Toro 2010の取扱説明書

16ページ 0.53 mb
ダウンロード

ページに移動 of 16

Summary
  • Toro 2010 - page 1

    Introduction The Field Interface Unit (FIU) provides the communications hardware link between the SitePro TM central computer , the SitePro compatible field satellite controllers and the SitePro Central Decoder System components. The FIU is available in four configu- rations to provide various combinations of wireline and radio communication paths. ...

  • Toro 2010 - page 2

    6 5 5 7 15 8 9 10 11 13 16 14 17 18 20 12 19 22 21 23 24 1 2 3 4 Figure 2 - Model 2020 (two wireline ports) 1 - Central Computer 2 - Field Interface Unit 3 - COM Port 1 4 - COM Port 2 5 - DB-9/DB-9 Serial Cable 6 - Power Adapter 7 - Auxiliary Port (optional for sensors) 8 - Channel 2 (in) 9 - Channel 1 (in) 10 - 12 V d.c. Power Jack 1 1 - 1.5A Fuse ...

  • Toro 2010 - page 3

    3 6 7 13 8 9 10 11 14 15 16 18 17 19 1 2 12 20 3 5 5 4 21 24 23 25 26 22 1 - Central Computer 2 - Field Interface Unit 3 - COM Port 1 4 - COM Port 2 5 - DB-9/DB-9 Serial Cable 6 - Power Adapter 7 - Auxiliary Port (optional for sensors) 8 - Channel 3 (in) 9 - Channel 1 (in) 10 - 12 V d.c. Power Jack 1 1 - 1.5A Fuse 12 - COM Line 1 13 - RJ1 1 Modular ...

  • Toro 2010 - page 4

    7 8 19 17 9 10 12 11 13 20 21 22 24 23 25 27 26 28 1 2 6 6 6 18 14 16 3 4 5 15 31 30 32 33 29 1 - Central Computer 2 - Field Interface Unit 3 - COM Port 1 4 - COM Port 2 5 - COM Port 3 6 - DB-9/DB-9 Serial Cable 7 - Power Adapter 8 - Auxiliary Port (optional for sensors) 9 - Channel 3 (in) 10 - Channel 2 (in) 1 1 - Channel 1 (in) 12 - 12 V d.c. 13 ...

  • Toro 2010 - page 5

    Installing the Field Interface Unit, W all Plate Assembly and Sur ge Protection Unit 1. Position the Field Interface Unit within 6' (1.8 m) of the PC. Note: Maximum distance is 50' (15.2 m). 2. Using the serial cable(s) supplied, connect the PC to the FIU as illustrated in the appropriate configuration diagram Figure 1–5 . 3. Note: The ...

  • Toro 2010 - page 6

    7. A 25' (7.6 m) length interface cable is supplied for the connection of the modular wall plate to the SPU. Select an installa- tion site for the SPU on an outside wall, within the cable reach, and 3' to 5' (0.9 m to 1.5 m) above ground level for straight and easy access to an earth ground. Attach the SPU securely to the wall using ...

  • Toro 2010 - page 7

    Procedure 1. Drive a 5/8" (16 mm) by 8' (2.5 cm) copper-clad steel ground rod into well-moistened soil not more than 8' (2.5 cm) from the SPU. The top of the ground rod should be 12" (30.5 cm) below grade level. 2. Install 3/4" (19 mm) conduit from the bottom of the SPU enclosure to approximately 12" (30.5 cm) below gr ...

  • Toro 2010 - page 8

    Communication Cab le T est Correct installation of the communication cable is essential for proper operation of the wireline control system. The communi- cation cable must be tested for the presence of significant voltage, circuit continuity and excessive resistance. A digital mult i- meter and a 620 ohm resistor are required to perform the followi ...

  • Toro 2010 - page 9

    Processor Read y: Indicator light will illuminate when the microprocessor in the FIU has received configuration instructions from PC and is ready to communicate with satellites or DIUs. Field T ransmit: Indicator light will illuminate or flash during transmission of data to field satellites or DIU(s). Field Receive/Busy: Indicator light will illumi ...

  • Toro 2010 - page 10

    Note: The Motorola radio service software screens shown in Figure 12 , 13 , and 14 are for example only . Later service software versions may not be formatted as shown, however , the items within boxes must be set as indicated to enable system operation. Radio Components Connection 1. Using the cables provided in the kit, connect the radio, power s ...

  • Toro 2010 - page 11

    Radio-Link System Setup 1. Reconnect power to the FIU and switch on all components. The central computer should be booted up and the SitePro pro- gram operational. See Figure 3 and 4 respectively for hardware configuration of model FIU-201 1 and FIU-2021. 2. From the SitePro program menu bar , select: Setup> Hardware. 3 From the “ System ” t ...

  • Toro 2010 - page 12

    SitePro Central Decoder System Connection The SitePro Central Decoder System (CDS) program works in conjunction with the SitePro Field Interface Unit Model 2010 and the Decoder Interface Unit (DIU). Connect the FIU, central computer , SPU and the DIU(s) as shown in Figure 16 . All hardware is provided for connection except shielded, twisted-pair co ...

  • Toro 2010 - page 13

    4 5 6 6 5 4 2 7 Pin 2 Pin 2 Pin 1 Pin 1 2 3 3 1 Figure 16 - DIU Connection Overview Figure 17 RJ45 Cable to Wall Plate 13 Y ellow Y ellow Y ellow Gray Gray Gray 1 - Surge Protection Unit 2 - Communication Cable 3 - Duplex Conduit Box 4 - RJ45 Modular W all Plate Assembly 5 - RJ45 Modular Cable 6 - Decoder Interface Unit 7 - 620 Ohm Resistor ...

  • Toro 2010 - page 14

    14 Figure 18 - Illustrated Parts Listing, FIU Models 2010, 2020, 201 1 and 2021 See Detail B See Detail C Detail B Detail C Phone Jack View A-A (Bottom View of Item 9) A A ...

  • Toro 2010 - page 15

    15 Item No. P ar t No. Description Quantity P er Assy . Refer to Figure 18 for the f ollowing items: 1 - - - - - - - Housing, SNCX, FIU 1 2 - - - - - - - Bracket, FIU (See Service Item 102-0867) 1 3 - - - - - - - Front Plate, LED Display (See Service Item 102-0872) 1 4 360-0750 Holder , Fuse 1 5 360-0749 Fuse, 1.5 Amp, (10-pack) 1 6 - - - - - - - R ...

  • Toro 2010 - page 16

    T roubleshooting If a malfunction occurs, follow the suggested steps to identify and fix the problem. If the problem cannot be resolved there may be a problem with the FIU, the satellite or the DIU. If you have current NSN support, please call T oro NSN at 1-800-527- 4248. Otherwise, please call our T oro Help Line , 1-800-664-4740 Monday through F ...

メーカー Toro カテゴリー Network Router

Toro 2010のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 2010の取扱説明書
- Toroの製品カード
- パンフレット
- またはToro 2010の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Toro 2010の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Toro 2010の取り付け説明書、サービスマニュアル、簡易説明書、またはToro 2010のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Toro 2010の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Toro 2010デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがToro 2010を使用するのを助ける技術的文書のことです。説明書は通常、全てのToro 2010ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Toroの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Toro 2010の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははToro 2010の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Toro 2010に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Toro 2010デバイスの基本機能を使うにあたってのヒント。 Toro 2010のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Toro 2010に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるToro 2010のメーカー/サービスへの連絡先に関する情報。

Toro 2010についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもToro 2010の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがToro 2010で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)