CLO Systems TP150Bの取扱説明書

29ページ 2.12 mb
ダウンロード

ページに移動 of 29

Summary
  • CLO Systems TP150B - page 1

    CLO SYSTEMS, LLC 1501 W . Cameron Ave., Suite 215, W est Covina, California 91790 T (626) 939-4226 / F (626) 939-3378 WWW .CLOSYSTEMS.COM AUT OMA TED TIL T MOUNTING SYSTEM MANUAL FOR MODEL NUMBERS: TP150B AND TC105B 1 ...

  • CLO Systems TP150B - page 2

    CAUTION: When using this automated tilt mounting system, basic precautions should always be followed, including: • Follow the entire installation/user ’s manual and the important safety instructions before attempting to install or use this mounting system. • Manufacturer is not liable for damage or injury caused by incorrect mounting, assembl ...

  • CLO Systems TP150B - page 3

    Supplied Parts and Hardware Before starting assembly , verify all parts are included and undamaged. If any parts are missing or damaged, do not return the item to your dealer; contact the customer service number listed on the cover page 1. Never use damaged parts! Hardware and procedures for multiple mounting configurations are included. When you s ...

  • CLO Systems TP150B - page 4

    [01] x 1 [02] x 1 [05] x 1 [06] x 1 [08] x 1 [07] x 1 [04] x 1 [03] x 1 [09] x 1 [10] x 1 [11] x 1 M4 x 12 mm M5 x 12mm M6 x 12 mm M8 x 16 mm M4 x 30mm M5 x 30mm M6 x 35mm M8 x 40mm M4 M5 M6 M8 M4 / M5 M6 / M8 M4 / M5 M6 / M8 5/16 in. [18] x 4 [17] x 4 [16] x 4 [15] x 4 [14] x 6 [13] x 6 [12] x 6 [22] x 4 [21] x 4 [20] x 4 [19] x 4 [26] x 4 [25] x ...

  • CLO Systems TP150B - page 5

    (2.5 in.) 6.35 cm [13] [12] 3/16 in. 5 mm 1.0 5 30.4 ~ 61.0 cm (12 ~ 24 in.) ...

  • CLO Systems TP150B - page 6

    1.0. Wood Stud W all Mounting Applications CAUTION: This product is not designed for use in metal stud walls. Do not over tighten the lag bolts [12]. T ighten the lag bolts only until they are firmly against the wall brackets [01]. Mount the wall bracket [01] to at least two (2) wooden studs spaced a minimum of 12 in. (30.4 cm) to a maximum of 24 i ...

  • CLO Systems TP150B - page 7

    [13] [12] [14] 1/2 in. 13 mm 1.1 >46 cm (18 in.) >15 cm (6 in.) [14] >15 cm (6 in.) >30 cm (12 in.) >30 cm (12 in.) >15 cm (6 in.) >64 m m (2.5 in.) 7 ...

  • CLO Systems TP150B - page 8

    1.1. Solid Concrete W all Mounting Applications CAUTION: Make sure concrete anchors [14] are seated flush with concrete surface. The gypsum drywall, lath, plaster , and the like covering may not exceed 1/2 in. (12.7 mm) thickness. CAUTION: Do not over tighten the lag bolts [12]. T ighten the lag bolts only until they are firmly against the wall bra ...

  • CLO Systems TP150B - page 9

    2.0 <=800 mm (31.5 in.) [02] [03] [04] 9 TP150B > 38.1 mm (1.5 in.) > 38.1 mm (1.5 in.) Digital optical audio output [29, 30] [23, 24, 25, 26] [15, 16, 17, 18] ...

  • CLO Systems TP150B - page 10

    2.0. Mounting TV with a flat back Note: The plastic cover (shown in dotted lines) is only provided on model number TP150B; but NOT on model number TC105B. The pin [04] is shipped pre-inserted into the “STORE” opening on the bracket [03]. Note: Most flat screen TVs are provided with Digital Optical Audio Output on the back of the TV . If your TV ...

  • CLO Systems TP150B - page 11

    2.1 <=800 mm (31.5 in.) 11 [02] [03] TP150B Digital optical audio output > 38.1 mm (1.5 in.) > 38.1 mm (1.5 in.) OPT [27, 28] [29] [29, 30] [23, 24, 25, 26] [19, 20, 21, 22] [04] ...

  • CLO Systems TP150B - page 12

    2.1. Mounting TV with a curved back or obstruction Note: The plastic cover (shown in dotted lines) is only provided on model number TP150B; but NOT on model number TC105B. Note: Most flat screen TVs are provided with Digital Optical Audio Output on the back of the TV . If your TV has one, locate the Digital Optical Audio Output – as this will be ...

  • CLO Systems TP150B - page 13

    3.0 13 ...

  • CLO Systems TP150B - page 14

    3.0. Hang TV onto the wall bracket Y ou may need assistance with lifting the TV . Remove the two screws on the bottom of the two brackets [02] and [03], and save these screws as they will be used in the following steps. Hang the two brackets [02] and [03] to the wall bracket [01]. Reinsert and tighten the bottom two screws to anchor the motorized b ...

  • CLO Systems TP150B - page 15

    4.0 [03] [02] [06] [07] [08] 15 ...

  • CLO Systems TP150B - page 16

    4.0. Electrical Connections Note: Select the right electrical prong [09, 10, or 1 1] for your electrical socket. (1) Refer to Section 9.0 and manually tilt the TV up, and insert the pin [04] to the “UP” opening to hold the TV up for easier electrical connections. (2) Insert the AC adapter jack [06] into the control box, and plug in the electric ...

  • CLO Systems TP150B - page 17

    5.0 13 ~ ~ 17 ...

  • CLO Systems TP150B - page 18

    5.0. Adjusting the Tilt Note: Section 5.0 only applies to Model Number TP150B. For Model Number TC105B, skip this Section and go to the Section 7.0 (1) Use the down arrow button ( ) on the remote control [05] to fully tilt down the TV . Refer to Section 9.0. (2) The mounting system is design to tilt the TV down maximum of 13º. Note: the maximum ti ...

  • CLO Systems TP150B - page 19

    6.0 [03] 19 ...

  • CLO Systems TP150B - page 20

    6.0. Removing the spring to tilt the TV down fully Make sure the TV is in the upright position before proceeding with these steps! (1) If the TV is not in the upright position, then use the up arrow button ( ) on the remote control [05] to tilt up the TV . (2) Remove the two screws to take of the plastic cover off on the non-motorized bracket [03]. ...

  • CLO Systems TP150B - page 21

    7.0 OPT 2 [02] 21 ...

  • CLO Systems TP150B - page 22

    7.0. Optional: Adjusting the upright position of the TV If desired, adjust the upright position of the TV by ± 2º by turning the bottom screw on the motorized bracket [02]. 22 ...

  • CLO Systems TP150B - page 23

    8.0 STORE UP P2 P1 STORE UP P2 P1 [03] [04] STORE UP P2 P1 23 ...

  • CLO Systems TP150B - page 24

    8.0. Setting the preset position Note: The pin [04] is shipped from the factory in the “STORE” opening. (1) Insert the pin [04] into the “P1” opening for maximum preset tilt of about 6º. (2) Insert the pin [04] into the “P2” opening for maximum preset tilt of about 9º. (3) Insert the pin [04] into the “STORE” opening for full 13º ...

  • CLO Systems TP150B - page 25

    9.0 25 ...

  • CLO Systems TP150B - page 26

    Remote Control Buttons Function Description Up Key ( ) T ilts the TV up. Down Key ( ) T ilts the TV down to a maximum of 13º. STOP Stops the movement. AUTO The factory default setting is Auto-Mode. If your TV is provided with a Digital Optical Audio Output, and the optical cable [08] has been installed as instructed in Section 4.0, then the Auto-M ...

  • CLO Systems TP150B - page 27

    T roubleshooting 1. TV does not fully tilt down: a. Possible cause: The mounting system relies on the weight of TV to tilt down the TV . Check to see if there is any foreign object such as wire and cable stopping the TV from tilting down. If so, remove or relocate the foreign object. Refer to Section 4.0. b. Possible cause: The spring may be holdin ...

  • CLO Systems TP150B - page 28

    W arranty CLO Systems, LLC warrants its products, under normal use, to be free from defects in material and workmanship for a period of one year from the date of purchase. W arranty covers parts only , and it does not cover labor . Thereafter , repairs will be made at established factory prices. Unauthorized service or repairs by anyone other than ...

  • CLO Systems TP150B - page 29

    Disclaimer CLO Systems, LLC makes no claim that the information contained herein covers all details, conditions, or variations. Nor does it provide for every possible contingency in connection with the installation or use of this mounting system. The information contained in this document is subject to change without notice or obligation of any kin ...

メーカー CLO Systems カテゴリー Indoor Furnishings

CLO Systems TP150Bのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- TP150Bの取扱説明書
- CLO Systemsの製品カード
- パンフレット
- またはCLO Systems TP150Bの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、CLO Systems TP150Bの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、CLO Systems TP150Bの取り付け説明書、サービスマニュアル、簡易説明書、またはCLO Systems TP150Bのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、CLO Systems TP150Bの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

CLO Systems TP150Bデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがCLO Systems TP150Bを使用するのを助ける技術的文書のことです。説明書は通常、全てのCLO Systems TP150Bユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

CLO Systemsの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. CLO Systems TP150Bの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははCLO Systems TP150Bの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。CLO Systems TP150Bに関してこのドキュメントで見つけることができる全てのヒントの目次
3. CLO Systems TP150Bデバイスの基本機能を使うにあたってのヒント。 CLO Systems TP150Bのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。CLO Systems TP150Bに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるCLO Systems TP150Bのメーカー/サービスへの連絡先に関する情報。

CLO Systems TP150Bについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもCLO Systems TP150Bの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがCLO Systems TP150Bで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)