日本語 dropdown-ico

Ultra Start 42xxの取扱説明書

24ページ 1.48 mb
ダウンロード

ページに移動 of 24

Summary
  • Ultra Start 42xx - page 1

    Co v er s All 42xx and 43xx Series R emote Star ter/Alar ms -The system must be placed into Service Mode before any service work is started on the vehicle. It is the sole responsibility of the vehicle owner to ensure that this is done. The manufacturer accepts no liability or responsibility for accidental starting of the vehicle. - CARBON MONOXIDE ...

  • Ultra Start 42xx - page 2

    T able of Contents Page 2 Pre-Insta llation Page 3 Components Feature List Pre-Installation Insta llation Procedures Page 4 Wiring Diagrams Page 5-7 Wire Description Page 8-9 6 Pin Connector Auxiliary Connectors Optional Connectors Jumper Positions Quick S ta rt Insta llation Page 10 Basic Installation Plug-in The Module Manual T ransmission V ehic ...

  • Ultra Start 42xx - page 3

    R ecommended Pre-Installation Procedure s F ea ture List - Control module - 2way LCD and 1way transmitters - Antenna with built in - 6 pin main harness with dual - Program Button and LED’s 30 amp power inputs. - Multi-tone Siren - 1 1 pin harness** - 14 pin harness* - 4 pin harness** - 3 pin keyless entry harness - 2 pin Harness (4350 and L T Mod ...

  • Ultra Start 42xx - page 4

    R ecommended Installation Procedures Under Hood Connections - Route the hood pin and tach wire through the firewall into the engine compartment. If possible route the wires through a factory rubber grommet. If drilling a hole through the firewall, BE CAREFUL . Always check for obstructions on both sides of the firewall. After drilling, use a snap i ...

  • Ultra Start 42xx - page 5

    Wiring Diagram - 1 1 pin + 4 pin Connectors BLUE GREEN RED RED YELLOW Starter Output Heater/Acc Output Power Input Ignition Output Selectable Output Power Input 30amp Output 30amp Output 30amp Input 30amp Input 30amp Output 30amp Output * These connections are for manual transmission vehicles only! “M” models must always be installed into manua ...

  • Ultra Start 42xx - page 6

    Wiring Diagram 14 pin connector BLUE GREEN RED RED YELLOW 1 5 3 2 4 6 Starter Output Heater/Acc Output Power Input Ignition Output Selectable Output Power Input 30amp Output 30amp Output 30amp Input 30amp Input 30amp Output 30amp Output Factory Re-arm Output Starter kill & Anti-Grind Output Factory Disarm Output T runk Release Output (+) Siren ...

  • Ultra Start 42xx - page 7

    W iring Dia gr am auxiliar y connector s Door lock output Door unlock output (-) When Running Low Current (-) Output Low Current (+) Output Door lock module output only* ACTIVE RF ANTENNA** (-) 500ma Output (-) 250ma Output (-) 250ma Output (-) 500ma Output (+) 500ma Output 12 3 The jumpers control the output from the WHITE wire on the 6- pin harne ...

  • Ultra Start 42xx - page 8

    6 Pin P o wer Connector 6-pin Description T est For Wire 1-Y ellow 30amp S t arter Output - This wire will test 0volts in off, accessory and in the ignition position.12volts during st art only . 2-Green 30amp Heat/Acc Output - This wire will test 0volt s in the off position 12- 14volts in the accessory and run positions and 0 volts during start 3-R ...

  • Ultra Start 42xx - page 9

    Auxiliar y Connectors - continued from previous pag e 1 1-Black Ground - System Chassis Ground Input. 12-Blue Glow Plug - Diesel Glow plug input, detects both 12volt and negative glow plug signals. Programmable input. See Menu 3. 13-Blue/White T ach - A/C T ach Signal Input. Used to detect when the vehicle has started. This wire is connected to the ...

  • Ultra Start 42xx - page 10

    Step 1 - Connect All Of the F ollowing W ires 6 Pin P ow er Connector Y ellow 30amp St arter Output - 12volt s during start position only . Green 3 0amp Heater Output - 12volt s in the accessory position off during start and 12volts during run. Red 30amp Power Input - Constant 12volt power at ignition harness or battery . Red 30amp Power Input - Co ...

  • Ultra Start 42xx - page 11

    Manual T ra nsmission “M” Models Never install an automatic transmission remote starter into a manual transmission vehicle!!! Doing so may result in serious injury or death. Do not install remote starters in convertible vehicles! The following wires must be connected In addition to the basic remote starter installation. Park Brake Input- This w ...

  • Ultra Start 42xx - page 12

    Auto T ac h Learn 1) T urn the ignition key to the “ON” position. (The park light s will turn on*). 2) S tart the vehicle with the key , The LEDs on the antenna will turn on if a proper t ach signal is detected**, then after 30-35 seconds the p ark lights will flash and the siren will chirp twice to confirm T ach Learn. * If the park lights do ...

  • Ultra Start 42xx - page 13

    Impor tant T ac h Notes T ach Learning the remote starter is one of the most import ant steps in the installation process. Do not tach learn vehicle while the engine is in high idle. T o ensure the best possible tach setting, ensure that the vehicle is at low idle/ normal operating RPM. V ehicles such as T oyota and Honda may idle much higher when ...

  • Ultra Start 42xx - page 14

    Entering Pro gra m Mode 1) With the ignition in the OFF position, turn the ignition key from “Of f” to “On” 3 times, ON-OFF-ON-OFF-ON within three seconds. (Leave the key in the ON position) 2) Press and release the Program Button located on the antenna. The park light s will flash and the siren will chirp to confirm entering program mode. ...

  • Ultra Start 42xx - page 15

    Quic k View Progr amming * See the following p ages for more detailed programming instructions. Menu 1 - Press Lock 1 Flash 2 Flashes 3 Flashes 1 Ignition Lock Enabled Lock Only Disabled 2 Siren Chirp T ype 1 T ype 2 All Chirp s 3 Lock&Unlock Options Double Unlock 3 second .75 second 4 Unlock/Disarm 125ms 750ms 5. Passive Locks Enable Disable 6 ...

  • Ultra Start 42xx - page 16

    Menu 1- User Settings Ignition ON-OFF-ON-OFF-ON Press & Release Program Button Press Button #1 (Lock) Setting 1 Ignition Auto Lock 1) Ignition Lock & Unlock Enable 1 Flash/Chirp Doors Lock/Unlock with Ignition key . 2) Ignition Lock Only 2 Flashes/Chirps Doors Lock when ignition is turned ON only . *3) Ignition Auto Lock Disable 3 Flashes/C ...

  • Ultra Start 42xx - page 17

    Menu 1- User Settings.. . continued from pr e vious pa ge Setting 6 Sensor Enable/Disable 1) Sensor Disabled 1 Flash/Chirp Imp act Sensor Disabled *2) Sensor Enabled 2 Flashes/Chirps Imp act Sensor Enabled Press & Release the Program Button 6 Times (Setting 6) Confirmed with 6 LED flashes. Press & Hold the Program Button until the appropria ...

  • Ultra Start 42xx - page 18

    Menu 2- Additional Settings ...continued fr om previous page. Menu 3- Star ter Settings Ignition ON-OFF-ON-OFF-ON Press & Release Program Button Press Button #3 (St art) Setting 1 S pecial Door Lock/Unlock Operations (Factory Alarm Rearm) . 1) T ype 1 1 Flash/chirp Unlock pulse before start. Lock pulse af ter start and on shut down. 2) T ype 2 ...

  • Ultra Start 42xx - page 19

    Menu 3- Start er Settings - Continued F r om Prev ious Page Setting 2 With 14pin Connector- Gas/Diesel Mode (Auxiliary Connector Pin 12) 1) (-) Input 1 Flash/chirp (-) Glow Plug input. W aits maximum 30 seconds then start s. 2) T ime Delay 2 Flashes/chirps W aits for approximately 15 seconds then remote st arts. *3) Gas/ (+) Input 3 Flashes/chirp s ...

  • Ultra Start 42xx - page 20

    Menu 4- T ac h Settings Ignition ON-OFF-ON-OFF-ON Press & Release Program Button Press Button #4 Setting 1- Auto T ach Learn 1) Perform a System Reset. See p age 15. 2) T urn the ignition key on. (Park lights will turn on). 3) S tart the vehicle, t he LEDs on the antenna will come on when a proper tach signal is detected*. 4) After approximatel ...

  • Ultra Start 42xx - page 21

    T r ansmitter Pr ogr amming Ste p 1 - Within 3 seconds turn the ignition ON-OFF-ON-OFF-ON - Leaving Key ON Ste p 2 - Press and hold the Program Button - The park light s will turn ON and the siren will chirp once.* Continue to hold the Program Button , the park light s will turn off and the siren will chirp 5 times quickly . Ste p 3 - While holding ...

  • Ultra Start 42xx - page 22

    87 86 85 87a 30 87 86 85 87a 30 Lock Un lock V ehicle Lock/Unlock Switch T o Control Relay or Actuator Green Fused +12V Blue Ground Neg a tiv e T ype Door Locks 250ma Neg a tiv e Door Loc ks (More T h an 250ma) P ositiv e T ype Door Loc ks Note: When installing relays always use a fused power source. Blue Green Lock Un lock V ehicle Lock/Unlock Swi ...

  • Ultra Start 42xx - page 23

    87 86 85 87a 30 87 86 85 87a 30 Blue Green Lock Un lock V ehicle Lock/Unlock Switch To Actuator Fused +12V x x Cut Cut 87 86 85 87a 30 Ground DIAGN OSTICS 13 87 86 85 87a 30 87 86 85 87a 30 Blue Green Lock Un lock T o V acuum Pump Fused +12V x Cut Ground Page 23 2WAY REMOTE S T ARTER/ALARM INST ALLATION MANUAL 5 Wi re / R e v erse P olarity T ype D ...

  • Ultra Start 42xx - page 24

    DIA GNOSTICS If the remote starter does not activate when the st art button is pressed the park light s will flash a diagnostic to indicate what shutdown input has been triggered. For example when the start button is pressed the p ark lights flash 3 times slowly . Looking at the chart below this would indicate that the system is in Service Mode, si ...

メーカー Ultra Start カテゴリー Automobile Alarm

Ultra Start 42xxのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 42xxの取扱説明書
- Ultra Startの製品カード
- パンフレット
- またはUltra Start 42xxの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Ultra Start 42xxの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Ultra Start 42xxの取り付け説明書、サービスマニュアル、簡易説明書、またはUltra Start 42xxのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Ultra Start 42xxの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Ultra Start 42xxデバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがUltra Start 42xxを使用するのを助ける技術的文書のことです。説明書は通常、全てのUltra Start 42xxユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Ultra Startの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Ultra Start 42xxの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははUltra Start 42xxの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Ultra Start 42xxに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Ultra Start 42xxデバイスの基本機能を使うにあたってのヒント。 Ultra Start 42xxのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Ultra Start 42xxに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるUltra Start 42xxのメーカー/サービスへの連絡先に関する情報。

Ultra Start 42xxについてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもUltra Start 42xxの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがUltra Start 42xxで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (1)

carlo

in italiano