Bunn H5Mの取扱説明書

20ページ 0.59 mb
ダウンロード

ページに移動 of 20

Summary
  • Bunn H5M - page 1

    H5M 10267.0000D 7/00 © 1988 BUNN-O-MATIC CORPORATION B UNN-O-MA TIC CORPORA TION POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS 62708-3227 PHONE: (217) 529-6601 F AX: (217) 529-6644 BU N N ® OPERA TING & SERVICE MANUAL WARNING Very Hot Water Use With Care! ! DISCONNECT FROM POWER SOURCE BEFORE REMOVAL OF ANY PANEL OR REPLACEMENT OF ANY COMPONENT! ...

  • Bunn H5M - page 2

    2 CONTENTS Introduction ................................................. 2 Warranty ...................................................... 2 User Notices ................................................ 3 Electrical Requirements ............................... 4 Plumbing Requirements .............................. 4 Initial Set-Up ................ ...

  • Bunn H5M - page 3

    3 ...

  • Bunn H5M - page 4

    4 ELECTRICAL REQUIREMENTS CAUTION - The dispenser must be disconnected from the power source until specified in Initial Set-Up. The H5M dispenser requires 2-wire, grounded service rated 120, 208, or 240 volts ac, 20 amp, single phase. The H5MA, 230V-CE dispenser requires 2-wire, grounded service rated 230 volts ac, 40 amp, single phase, 50/ 60Hz . ...

  • Bunn H5M - page 5

    5 INITIAL SET -UP CAUTION - The dispenser must be disconnected from the power source throughout the initial set-up, except when specified in the instructions. 1. Remove the upper rear panel and rotate the control thermostat knob fully counterclockwise to the “ OFF ” position and r eplace the panel. 2. Connect the dispenser to the power source a ...

  • Bunn H5M - page 6

    6 TROUBLESHOOTING A troubleshooting guide is provided to suggest probable causes and remedies for the most likely problems encountered. If the problem remains after exhausting the troubleshooting steps, contact the Bunn-O-Matic T ech- nical Service Department. • Inspection, testing, and repair of electrical equipment should be performed only by q ...

  • Bunn H5M - page 7

    7 TROUBLESHOOTING (cont.) Problem Probable Cause Remedy Automatic refill will not operate after drawing hot water . Water flows into the tank con- tinuously (Dispenser discon- nected from power source). Water flows into the tank con- tinuously (Dispenser connected to power source). Water is cold. 1. No water 2. W ater strainer/flow control 3. Safet ...

  • Bunn H5M - page 8

    8 TROUBLESHOOTING (cont.) Problem Probable Cause Remedy Water boils continuously . Dispenser is making unusual noises. Ready indicator will not light. (when temperature is within 4 ° of its selected setting.) 1. T emperature control 2. Lime build-up 1. Solenoid valve 2. Plumbing lines 3. W ater supply 1. T emperature control 2. Ready Indicator LED ...

  • Bunn H5M - page 9

    9 SERVICE This section provides procedures for testing and replacing various major components used in this dis- penser should service become necessar y . Refer to T roubleshooting for assistance in determining the cause of any problem. Component Access WARNING – Disconnect the dispenser from the power source before the removal of any panel or the ...

  • Bunn H5M - page 10

    10 ...

  • Bunn H5M - page 11

    11 ...

  • Bunn H5M - page 12

    12 SERVICE (cont.) Solenoid Valve Location: The solenoid valve is located inside the rear of the dis- penser on the right side near the bottom. 6. Check the solenoid valve for coil action. Connect the dispenser to the power source. Listen carefully in the vicinity of the solenoid valve for a “ clicking ” sound after approximately 5 seconds, as ...

  • Bunn H5M - page 13

    13 ...

  • Bunn H5M - page 14

    14 FIG. 10 THERMOSTAT WIRING BLU/BLK to Limit Thermostat BLK to T erminal Block P1782 SERVICE (cont.) Thermostat Location: The mechanical thermostat is located inside the upper rear panel. T o test the thermostat, access will also be needed to the terminal block located inside the bottom access panel. T est Pr ocedure: 1. Disconnect the dispenser f ...

  • Bunn H5M - page 15

    15 SERVICE (cont.) Liquid Level Board Location: The liquid level board is located inside the lower panel. Test Procedure: 1. Disconnect the dispenser from the power sour ce. 2. Remove the blue wire from terminal 1 and the pink wire from terminal 4 of the circuit board. 3. Check the voltage across terminals 2 and 3 with a voltmeter . Connect the dis ...

  • Bunn H5M - page 16

    16 15. Move the probe's flat end to the dispenser hous- ing. The indication must be 0. 16. Move the probe's flat end away from the dispenser housing. The indication should again be: a.) 100 to 120 volts ac for 100 to 120 volt models, b.) 200 to 240 volts ac for 200 to 240 volt models, c.) 230 volts ac for 230 volt models. 17. Disconnect t ...

  • Bunn H5M - page 17

    17 Location: The contactor is located on the component bracket inside the lower rear panel. T est Pr ocedures: 1. Disconnect the dispenser from the power sour ce. 2. Disconnect the black wire from the contactor coil to the limit thermostat and black wire from the red wire on the main harness on two wire 240V mod- els. 3. Check the voltage across th ...

  • Bunn H5M - page 18

    18 BLK to left Tank Heater RED to Terminal Block(L2) BLK to Terminal Block (L1) RED to Right Tank Heater BLK to Limit Thermostat RED from Main Harness P1725 FIG.14 CONTACTOR WIRING contactor . Removal and Replacement: 1. Disconnect all the wires from the contactor . 2 . Remove the two #8-32 screws securing the contactor to the contactor mounting br ...

  • Bunn H5M - page 19

    19 4 3 12 LIQUID LEVEL BOARD BLU/BLK TANK HEATER 120 VOLTS A C 2 WIRE SINGLE PHASE 10243.0000D 1/99 © 1987 BUNN-O-MATIC CORPORATION SCHEMATIC WIRING DIAGRAM H5M L1 N BLK BLK BLK SOL WHI GREEN BLU WHI WHI BLK BLK (PROBE) P N K RED RED BLK SW& THERMOSTAT OPTIONAL READY INDICATOR OVERFLOW PROTECTION SWITCH LIMIT THERMOSTAT 4 3 12 LIQUID LEVEL BOA ...

  • Bunn H5M - page 20

    20 WIRING DIAGRAMS 4 3 12 LIQUID LEVEL BOARD BLK SW& THERMOSTAT 10262.0001A 11/99 © 1999 BUNN-O-MATIC CORPORATION SCHEMATIC WIRING DIAGRAM H5MA, 230V CE L1 L2 BLK SOL GREEN BLU BLK BLK (PROBE) P N K RED RED RED BLU/BLK BLK RED-12 BLK-12 N.O. N.O. K RED RED RED TANK HEATER 230 VOLTS A C 2 WIRE SINGLE PHASE OVERFLOW PROTECTION SWITCH LIMIT THERM ...

メーカー Bunn カテゴリー Water Heater

Bunn H5Mのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- H5Mの取扱説明書
- Bunnの製品カード
- パンフレット
- またはBunn H5Mの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Bunn H5Mの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Bunn H5Mの取り付け説明書、サービスマニュアル、簡易説明書、またはBunn H5Mのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Bunn H5Mの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Bunn H5Mデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがBunn H5Mを使用するのを助ける技術的文書のことです。説明書は通常、全てのBunn H5Mユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Bunnの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Bunn H5Mの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははBunn H5Mの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Bunn H5Mに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Bunn H5Mデバイスの基本機能を使うにあたってのヒント。 Bunn H5Mのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Bunn H5Mに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるBunn H5Mのメーカー/サービスへの連絡先に関する情報。

Bunn H5Mについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもBunn H5Mの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがBunn H5Mで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)