Patton electronic 2707/Iの取扱説明書

24ページ 0.51 mb
ダウンロード

ページに移動 of 24

Summary
  • Patton electronic 2707/I - page 1

    USER MANUAL MODEL 2707/I G.703 NTU with 10Base-T Ethernet Interface SALES OFFICE (301) 975-1000 TECHNICAL SUPPOR T (301) 975-1007 P ar t# 07M2707I Doc# 08625U2-001 Rev . B Revised 6/30/06 An ISO-9001 ...

  • Patton electronic 2707/I - page 2

    2 1.0 Warranty Information ................................................................. 4 1.1 Radio and TV Interference ............................................................ 4 1.2 CE Notice ...................................................................................... 4 1.3 Service ............................................... ...

  • Patton electronic 2707/I - page 3

    3 B.9 Diagnostics ................................................................................. 21 B.10 Indicators .................................................................................... 21 B.11 Configuration .............................................................................. 21 B.12 Power Supply ........................ ...

  • Patton electronic 2707/I - page 4

    4 1.0 W ARRANTY INFORMATION P atton Electronics warrants all Model 2707/I components to be free from def ects, and will—at our option—repair or replace the product should it f ail within one year from the first date of shipment. This warranty is limited to def ects in w orkmanship or mater ials, and does not cov er customer damage, ab use , or ...

  • Patton electronic 2707/I - page 5

    5 als A uthorization number on the outside of the shipping container . This number ma y be obtained from Patton Electronics T echnical Ser vices at: • T el: +1 (301) 975-1007 • Email: support@patton.com • URL: http://www .patton.com Note P ackages received without an RMA number will not be accepted. Caution This device is not intended to be c ...

  • Patton electronic 2707/I - page 6

    6 2.0 GENERAL INFORMATION Thank you f or your purchase of this P atton Electronics product. This product has been thoroughly inspected and tested and is warranted f or One Y ear par ts and labor . If any questions or problems arise during installation or use of this product, please do not hesitate to contact P at- ton Electronics T echnical Suppor ...

  • Patton electronic 2707/I - page 7

    7 3.0 PPP OPERATIONAL BACKGR OUND PPP is a protocol used f or multi-ple xed transport over a point-to-point link. PPP operates on all full duple x media, and is a symmetr ic peer-to- peer protocol, which can be divided into the f ollowing main components: • A standard method to encapsulate datagrams o v er serial links • A Link Control Protocol ...

  • Patton electronic 2707/I - page 8

    8 Figure 1. Cisco router with serial interface, configured as PPP Half Bridge. Figure 1 shows a typical Cisco router with a serial interf ace configured as a PPP Half Bridge. The router ser ial interf ace connects to the W AN via a 2707/C (V .35) E1 NTU and to the remote 2707/I with suppor t for PPP bridging. The 2707/I functions as a node on the ...

  • Patton electronic 2707/I - page 9

    9 4.0 CONFIGURATION The Model 2707/I f eatures configuration capability via hardware DIP s witches. This section describes all possible DIP s witch configurations of the Model 2707/I. 4.1 DIP SWITCH CONFIGURATIONS The Model 2707/I has an internal DIP switch that enables configur ation f or a wide range of applications. The DIP switch is accessed ...

  • Patton electronic 2707/I - page 10

    10 Switch S1 settings T able 1 sho ws the settings f or DIP s witch S1-1 thru S1-8. SW1-1 Line Coding: HDB3 (default) Use Switch SW1-1 to control the Network Line Coding options. Set these options to be the same as the Line Coding given to y ou by your Service Provider . If you are using tw o Model 2707/Is together as shor t range modems, set both ...

  • Patton electronic 2707/I - page 11

    11 The receiver recogniz es these special violations and decodes them as zeros . This method enables the network to meet minimum pulse den- sity requirements. Unless AMI is required in your application, HDB3 should be used whene ver possib le. • AMI . Alter nate Mark Inv ersion defines a pulse as a "mark, ” a binary one, as opposed to a z ...

  • Patton electronic 2707/I - page 12

    12 5.0 INSTALLATION Once the Model 2707/I is properly configured, it is ready to connect to the G.703 interf ace, to the Ethernet por t, and to the power source. This section describes how to make these connections . 5.1 CONNECTING TO THE G.703 NETWORK AND ETHERNET LAN This section describes installing the G.703 (75-ohm and 120-ohm), Ethernet LAN, ...

  • Patton electronic 2707/I - page 13

    13 Connecting Dual Coaxial Cable (75 ohm) to the G.703 Netw ork Ref er to Figure 5 to make the proper connections . Figure 5. Rear panel, showing location of connectors Note The outer conductor of the coax cables are isolated from system ear th ground. When using the 75-ohm interf ace, jumper straps JP2, JP5, JP6, and JP7 must be installed ov er th ...

  • Patton electronic 2707/I - page 14

    14 Connecting the T wisted Pair (120 ohm) to the G.703 Network Ref er to the pinout and signals chart in Figure 6 to connect the 120-ohm G.703 network channel. Figure 6. G.703 120-ohm connection. Connecting the 10Base-T Ethernet por t to a PC (DTE) T o connect the Model 2707/I to another DTE device such as a 10Base-T network interface card, constru ...

  • Patton electronic 2707/I - page 15

    15 Figure 8. 10Base-T cross-ov er cable connection Connecting the 10Base-T Ethernet P or t to a Hub The 10Base-T interf ace is configured as DTE (data terminal equipment), just like a 10Base-T netw ork interface card in a PC . Theref ore, it “e xpects” to connect to a 10Base-T Hub using a straight-through RJ-45 cable . Ref er to Figure 9 below ...

  • Patton electronic 2707/I - page 16

    16 DC Power . The 36–60 VDC DC-to-DC adapter supplied with the DC ver- sion of the Model 2707/I plugs in a DC source (nominal 48 VDC) and plugs into the barrel power supply jac k on the rear of the 2707/I. Refer to Figure 10 to make the proper connection. Figure 10. Connecting DC power to the 2707/I DC po wer supply T o power supply jack T o -48 ...

  • Patton electronic 2707/I - page 17

    17 6.0 OPERATION When the Model 2707/I has been properly configured and installed, it should operate transparently . This section descr ibes power-up , LED sta- tus monitors, and the b uilt-in loopback test modes . 6.1 POWER-UP Bef ore applying power to the Model 2707/I, please re view section “P ower Connection” on page 15 to verify that the ...

  • Patton electronic 2707/I - page 18

    18 T able 2: LED descriptions LED Description E1 Link (Active Green) Solid g reen (On) indicates that the end to end E1 Link is up , signifying that the link is active . The E1 Link LED is Off when the link is down. 10BT Link (Active Green) Solid green indicates that the 10Base-T Ethernet interface has detected a v alid SQE hear tbeat, signifying a ...

  • Patton electronic 2707/I - page 19

    19 6.3 OPERATING LINE LOOPBACK (LL) The Line Loopback (LL) test chec ks the operation of the local Model 2707/I, and is perf ormed separately on each unit. Figure 12. Line loopback f or a networ k ter mination application T o perform an LL test, set DIP s witch S1-2 to On . The TM LED will be lit while the unit is in loopback test mode . Model 2707 ...

  • Patton electronic 2707/I - page 20

    20 APPENDIX A G.703 SPECIFICATIONS A.1 NETWORK DATA RATE 2.048 Mbps A.2 NETWORK CONNECTOR RJ-48C/Dual Coax BNC A.3 NOMINAL IMPEDANCE 75/120 ohm A.4 LINE CODING Selectable AMI or HDB3 A.5 LINE FRAMING G.703 (Unframed) A.6 CLOCKING Internal or Networ k (Receive Reco ver) A.7 DISTANCE Maximum 6,000 ft (1.6 km) On 24 A WG cable ...

  • Patton electronic 2707/I - page 21

    21 APPENDIX B ETHERNET 10BASE-T SPECIFICATIONS B.1 DTE INTERFACE 10Base-T on RJ-45F B.2 DTE DATA RATES 10 Mbps B.3 LAN CONNECTION RJ-45, 10Base-T , 802.3 Ether net B.4 PROTOCOL PPP (RFC 1661) with Bridging Control (RFC 1638) B.5 MAC ADDR ESS T ABLE SIZE 4096 entries B.6 MAC ADDR ESS AGING MA C addresses deleted after 8 minutes of inactivity B.7 FRA ...

  • Patton electronic 2707/I - page 22

    22 B.12 POWER SUPPLY 5 VDC external power supply 100–240V AC , 50–60Hz, 0.4A B.13 HUMIDITY Up to 90% non-condensing B.14 T EMPERATURE 0–50°C (32–122°F) B.15 DIMENSIONS 3.5L x 2.1W x 0.78H in.(9.0L x 5.3W x 2.0H cm) ...

  • Patton electronic 2707/I - page 23

    23 APPENDIX C F ACTOR Y REPLACEMENT P AR TS AND ACCESSORIES P atton Model # Description 2707/C G.703 NTU with a V .35 interface 2707/D G.703 NTU with an X.21 interf ace 2707/I G.7034 NTU with 10Base-T ethernet interface 08055DCUI Universal Input P ower Supply 07M2707/I User Manual ...

  • Patton electronic 2707/I - page 24

    24 Cop yright © 2006 P atton Electronics Company All Rights Reser ved. ...

メーカー Patton electronic カテゴリー Switch

Patton electronic 2707/Iのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 2707/Iの取扱説明書
- Patton electronicの製品カード
- パンフレット
- またはPatton electronic 2707/Iの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Patton electronic 2707/Iの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Patton electronic 2707/Iの取り付け説明書、サービスマニュアル、簡易説明書、またはPatton electronic 2707/Iのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Patton electronic 2707/Iの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Patton electronic 2707/Iデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがPatton electronic 2707/Iを使用するのを助ける技術的文書のことです。説明書は通常、全てのPatton electronic 2707/Iユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Patton electronicの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Patton electronic 2707/Iの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははPatton electronic 2707/Iの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Patton electronic 2707/Iに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Patton electronic 2707/Iデバイスの基本機能を使うにあたってのヒント。 Patton electronic 2707/Iのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Patton electronic 2707/Iに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるPatton electronic 2707/Iのメーカー/サービスへの連絡先に関する情報。

Patton electronic 2707/Iについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもPatton electronic 2707/Iの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPatton electronic 2707/Iで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)