Graco HTX 257369の取扱説明書

28ページ 6.91 mb
ダウンロード

ページに移動 of 28

Summary
  • Graco HTX 257369 - page 1

    Repair HTX 2030 -For P ortable Airless and Air -Assisted Spra ying of Wat er-Based Arc hitectural Coatings with Base Coat Pump- -For Airless Spraying Arc hitec tural Coat ings and P aints with T op Coat Pump- Model Number: 257369 Maximum W orking Pressure: Base Coat Pump: 1000 psi (69 bar , 6.9 MP a) T op Coat Pump: 3300 psi (228 bar , 22.8 MP a) R ...

  • Graco HTX 257369 - page 2

    Contents 2 313889B Contents Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 W arning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Component I dentificati on - Spra yer . . . . . . . . . . . 5 Component I dentifica tion - Base Coat Applica tor 6 T roubleshooting . . . . . . . . . . . . . . . . ...

  • Graco HTX 257369 - page 3

    Warning 313889B 3 Wa r n i n g The f ollowing warnings are for the se tup, use , gro undi ng, maintenance, and repair of this equipment. The exc lamation point symbol alerts you to a general warning and t he hazard symbol refer s to procedure-sp e- cific risk. Ref er back to these warnings. Ad ditional, product-s pecific warnings may be f ound thro ...

  • Graco HTX 257369 - page 4

    Warning 4 313889B PRESSURIZED ALUMINUM P ARTS H AZARD Do not use 1,1,1-trichloroethane, met hylene chloride , other halogenated hydrocarbon solvents o r fluids containing such solv ents in pressurized alumin um equipment. Such use can cause serious chemical reaction and equipment rupture, and result in death, ser ious injury , and property damage. ...

  • Graco HTX 257369 - page 5

    Component Identification - Sprayer 313889B 5 Component Identification - Spra yer ti14415a 1 2 3 4 5 7 8 11 10 9 6 T op Coat Kit 8 12 1 ON/OFF Switch 2 Prime Switch (used with Base Coat Pump) 3 Pump Co ntrol 4 Hea vy T ext ure Material Hose (used with Base Coat Pump) 5 Applicator Switch (used with Base Coat Pump --on Hose 5) 6 Applica tor (Base Coat ...

  • Graco HTX 257369 - page 6

    Component Identification - Base Coat Applicator 6 313889B Component Identification - Base Coat Applicator ti14357a 1 2 3 4 5 6 9 10 7 8 1 Applicator 2 Air Hose Adap ter and Air Adjustment V alv e 3 Airless Filter or Air P assage Plug 4 Filter Supp or t 5 Airless Spray As sembly 6 Airless Spray Tip 7 Air nozzle , 4 mm, 6mm, 8mm, 10mm 8 Air Nozzle Cl ...

  • Graco HTX 257369 - page 7

    Troubleshooting 313889B 7 T r oubleshooting Prob lem Cause Solution E=XX is display ed F ault condition exists Deter mine f ault correction from Digital Display Mes- sages table , see manual 313888. Engine will not star t Engine switch is OFF T ur n engine switch ON Engine is out of gasoline Refill gas tank. Honda Engines Owner's Manual. Engin ...

  • Graco HTX 257369 - page 8

    Troubleshooting 8 313889B Pump output is low ( Base Coat Pump see pag es 22. To p C o a t P u m p see manual 310894) Strainer (82) is clogged Clean strainer . Piston ball is not seating Ser vice piston ball. Piston packings are worn or damaged Replace packings. O-ring in pump is wor n or damaged Replace o-ring. Intake v alve ball is not seating pro ...

  • Graco HTX 257369 - page 9

    Pressure Relief Procedure 313889B 9 Pressure Relief Pr ocedure Applicator (Base Coat Pump) 1. T ur n engi ne OFF . 2. T ur n on/off switch OFF and tu rn p ressure contr ol knob fully counterclockwise. 3. T urn prime/drain v alve do wn to DRAIN position. Fluid from dr ain valv e can splash in ey es or skin and cause serious injur y . K eep hands cle ...

  • Graco HTX 257369 - page 10

    Repair 10 313889B Repair Bearing Housing and Connecting Rod Re m ova l Relie ve Pressure , page 9. 1. Remov e Pump , page 22. Remove f our screws (45) an d front cover (44). 2. Remo ve f our scre ws (64) and washer s (63) from ProConnect bearing housing (40). 3. Pull connecting rod (43) and lightly tap low er rear of bearing housing with plastic ma ...

  • Graco HTX 257369 - page 11

    Repair 313889B 11 Installation 1. Ev enly lubricate inside of bronze bearing (C) in bearing housing (40) with high-quality mot or oil. Lib- erally pac k top roller bearing (E), low er bearing (D) inside connecting ro d (43) with bearing grease. 2. Assemb le connecting rod (43) to bearing housing (40). Rotate co nnecting rod to lowest position. 3. C ...

  • Graco HTX 257369 - page 12

    Repair 12 313889B Drive Housing Re m ova l Relie ve Pressure , page 9. 1. Remov e Bearing Housing , page 10. 2. Remov e six screws (38). 3. Lightly t a p around driv e housing (33) to loosen dr ive housing. Pull driv e housing straight off pinion hous- ing. Be pre pared to suppor t combination gear (32) which ma y also come out. Installation 1. App ...

  • Graco HTX 257369 - page 13

    Repair 313889B 13 Pinion Assembl y / Clutch Armature / Clamp Pinion Assembl y / Clutch Armature Re m ova l If pinion assemb ly (29) is not remov ed from clutch hou s- ing (19), perf orm steps 1 through 3. Othe rwise, star t at step 4. Pinion Assembl y 1. Remo ve drive hou sing, page 12. 2. Disconnect clutch cable connectors fr om inside of pressure ...

  • Graco HTX 257369 - page 14

    Repair 14 313889B Clutch Armature 8. Use an impact wrench or w e dge something between clutch armature (25) a nd clutch housing to hold engine shaft during remov al. 9. Remo ve f our scre ws (23) and lock w ashers (24). 10. Remove armatur e (25). Installation Clutch Armature 1. La y two stacks of two dime s (or 1.4mm c oins) on a smooth bench surf ...

  • Graco HTX 257369 - page 15

    Repair 313889B 15 Clamp Installation 1. Install engine shaft k ey (18). 2. T ap clamp (22) onto engine shaft (A). Maintain dimension of 2. 612 ± .010 in. (66.34 ± .25mm). Chamfer must f ace engine. 3. Check dimension: Plac e rigid , straight steel ba r (B) across face of clutch ho using (19). Us e accurate measuring de vice to measure distance be ...

  • Graco HTX 257369 - page 16

    Repair 16 313889B 9. Place pinion assembly on bench with ro tor side up. 10. Apply thread s ealant to scr ews . Install four screws (28) and lo ck w a shers (24). A lter nately to rque screws t o 125 ± 10 in-lb (14 ± 1.1 N•m) until rotor is secure. Use th readed holes to hold rotor . 11. Install pini on assembly (29) with f our screws (36) and ...

  • Graco HTX 257369 - page 17

    Repair 313889B 17 Clutch Housing Re m ova l 1. Remo ve f our scre ws (20) and lock w ashers (21) which hold clutch housin g (19) to engine. 2. Remove scre w (35) from under mount ing plate (D). 3. Pull off clutch ho using (19). Installation 1. Push on clutch hou sing (19). 2. Install f our capscre w s (20) and loc k washers (21) and secure clutch h ...

  • Graco HTX 257369 - page 18

    Repair 18 313889B Pressure Contr ol Pump On/Off Switch Re m ova l 1. Remov e two screws (71) and s wing down cov e r (70a). 2. Disconnect pu mp ON/OFF switch (70 j) connector from contro l board. 3. Press in on tw o retaining tabs on each side of pump ON/OFF switch (70j) and rem ov e switch from cov e r . Installation 1. Install ne w ON/OFF s witch ...

  • Graco HTX 257369 - page 19

    Repair 313889B 19 Contr ol Board Re m ova l 1. Remove two screws (71) and swing cover (70a) down. 2. Squeeze strain relief bush ings (70b) with pliers and remove . 3. Disconnect all leads at control board (70c). See Wiring Diagram , pag e 24. 4. Remo ve f our screws (7 0d) and control board (70c). Installation 1. Install cont rol board (70c) with f ...

  • Graco HTX 257369 - page 20

    Repair 20 313889B Pressure Contr ol T ransducer Re m ova l 1. Remove two screws (71) and swing cover (70a) down. 2. Disconnect t ransducer lead (158) fr om control board (70c). 3. Remov e strain r elief (70b) and pull tr ansducer cable from the control bo x. Remo ve scre ws (182) and cov er (184) to det ach transducer from car t frame. 4. Remove pr ...

  • Graco HTX 257369 - page 21

    Repair 313889B 21 Pump Contr ol Re m ova l 1. Remove two screws (71) and swing cover (70a) down. 2. Disconnect pu mp control (70p) lead from control board (70c). 3. Loosen set screws on pump co ntrol knob (7 0k) and remov e knob , sh aft nut, lock washer and pump con- trol (70p). 4. Remo ve shaft spacer (70n) from pump control. Installation 1. Inst ...

  • Graco HTX 257369 - page 22

    Repair 22 313889B Displacement Pump Re m ova l 1. Flush pump, p age 22. 2. Stop pump with piston rod in it s low est position. 3. P erform Pressure Relief procedure , page 9. 4. T op Coat Pump: Separate drain hose from spray er. 5. Disconnect t ransducer from pump manif old. 6. Raise latch loc k and push latch open. 7. Ratchet open pump door . a. R ...

  • Graco HTX 257369 - page 23

    Repair 313889B 23 Installation 1. Adjust piston rod t o proper length: Adjust piston rod with pin holder to pull ou t piston rod. T ap pis ton rod on hard surf ac e to push in piston rod. 2. Slide pump int o connecting rod. Pu sh pump collar flush with bearing housing ledge to be ab le to close pump door. 3. Push pump pin until it is fully retained ...

  • Graco HTX 257369 - page 24

    Wiring Diagram 24 313889B Wiring Diagram D12 LED J9 J5 J4 J3 J1 J2 J10 ti13556a N M K J F B A E H G C D A T o Engine B T o Ground C Clutch T est P oints D Pinion ED r i v e F On/Off Switch G Control Board H Pump Sensor J Pump/Prime Switch K Displa y Board M Pump Control N T ransducer ...

  • Graco HTX 257369 - page 25

    Technical Data 313889B 25 T echnical Data Dimensions Honda GX 200 Engine: ANSI P ower Rating @ 3600 rpm 6.5 Horsepower (4.8 kW) Maximum W orking Pressure: Base Coat Pump 1000 psi (69 bar , 6.9 MPa) T op Coat Pump 3300 psi (228 bar , 22.8 MPa) Noise Level: Sound P ower 105 dBa per ISO 3744 Sound Pressure 96 dBa measured at 3.1 ft (1 m) Maximum Deliv ...

  • Graco HTX 257369 - page 26

    Notes 26 313889B Notes ...

  • Graco HTX 257369 - page 27

    Notes 313889B 27 ...

  • Graco HTX 257369 - page 28

    Graco Standard Warra nty 28 313889B Graco Standar d W arranty Graco warrants all equipment ref erence d in this document which is manufactured b y Graco and bear ing its name to be free from de fe c t s i n material and workmanship on the date of sale to the origin al purch aser for use. With the e xception of any special, extended, or limited w ar ...

メーカー Graco カテゴリー Paint Sprayer

Graco HTX 257369のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- HTX 257369の取扱説明書
- Gracoの製品カード
- パンフレット
- またはGraco HTX 257369の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Graco HTX 257369の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Graco HTX 257369の取り付け説明書、サービスマニュアル、簡易説明書、またはGraco HTX 257369のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Graco HTX 257369の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Graco HTX 257369デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがGraco HTX 257369を使用するのを助ける技術的文書のことです。説明書は通常、全てのGraco HTX 257369ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Gracoの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Graco HTX 257369の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははGraco HTX 257369の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Graco HTX 257369に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Graco HTX 257369デバイスの基本機能を使うにあたってのヒント。 Graco HTX 257369のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Graco HTX 257369に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるGraco HTX 257369のメーカー/サービスへの連絡先に関する情報。

Graco HTX 257369についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもGraco HTX 257369の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがGraco HTX 257369で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)