAM NET DBM DSX PORT 1 PORT 2 COM NET DBM (For Future Use) DSX Po r t 1 P or t 2 COM 98-15050-03 4 T ools Required A small Phillips screwdriver (#1 or #2) to install the T1 NAM A small, flat-blade screwdriver to install the: — I/O card — Cable connections Installing the I/O Card The NAM’s I/O card provides the ...
-
Paradyne 9161-A2-GN10-40 - page 5
COM SINGLE T1 NAM NET DBM DSX PORT 1 PORT 2 Port 1 98-15054-02 DTE Cable DTE Cable V .35, RS-449, V .1 1/X.21 Adapter Cable DTE DTE Port 2 5 Connecting to the Network 1. Insert the 8-pin connector on the RJ48C network cable into the NET interface. 2. Insert the other end of the cable into the RJ48C modular jack. Connecting to a DTE If the DTE cable ...
-
Paradyne 9161-A2-GN10-40 - page 6
6 Connecting to the DSX 1. Insert the DB15 end of the DSX cable into the DSX interface. 2. Insert the other end of the cable into the CPE (Customer Premises Equipment, such as a PBX). Connecting the COM Port to a User Interface 1. Insert the 8-pin end of the cable into the COM port. 2. Insert the other end of the cable into the user interface (VT10 ...
-
Paradyne 9161-A2-GN10-40 - page 7
7 Installing the T1 NAM In both the 2- and the 5-slot housings, the NAM is always installed in Slot 01. The NAM can be installed in any slot in the access carrier . ! W ARNING: Do NOT remove any jumpers located on the battery . T o do so can cause non-volatile memory loss. Should a jumper become separated from the battery , contact your service rep ...
-
Paradyne 9161-A2-GN10-40 - page 8
8 Removing/Replacing a Card Card removal procedures differ , depending on whether you are removing the card from the front or rear of the housing. If you are r emoving the . . . Then go to . . . NAM Removing/Replacing the NAM . I/O card Removing/Replacing the I/O Card . Removing/Replacing the NAM 1. Remove the housing’s bezel, if applicable. See ...
-
Paradyne 9161-A2-GN10-40 - page 9
2– OK OK ALM TST BKP SIG OOF ALM SIG OOF ALM 1– OK 9161 IN OUT IN OUT IN OUT IN OUT NET DSX NET MON DSX MON NETWORK DSX PORT 496-15051 T est Jacks LEDs 9 Front Panel LEDs and T est Jacks The T1 NAM has 12 LED (light-emitting diode) status indicators and four sets of test jacks. T est Jacks The NAM contains four sets of test jacks. Use these for ...
-
Paradyne 9161-A2-GN10-40 - page 10
10 Network and DSX Interface LEDs Label Indication Color What It Means SIG Signal Green ON – A recoverable signal is present on the network/DSX interface. OFF – The signal cannot be recovered from the network/DSX interface. An LOS condition exists. OOF Out of Frame Y ellow ON – At least one OOF was detected during the sampling period. OFF – ...
-
Paradyne 9161-A2-GN10-40 - page 11
11 T roubleshooting Symptom Possible Cause Solutions No power , or none of the system LEDs are lit. For DC power source, DC power is not present. For AC power source, the wall receptacle has no power , or the housing’s power cord is not securely plugged into the wall receptacle or the back of the housing. Check the DC power source. 1. Check the w ...
-
Paradyne 9161-A2-GN10-40 - page 12
12 T echnical Specifications Specification Criteria Weight T1 NAM T1 I/O card 1 lb. 2 oz. (.51 kg) 6 oz. (.17 kg) Size T1 NAM T1 I/O card 1 1.58 ″ x 8.00 ″ (29.41 cm x 20.32 cm) 2.90 ″ x 10.15 ″ (7.37 cm x 25.78 cm) Power Consumption 9.4 watts, 0.78 amps input current at 12 volts Physical Environment Operating temperature Storage temperatur ...
-
Paradyne 9161-A2-GN10-40 - page 13
13 Specification Criteria DBM (Backup) connector (reserved for future use) One 8-position modular keyed USOC RJ45 jack Clocking Sources T1 network interface, any port, internal clock, DSX-1 T1 interface or external clock Loopbacks Standard Additional Network Line Loopback, Network Payload Loopback, V .54 Loop 2 (DCLB) and V .54 Loop 3 (DTPLB) Netwo ...
-
Paradyne 9161-A2-GN10-40 - page 14
14 DSX Port/Interface Function Circuit Pin # Receive tip from the DTE T1 1 Receive ring from the DTE R1 9 T ransmit tip to the DTE T 3 T ransmit ring to the DTE R 11 Shield – 2,4 DTE Ports/Interfaces Signal Circuit Mnemonic ITU/ CCITT # Dir ection 25-Pin Pin # Shield — — — 1 T ransmitted Data ( TXD ) BA 103 T o DCE 2 (A) 14 (B) Received Dat ...
-
Paradyne 9161-A2-GN10-40 - page 15
15 W arranty , Sales, and Service Information Contact your local sales representative, service representative, or distributor directly for any help needed. For additional information concerning warranty , sales, service, repair , installation, documentation, training, distributor locations, or Paradyne worldwide office locations, use one of the fol ...
Paradyne 9161-A2-GN10-40についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもParadyne 9161-A2-GN10-40の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがParadyne 9161-A2-GN10-40で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。