Ryobi CS -- RY34420の取扱説明書

52ページ 6.58 mb
ダウンロード

ページに移動 of 52

Summary
  • Ryobi CS -- RY34420 - page 1

    OPERA TOR’S MANUAL MANUEL D’UTILISA TION MANUAL DEL OPERADOR 30 CC 4-CYCLE STRING TRIMMERS T AILLE-BORDURES À LIGNE 4 TEMPS DE 30 CC RECOR T ADORAS DE HILO DE CUA TRO TIEMPOS 30 CC CS — R Y34420 SS — R Y34440 C430 R Y34420 S430 R Y34440 Le taille-bordures à ligne a été conçue et fabriquée conformément à nos strictes normes de fiabil ...

  • Ryobi CS -- RY34420 - page 2

    ii A - Reel Easy string head (tête à ligne de coupe de Reel Easy , cabezal del hilo de Reel Easy) B - Drive shaft housing (tube de l’arbre moteur , alojamiento del eje de impulsión) C - Coupler (coupleur , acoplador) D - Front handle (poignée avant, mango delantero) E - Strap hanger (dispositif d’accrochage, colgador para la correa) F - Ign ...

  • Ryobi CS -- RY34420 - page 3

    iii Fig. 3 A - Hanger cap (capuchon de suspension, tapa de suspensión) B - Hole (trou, orificio) C - Secondary hole (trou secondaire, orificio secundario) D - Button (bouton, botón) Fig. 4 A - Front handle (poignée avant, mango delantero) B - Bolt (boulon, perno) C - W asher (rondelle, arandela) D - Wing nut (écrou papillon, tuerca de mariposa) ...

  • Ryobi CS -- RY34420 - page 4

    iv A - Ignition switch (commutateur d’allumage, interruptor de encendido) B - T rigger lock (verrouillage de gâchette, seguro del gatillo) C - Throttle trigger (gâchette d’accélérateur , gatillo del acelerador) Fig. 13 A - Ignition switch (commutateur d’allumage, interruptor de encendido) B - T rigger lock (verrouillage de gâchette, segu ...

  • Ryobi CS -- RY34420 - page 5

    v A - Idle speed screw (vis de ralenti, tornillo de ajuste de la velocidad en vacío) Fig. 21 A - Latch (loquet, pestillo) B - Air filter cover (couvercle du filtre à air , tapa del filtro de aire) C - Pull cover to open (tirer sur le couvercle pour l’ouvrir , tire de la tapa para abrirla) Fig. 22 A - Air filter cover (couvercle du filtre à air ...

  • Ryobi CS -- RY34420 - page 6

    2  Introduction ...................................................................................................................................................................... 2 Introduction / Intr oducción   General Safety Rules ....................................................................................................... ...

  • Ryobi CS -- RY34420 - page 7

    3 — English GENERAL SAFETY RULES WARNING: Read and understand all instructions. Failure to follow all instructions listed below may r esult in electric shock, fir e and/or serious personal injury . READ ALL INSTRUCTIONS  For safe operation, r ead and understand all instructions before using this product. Follow all safety instructions. Failure ...

  • Ryobi CS -- RY34420 - page 8

    4 — English SPECIFIC SAFETY RULES  Inspect before use. Replace damaged parts. Make sure fasteners are in place and secur e. Check for fuel leaks.  Replace string head if cracked, chipped, or damaged in any way . Be sure the string head or blade is properly installed and securely fastened. Failur e to do so can cause serious injury .  Mak ...

  • Ryobi CS -- RY34420 - page 9

    5 — English SYMBOLS SERVICE Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the product to your nearest AUTHORIZED SERVICE CENTER for r epair . When servic- ing, use only identical replacement parts. WARNING: T o avo id seri ou s per so nal inju ry , d ...

  • Ryobi CS -- RY34420 - page 10

    6 — English ASSEMBL Y UNP ACKING This product r equir es assembly .  Carefully r emove the product and any accessories from the box. Make sure that all items listed in the packing list are included.  Inspect the product carefully to make sure no breakage or damage occurred during shipping.  Do not discard the packing material until you h ...

  • Ryobi CS -- RY34420 - page 11

    7 — English NOTE: The open side of the handle should face the operator .  Place the bolt through the fr ont handle. NOTE: The hex bolt hea d fits inside the hex r ecess molded into one side of the handle.  Reinstall the washer and wing nut.  Tighten wing nut securely . A TT ACHING THE GRASS DEFLECTOR WARNING: The line cutting blade on th ...

  • Ryobi CS -- RY34420 - page 12

    8 — English OPERA TION Ethanol (ethyl or grain alcohol) 10% by volume. Y ou may use gasoline containing up to 10% ethanol by volume. Gasoline containing ethanol may be marketed under the name “Gasohol.” Do not use E85 fuel. MTBE (methyl tertiary butyl ether) 15% by volume. Y ou may use gasoline containing up to 15% MTBE by volume. Methanol (m ...

  • Ryobi CS -- RY34420 - page 13

    9 — English OPERA TION T o advance the cutting line manually:  Stop the engine and disconnect the spark plug wir e.  Push the knob in while pulling on line(s) to manually advance the line. NOTE: Pro Cut II line cannot be advanced. T o replace the line, r efer to Installing Line in Pr o Cut II String Head later in this manual. CUTTING TIP ...

  • Ryobi CS -- RY34420 - page 14

    10 — English MAINTENANCE NOTE: Only use the knob to tighten the bolt. The use of other tools may allow overtightening of the bolt, which could damage the string head.  If removed, replace the spring into the string head and push down to seat.  Reinstall the spool. For the C430, the spool should be placed so “This side out for curved ...

  • Ryobi CS -- RY34420 - page 15

    11 — English MAINTENANCE  Stop the engine and disconnect the spark plug wir e.  Gather two of the pre-cut lengths of trimmer line provided or cut two pieces of trimmer line, in 11 in. lengths.  Insert the lines into the slots located on the sides of the string head. Line should be pushed in until approximately 1 in. protrudes fr ...

  • Ryobi CS -- RY34420 - page 16

    12 — English MAINTENANCE ADJUSTING V AL VE-TO-ROCKER ARM CLEARANCE See Figures 25 - 27. Inspect the valve-to-r ocker arm clearance after every 25 hours of operation. This should be done in a clean, dust- free envir onment. NOTE: This procedure requires partial disassembly of the engine. If you are unsur e if you are qualified to perform this oper ...

  • Ryobi CS -- RY34420 - page 17

    13 — English IF THESE SOLUTIONS DO NOT SOL VE THE PROBLEM CONT ACT YOUR AUTHORIZED SERVICE DEALER. TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION Engine will not start No spark. No fuel. Engine is flooded. C l e a n o r r e p l ac e s p a r k pl u g . R e s e t spa rk p lug gap. Refer to S pa rk Pl ug Replacement ear lier i n this ma nual. Push ...

  • Ryobi CS -- RY34420 - page 18

    14 — English IF THESE SOLUTIONS DO NOT SOL VE THE PROBLEM CONT ACT YOUR AUTHORIZED SERVICE DEALER. TROUBLESHOOTING W ARRANTY EMISSIONS MAINTENANCE SCHEDULE AND WARRANTED P ARTS LIST Emissions Parts Inspect Before Clean Every Replace Every Replace Every Each Use 5 Hours 25 Hours or Y early 50 Hours or Y early AIR FIL TER ASSY INCLUDES: FIL TER ... ...

  • Ryobi CS -- RY34420 - page 19

    15 — English W ARRANTY LIMITED WARRANTY ST A TEMENT T echtr onic Industries North America, Inc., warrants to the original retail purchaser that this R YOBI ® brand outdoor product is free from defect in material and workmanship and agrees to repair or replace, at T echtr onic Industries North America, Inc.’ s, discretion, any defective product ...

  • Ryobi CS -- RY34420 - page 20

    16 — English W ARRANTY THE FOLLOWING CALIFORNIA AIR RESOURCES BOARD (CARB ) ST A TEME NT ONL Y APP LIES TO MODE L NUMBE RS REQUIRED TO MEET THE CARB REQUIREMENTS. The U.S. Environmental Protection Agency (EP A), the California Air Resources Boar d (CARB), and T echtronic Industries North America, Inc., are pleased to explain the Emissions Control ...

  • Ryobi CS -- RY34420 - page 21

    17 — English NOTES ...

  • Ryobi CS -- RY34420 - page 22

    3 — Français RÈGLES DE SÉCURITÉ GÉNÉRALES A VERTISSEMENT : Lire et veiller à bien comprendr e toutes les instructions. Le non respect des instructions ci-dessous peut entraîner un choc électrique, un incendie et / ou des blessures graves. LIRE TOUTES LES INSTRUCTIONS  P ou r t rav ai lle r e n tou te sé cu rit é, li re e t v ei lle ...

  • Ryobi CS -- RY34420 - page 23

    4 — Français RÈGLES DE SÉCURITÉ P AR TICULIÈRES   Inspecter l’outil avant chaque utilisation. Remplacer les pièces endommagées. S’assurer que toutes les pièces de boulonnerie sont en place et bien serrées. S’assurer de l’absence de fuites de carburant.  Si la tête de coupe est fendue, brisée ou endommagée de quelque f ...

  • Ryobi CS -- RY34420 - page 24

    5 — Français SYMBOLES DÉP ANNAGE Le dépannage exigeant des précautions extrêmes et la connaissance du système, il ne doit être confié qu’à un technicien de service qualifié. En ce qui concer ne les réparations, nous recommandons de confier le produit au CENTRE DE RÉP ARA TIONS AGRÉÉ le plus pr oche. Utiliser exclusivement des piè ...

  • Ryobi CS -- RY34420 - page 25

    6 — Français A VERTISSEMENT : Si des pièces manquent, ne pas utiliser ce produit avant qu’elles aient été installées. Ne pas prendr e cette précaution pourrait entraîner des blessures graves. INST ALLA TION DU BLOC-MOTEUR SUR L ’ACCESSOIRE V oir la figure 2. A VERTISSEMENT : Ne jam ai s inst al le r , re tr ai t ou ajus te r un acce ss ...

  • Ryobi CS -- RY34420 - page 26

    7 — Français de l’arbre d’accessoire. T ourner légèrement le capuchon dans un sens et l’autre pour enclencher le bouton.   Le trou secondair e de l’arb re d’acc essoir e peut éga lement être utilisé pour suspendr e l’accessoir e. INST ALLA TION DE LA POIGNÉE A V ANT V oir la figure 4.  Retirer les écrou à oreilles, r ...

  • Ryobi CS -- RY34420 - page 27

    8 — Français UTILISA TION antipollution, certaines régions des États-Unis et du Canada utilisent des carburants oxygénés pour réduire les émissions. Si du carburant oxygéné est utilisé, s’assur er qu’il est sans plomb et conforme aux exigences d’indice d’octane minimum. Avant d’utiliser du carburant oxygéné, essayer de conna ...

  • Ryobi CS -- RY34420 - page 28

    9 — Français UTILISA TION A V ANCE DE LA LIGNE DE COUPE (TÊTE À LIGNE DE COUPE DE REEL EASY) L ’avance de la ligne est obtenue en tapant la tête de coupe sur le gazon, le moteur tournant à plein régime.  Faire tourner le moteur à plein régime.  T aper la tête de coupe sur le sol pour fair e avance la ligne. La ligne avance chaque ...

  • Ryobi CS -- RY34420 - page 29

    10 — Français A VERTISSEMENT : Utiliser exclusivement des pièces d’origine pour les réparations. L ’usage de toute autr e pièce pourrait créer une situation dangereuse ou endommager l’outil. A VERTISSEMENT : T oujours porter des lunettes de sécurité munies d’écrans latéraux lors de l’utilisation d’outils. Si une opération d? ...

  • Ryobi CS -- RY34420 - page 30

    11 — Français ENTRETIEN modèle S430, la tour ner dans le sens horair e afin qu’elle soit solidement fixée.   Installer le fil tel que décrit à la prochaine section du présent manuel. INS T A LLA TI ON D U F IL DA NS LA TÊ TE DE COUPE PRO CUT II V oir la figure 20. Utiliser du fil monofilament dont le diamètr e mesure entre 2,4 mm ...

  • Ryobi CS -- RY34420 - page 31

    12 — Français ENTRETIEN  Retirer les vis de la partie inférieure du couvercle moteur . Retirer le logement inférieur et le mettr e de côté.  Retirer le bouchon-jauge du réservoir d’huile.  Pen che r le blo c moteu r sur le cô té afin de verse r le lub rif ian t usée dans un contenant approuvé, en la drainant par l’orifice d ...

  • Ryobi CS -- RY34420 - page 32

    13 — Français SI LES PRÉSENTES SOLUTIONS NE RÉSOL VENT P AS LE PROBLÈME, CONT ACTER LE CENTRE DE RÉP ARA TIONS AGRÉÉ. DÉP ANNAGE PROBLÈME CAUSE POSSIBLE SOLUTION Le moteur ne démarre pas Pas d’étincelle. Pas de carburant. Moteur noyé. N e t t o y e r o u r e m p l a c e r l a b o u g i e . Rég ler l’ éc ar tem ent de l’ éle c ...

  • Ryobi CS -- RY34420 - page 33

    14 — Français SI LES PRÉSENTES SOLUTIONS NE RÉSOL VENT P AS LE PROBLÈME, CONT ACTER LE CENTRE DE RÉP ARA TIONS AGRÉÉ. DÉP ANNAGE GARANTIE PROGRAMME D’ENTRETIEN DU SYSTÈME D’ÉMISSIONS ET LISTE DES PIÈCES GARANTIES FIL TRE À AIR INCLUT : ÉLÉMENT FIL TRANT ......................................................... X LUBRIFIANT DE MO ...

  • Ryobi CS -- RY34420 - page 34

    15 — Français GARANTIE ÉNONCÉ DE LA GARANTIE LIMITÉE T echtr onic Ind us tri es Nor th Ameri ca , Inc. , gar ant it à l’a che teu r original que ce produit R YOBI ® est exempt de tous vices de matériaux ou de fabrication et s’engage à répar er ou remplacer gratuitement, à son choix, tout produit s’avérant défectueux au cours des ...

  • Ryobi CS -- RY34420 - page 35

    16 — Français GARANTIE L ’ÉNONCÉ DE CALIFORNIA AIR RESOURCES BOARD (CARB) QUI SUIT , S’APPLIQUE SEULEMENT AUX NUMÉROS DE MODÈLES QUI DOIVENT SE CONFORMER AUX EXIGENCES DE CARB. L ’U.S. Environmental Protection Agency (EP A), le Califor nia Air Resources Board (CARB) et T echtronic Industries North America, Inc. se font un plaisir de vo ...

  • Ryobi CS -- RY34420 - page 36

    17 — Français NOTES ...

  • Ryobi CS -- RY34420 - page 37

    3 — Español REGLAS DE SEGURIDAD GENERALES ADVERTENCIA: Lea y comprenda todas las instrucciones. El incumplimiento de las instrucciones señaladas abajo puede causar descar gas eléctricas, incendios y lesiones corporales serias. LEA TODAS LAS INSTRUCCIONES  Para utilizar este pr oducto de una forma segura, lea y entienda todas las instruccion ...

  • Ryobi CS -- RY34420 - page 38

    4 — Español REGLAS DE SEGURIDAD ESPECÍFICAS  Inspeccione el producto cada vez antes usarlo. Reemplace toda pieza dañada. Asegúrese de que todos los tornillos y demás elementos de unión estén en lugar y bien firmes. Revise la herramienta para ver si tiene fugas de combustible.  Reemplace el cabezal del hilo si estuviese agrietado, ast ...

  • Ryobi CS -- RY34420 - page 39

    5 — Español SÍMBOLOS ADVERTENCIA: Para evitar lesiones corporales serias, no intente utilizar este producto sin haber leído y comprendido totalmente el manual del operador . Si no comprende los avisos de advertencia y las instrucciones del manual del operador , no utilice este producto. Llame al departamento de atención al consumidor de Ryobi ...

  • Ryobi CS -- RY34420 - page 40

    6 — Español ADVERTENCIA: Para evitar un arranque accidental que podría causar lesiones corporales graves, siempre desconecte el cable de la bujía del motor de la bujía misma al ensamblar las piezas. INST ALACIÓN DEL CABEZAL MOTOR EN EL ADIT AMENTO V ea la figura 2. ADVERTENCIA: Nunca una ni ajuste ningún aditamento, desmontar o mientras est ...

  • Ryobi CS -- RY34420 - page 41

    7 — Español  El orificio secundario del eje del aditamento puede emplearse también para colgar éste. MONT AJE DEL MANGO DELANTERO V ea la figura 4.  Retire la tuerca de mariposa, arandela y per no del clip de la mango delantero.  Instale el mango delantero sobre el lado superior del alojamiento del eje de impulsión en el ár ea que i ...

  • Ryobi CS -- RY34420 - page 42

    8 — Español FUNCIONAMIENTO Si va a usar un combustible oxigenado, asegúrese de que no tenga plomo y satisfag a los requis itos relac ionados con el octanaje nominal mínimo. Antes de usar un combustible oxigenado, trate de confirmar el contenido del combustible. En algunos estados o provincias se requier e mostrar información en las bombas. A ...

  • Ryobi CS -- RY34420 - page 43

    9 — Español FUNCIONAMIENTO  Golpee el perilla sobre el suelo para hacer avanzar el hilo. El hilo avanza cada vez que se golpea sobre el suelo el retén del carr ete. No mantenga el perilla sobr e el suelo. NOT A: La cuchilla de cortar el hilo montada en el deflector de pasto corta el hilo a la longitud correcta. NOT A: Si el hil o se gas ta h ...

  • Ryobi CS -- RY34420 - page 44

    10 — Español ADVERTENCIA: Al dar servicio a la unidad, sólo utilice piezas de repuesto idénticas. El empleo de piezas diferentes puede causar un peligro o dañar el pr oducto. ADVERTENCIA: Siempre use gafas de seguridad o anteojos protector es con pr otección lateral al usar herramientas. Si la operación genera mucho polvo, también póngase ...

  • Ryobi CS -- RY34420 - page 45

    11 — Español   Instale el hilo de la forma descrita en la siguiente sección de este manual. INST ALACIÓN DEL HILO EN EL CABEZAL DEL HILO PRO CUT II V ea la figura 20. Use hilo monofilar de entre 2,4 mm (0,095 pulg.) y 2,7 mm (0,105 pulg.) de diámetro. Use hilo de repuesto de la calidad para obtener el mejor desempeño.  Apague ...

  • Ryobi CS -- RY34420 - page 46

    12 — Español MANTENIMIENTO  Quite los tor nillos de la tapa superior del motor y déjela a un lado.  Retire los tornillos de la parte inferior de la tapa del mo- tor . Quite la parte inferior del alojamiento y déjela a un lado.  Retire la tapa de relleno de aceite/varilla medidora de aceite.  Incline el cabezal motor hacia el costad ...

  • Ryobi CS -- RY34420 - page 47

    13 — Español SI CON EST AS SOLUCIONES NO SE RESUEL VE EL PROBLEMA, COMUNÍQUESE CON EL CONCESIONARIO DE SERVICIO AUTORIZADO DE SU PREFERENCIA. SOLUCIÓN DE PROBLEMAS PROBLEMA CAUSA POSIBLE SOLUCIÓN El motor no arranca No hay chispa. No hay combustible. Está ahogado el motor . L i m p i e o r e e m p l a c e l a b u j í a , s e g ú n s e a n ...

  • Ryobi CS -- RY34420 - page 48

    14 — Español SI CON EST AS SOLUCIONES NO SE RESUEL VE EL PROBLEMA, COMUNÍQUESE CON EL CONCESIONARIO DE SERVICIO AUTORIZADO DE SU PREFERENCIA. SOLUCIÓN DE PROBLEMAS GARANTÍA PROGRAMA DE MANTENIMIENTO P ARA EL CONTROL DE EMISIONES Y LIST A DE PIEZAS GARANTIZADAS Piezas para el control Inspeccionar cada vez antes Limpiar cada 5 Reemplazar cada 2 ...

  • Ryobi CS -- RY34420 - page 49

    15 — Español GARANTÍA DECLARACIÓN DE LA GARANTÍA LIMIT ADA T echtr onic Industries North America, Inc. garantiza al co mpr ad or orig in al al men ud eo que es te pr od uct o de la mar ca R YOBI ® carece de defectos en los materiales y en la mano de obra, y acuerda r eparar o remplazar , a la sola discreción de T echtronic Industries North ...

  • Ryobi CS -- RY34420 - page 50

    16 — Español GARANTÍA LA SIGUIENTE DECLARACIÓN DE LA OFICINA DE RECURSOS A TMOSFÉRICOS DE CALIFORNIA (CARB) SE APLICA SÓLO A LOS MODELOS OBLIGADOS A CUMPLIR CON LOS REQUISITOS DE DICHO ORGANISMO. La Direc ción de Protec ción Ambient al (EP A) de EE.UU., la Oficina de Recursos Atmosférico s de Califor nia (CARB) y T echtronic Industries No ...

  • Ryobi CS -- RY34420 - page 51

    17 — Español NOT AS ...

  • Ryobi CS -- RY34420 - page 52

    987000-405 10-24-08 (REV :03) W ARNING: The engin e exha ust fro m this pr oduc t contains chemicals known to the State of California to cause cancer , birth defects, or other reproductive harm. CALIFORNIA PROPOSITION 65 TECHTRONIC INDUSTRIES NOR TH AMERICA, INC. 1428 Pearman Dairy Road, Anderson, SC 29625 USA 1-800-860-4050 • www .ryobitools.com ...

メーカー Ryobi カテゴリー Trimmer

Ryobi CS -- RY34420のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- CS -- RY34420の取扱説明書
- Ryobiの製品カード
- パンフレット
- またはRyobi CS -- RY34420の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Ryobi CS -- RY34420の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Ryobi CS -- RY34420の取り付け説明書、サービスマニュアル、簡易説明書、またはRyobi CS -- RY34420のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Ryobi CS -- RY34420の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Ryobi CS -- RY34420デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがRyobi CS -- RY34420を使用するのを助ける技術的文書のことです。説明書は通常、全てのRyobi CS -- RY34420ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Ryobiの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Ryobi CS -- RY34420の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははRyobi CS -- RY34420の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Ryobi CS -- RY34420に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Ryobi CS -- RY34420デバイスの基本機能を使うにあたってのヒント。 Ryobi CS -- RY34420のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Ryobi CS -- RY34420に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるRyobi CS -- RY34420のメーカー/サービスへの連絡先に関する情報。

Ryobi CS -- RY34420についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもRyobi CS -- RY34420の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがRyobi CS -- RY34420で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)