Allstar Products Group Gate Operator Standby Power Supplyの取扱説明書

8ページ 0.53 mb
ダウンロード

ページに移動 of 8

Summary
  • Allstar Products Group Gate Operator Standby Power Supply - page 1

    1 INST ALLA TION AND OWNER’S MANUAL MODEL SPS-50 GA TE OPERA T OR ST ANDBY POWER SUPPL Y READ T HIS MANUAL CAREFULLY BEFORE INSTA LLATION OR USE Serial #: Date Installed: Your Dealer: 107887 ...

  • Allstar Products Group Gate Operator Standby Power Supply - page 2

    2 Pre-Installation Notes ....... ................ ............... .............. .......... 3 Installing the SPS-50 ....... ................ ............... ................ .......... 4 LED Indicators ............ ......................................... .......... 5 Electrical Connections ............... ........................... ........ 5 Te ...

  • Allstar Products Group Gate Operator Standby Power Supply - page 3

    3 The Allstar Standb y Power Suppl y is designed to provide back- up power to a gate operator w hen the main AC suppl y voltage is interrupted or disconnected. It el iminates the need for a separate motor and control ci rcuit to be m echanically attached to the gate operator. The SPS- 50 will provide the power and a signal to the gate operator to o ...

  • Allstar Products Group Gate Operator Standby Power Supply - page 4

    4 The follow ing items are include d with the SPS -50: 1. 1- SPS-50 control box 2. 1 - SPS-50 battery pack 3. 1- Relay output wire harness 4. 2- AC po wer in or power out wire harn ess 5. 1- Warning label 6. 1- Instr uctio n Man ual INST A LLING THE SPS-50 The SPS-50 is not w eather proof and must be protected f rom expo sure. Ideally, the unit sho ...

  • Allstar Products Group Gate Operator Standby Power Supply - page 5

    5 Connecting the AC Lin e Voltage (Main Voltage) The SPS-50 is designed to provide back-up po wer to the gate operator ONLY. Aux iliary devices such as loop detectors, card readers, phone entry s ystems, et c., m ust NOT be co nnected to the output of the SPS-50. These devices may overload the capacity of the SPS- 50 and prev ent proper gate operat ...

  • Allstar Products Group Gate Operator Standby Power Supply - page 6

    6 Installing the Warning Labels The warning labels s hould be pl aced to notify service personnel that the gate operator is connected to a back -up power supply unit. Maintenance of Batteries Typical battery life should be two years, however this will vary depending on use and climate. Should batteries need re placing, observe the following: Serv i ...

  • Allstar Products Group Gate Operator Standby Power Supply - page 7

    7 RISK OF ENTRAPMENT. THE SPS-50 IS DESIGNED TO PROVIDE POWE R TO A GATE OPER ATOR WHEN THE MAIN AC POWER I S TURNED OFF. A GATE OPERATOR CONNECTED TO THE SPS-50 MAY START UNEXPECTEDLY WHEN THE MAIN AC POWER IS TURNED OFF. Figure 3: Wiring Diagram 107890 ...

  • Allstar Products Group Gate Operator Standby Power Supply - page 8

    8 INPUT VOLTAGE: 105 - 125 VAC OUTPUT VOLTAGE: 115 VAC ± 10% SURGE PROTECTION: MOV, TRANZORB OUT PUT FREQU ENCY : 60 HZ BATTERY: 24 V DC, 7 AH OUTPUT CURRE NT: 5 AMPS RECH ARG E TIME : 8 HOURS SURGE CURRENT: 9 AMPS OUTPUT POW ER: 500 W ATTS SURGE PO W ER: 1000 W ATTS RELAY OUTPUT: DPDT, 2 AMPS Manufacturer’s Lim ited Warranty Linear LLC warran t ...

メーカー Allstar Products Group カテゴリー Power Supply

Allstar Products Group Gate Operator Standby Power Supplyのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- Gate Operator Standby Power Supplyの取扱説明書
- Allstar Products Groupの製品カード
- パンフレット
- またはAllstar Products Group Gate Operator Standby Power Supplyの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Allstar Products Group Gate Operator Standby Power Supplyの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Allstar Products Group Gate Operator Standby Power Supplyの取り付け説明書、サービスマニュアル、簡易説明書、またはAllstar Products Group Gate Operator Standby Power Supplyのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Allstar Products Group Gate Operator Standby Power Supplyの製品を使用するにあたって最も人気のある説明書を閲覧できます。

Allstar Products Group Gate Operator Standby Power Supplyデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがAllstar Products Group Gate Operator Standby Power Supplyを使用するのを助ける技術的文書のことです。説明書は通常、全てのAllstar Products Group Gate Operator Standby Power Supplyユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Allstar Products Groupの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Allstar Products Group Gate Operator Standby Power Supplyの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははAllstar Products Group Gate Operator Standby Power Supplyの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Allstar Products Group Gate Operator Standby Power Supplyに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Allstar Products Group Gate Operator Standby Power Supplyデバイスの基本機能を使うにあたってのヒント。 Allstar Products Group Gate Operator Standby Power Supplyのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Allstar Products Group Gate Operator Standby Power Supplyに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるAllstar Products Group Gate Operator Standby Power Supplyのメーカー/サービスへの連絡先に関する情報。

Allstar Products Group Gate Operator Standby Power Supplyについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもAllstar Products Group Gate Operator Standby Power Supplyの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがAllstar Products Group Gate Operator Standby Power Supplyで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)