Plinius SA-250の取扱説明書

23ページ 1.12 mb
ダウンロード

ページに移動 of 23

Summary
  • Plinius SA-250 - page 1

    Class A Power Amplifier ...

  • Plinius SA-250 - page 2

    2 ...

  • Plinius SA-250 - page 3

    3 CONGRATULATIONS CONGRATULATIONS CONGRATULATIONS CONGRATULATIONS on your decision to become the proud owner of this Plinius SA-250 Power Amplifier. This manual has been prepared to help you understand the operation of your amplifier, and to provide information about its design and the variety of ways it may be used. We have designed and manufactur ...

  • Plinius SA-250 - page 4

    4 Introduction .................................................................................................................. ......................Page 3 Precautions ................................................................................................................... .....................Page 5 Amplifier Features - FRONT PANEL .. ...

  • Plinius SA-250 - page 5

    5 Please take special note of the following precautions before operating your new amplifier: • The Plinius SA-250 Power Amplifier can be operated in bridged mode and may deliver in excess of 900 watts into 8 ohms. This amplifier is also capable of a very large peak current delivery. • The Plinius SA-250 Power Amplifier operates in Class A. It i ...

  • Plinius SA-250 - page 6

    6 The front of the Plinius SA-250 Power Amplifier incorporates a small panel fitted with three switches. These switches control the functions most used on the amplifier. F RONT P ANEL L AYOUT S HOWING M UTE , M AINS A ND B IAS S WITCHES The operation of these switches is, from the left: MUTE SWITCH It is not recommended practice to interfere with t ...

  • Plinius SA-250 - page 7

    7 BIAS SWITCH This switch on the right of the panel alters the operating bias of the amplifier. The switch operates on a pulse system and lights the Bias LED when the amplifier is switched to Class A. In Class AB the LED is off. BIAS AB: BIAS AB: BIAS AB: BIAS AB: This position reduces the bias on the output stage to operate the amplifier in Class ...

  • Plinius SA-250 - page 8

    8 This panel incorporates all the terminals for connecting the input signals from your preamplifier, and output to the loudspeakers, and mains supply. A reasonable understanding of this amplifier and a logical approach should ensure that you are listening to this amplifier without any difficulties at all. Please remember that your Plinius SA-250 Po ...

  • Plinius SA-250 - page 9

    9 INPUT TERMINALS Input terminals for your Plinius SA-250 Power Amplifier are easily accessible and fitted to the top centre area of the rear panel. A brief summary of connection possibilities is listed below, while a more detailed explanation follows later in this instruction manual. RCA INPUTS LEFT & RIGHT: RCA INPUTS LEFT & RIGHT: RCA IN ...

  • Plinius SA-250 - page 10

    10 RCA BRIDGED MONO: RCA BRIDGED MONO: RCA BRIDGED MONO: RCA BRIDGED MONO: This option configures your amplifier to drive one loudspeaker from one unbalanced signal fed to the RIGHT RCA input. The loudspeaker is connected to both channels positive (+) output terminals, giving an available power in this mode four times the rated output of the amplif ...

  • Plinius SA-250 - page 11

    11 Please note that in order to achieve STEREO performance in either of the Mono modes, it will be necessary to use two Plinius SA-250 Power Amplifiers - one amplifier each for left and right channels. GROUND LIFT SWITCH This switch is located adjacent to the Mains Input Socket, and allows the signal ground to be disconnected from the chassis. In s ...

  • Plinius SA-250 - page 12

    12 PLACEMENT AND VENTILATION Your Plinius SA-250 is designed to operate at a moderately high temperature, even more so when used in Class A. The ideal location is on a rigid stand or floor mounted away from direct contact with any temperature sensitive materials or deep pile carpets. The flow of air around the amplifier should also be kept unimpede ...

  • Plinius SA-250 - page 13

    13 R EAR P ANEL S HOWING L OCATION O F I NPUT /O UTPUT T ERMINALS It is important that you connect your loudspeakers (outputs) and preamplifier (inputs) to the Plinius SA- 250 Power Amplifier correctly to ensure the amplifier is not damaged, and sounds it’s best with your system. Now that you have read and familiarised yourself with the connectio ...

  • Plinius SA-250 - page 14

    14 RCA STEREO Connect your preamplifier or input signal to the two RCA inputs at the top of the amplifier back panel. Make sure you connect the red coded cable to the red RIGHT RCA input and the black (or white) cable to the black LEFT RCA input. Also make sure the RCA connectors are a snug fit and are inserted all the way in. Next connect your lou ...

  • Plinius SA-250 - page 15

    15 Now turn the ACS switch fully clockwise then two positions counter-clockwise so that it is in the XLR Stereo position. It is now safe to switch on your amplifier. XLR BALANCED MONO As with RCA Bridged Mono, this option configures your amplifier to drive one loudspeaker, but from one balanced line input connected to the RIGHT XLR Input. In balanc ...

  • Plinius SA-250 - page 16

    16 PHASING (OR POLARITY) It is important to achieve good stereo imaging in your listening room. By observing the wiring instructions above, each Power Amplifier/loudspeaker combination should be in phase. If you experience poor stereo image and/or a lack of bass, check that the loudspeaker wiring has been connected correctly. We recommend that you ...

  • Plinius SA-250 - page 17

    17 ERROR DETECTION The Plinius SA-250 Power Amplifier has in-built error detection. This will function under the following conditions: • When the amplifier is overdriven/clipped • If any internal fuse is damaged Should either of these circumstances arise the amplifier will disconnect both channels and mute the input. This condition will remain ...

  • Plinius SA-250 - page 18

    18 LED BRIGHTNESS CONTROL Your Plinius SA-250 has an internal LED brightness control that will adjust all three front panel LED’s. A small flat bladed screwdriver can be used to adjust the brightness. The LED brightness control is a small multi turn potentiometer and is located on the front of the main circuit board within the top cavity of the a ...

  • Plinius SA-250 - page 19

    19 Your Plinius SA-250 Power Amplifier is designed for use with high fidelity loudspeakers. It should not be used to operate any other type of appliance or equipment. Choice of loudspeakers is one of personal taste, providing the chosen loudspeakers are suitable for use with your amplifier. Be certain that your loudspeakers can handle most of the r ...

  • Plinius SA-250 - page 20

    20 Class A has always been regarded as the perfect operating mode for audio amplifiers. Many leading amplifier designers and manufacturers world wide recognise that a well designed Class A circuit has inherently lower distortion than any other design. Class A circuit topology is one in which the total current the amplifier is capable of delivering, ...

  • Plinius SA-250 - page 21

    21 250-WATTS RMS PER CHANNEL INTO 8 OHMS. 450-WATTS RMS PER CHANNEL INTO 4 OHMS. BOTH CHANNELS DRIVEN FROM 20Hz TO 20kHz AT 0.05% TOTAL HARMONIC DISTORTION. S B B B B RIDGED RIDGED RIDGED RIDGED O O O O UTPUT UTPUT UTPUT UTPUT : :: : 900 Watts RMS 20Hz to 20kHz into 8 ohms (Mono). S D D D D YNAMIC YNAMIC YNAMIC YNAMIC H H H H EADROOM EADROOM EADROO ...

  • Plinius SA-250 - page 22

    22 ACS (Amplifier Configuration Selector) ......................................................................................... .. Page 9 Balanced Signal ................................................................................................................ ...........Page 10 Bias Class A ............................................... ...

  • Plinius SA-250 - page 23

    23 All operational, technical and descriptive material published here is subject to change at any time without notice. For further product information or queries, please contact us at the address below. PLINIUS PLINIUS PLINIUS PLINIUS products are designed and manufactured by: Audible Technologies Ltd. Audible Technologies Ltd. Audible Technologies ...

メーカー Plinius カテゴリー Stereo Amplifier

Plinius SA-250のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- SA-250の取扱説明書
- Pliniusの製品カード
- パンフレット
- またはPlinius SA-250の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Plinius SA-250の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Plinius SA-250の取り付け説明書、サービスマニュアル、簡易説明書、またはPlinius SA-250のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Plinius SA-250の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Plinius SA-250デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがPlinius SA-250を使用するのを助ける技術的文書のことです。説明書は通常、全てのPlinius SA-250ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Pliniusの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Plinius SA-250の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははPlinius SA-250の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Plinius SA-250に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Plinius SA-250デバイスの基本機能を使うにあたってのヒント。 Plinius SA-250のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Plinius SA-250に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるPlinius SA-250のメーカー/サービスへの連絡先に関する情報。

Plinius SA-250についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもPlinius SA-250の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPlinius SA-250で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)