-
Hunter Fan 44150 - page 1
OwnerÕ s Manual SINCE 1 8 8 6 ® 44150 ...
-
Hunter Fan 44150 - page 2
Other Quality Pr oducts fr om Hunter Fans Humidifiers Air Purifiers ...
-
Hunter Fan 44150 - page 3
W e ar e pleased you have selected one of our broad line of home comfort pr oducts. Our pr oducts are manufactur ed to high quality standards and ar e designed for years of service. W e hope you will be satisfied and thank you for buying a Hunter pr oduct. T able Of Contents Installation Operation Featur es 6 Remove Old Thermostat 8 Labeling Wir es ...
-
Hunter Fan 44150 - page 4
Read This Befor e Installing Thermostat IMPOR T ANT 1 Read the entir e installation section of this Owner’ s Manual thor oughly befor e you begin to install or operate your Hunter Thermostat. • Remove the mylar label fr om the display window . INST ALLA TION 2 All installation is normally performed at your thermostat. PROGRAMMING 3 Y ou can pra ...
-
Hunter Fan 44150 - page 5
This thermostat is designed to optimize the use of your heating and cooling equipment. It does this by matching your comfort (the temperatur es in your home) to your schedule. An example: 6 a.m. – Y ou wake up. Pr ogram 1 has the heat set to 70° (21°C). 7:30 a.m. – Y ou leave for work. The second pr ogram tur ns the heat back to 62° (17°C) ...
-
Hunter Fan 44150 - page 6
LIGHT 6-7 Featur es Manual switch for tur ning on heating and cooling system. Display backlight for viewing in the dark. Manual switch for automatic or continuous fan operation. Battery door for easy access Soft touch pr ogramming buttons (see below) Display shows time, day , temperatur e, pr ogram number , hold, usage and low battery indicator . R ...
-
Hunter Fan 44150 - page 7
Changes the clock into 12 or 24 hour (military) mode. For entering minute of day . For r evising and changing weekday or weekend pr ograms T o r eset filter counter back to zer o. Retur ns display to curr ent time and temperatur e. Automatically pr ograms the thermostat for weekday and weekend pr ogram settings. For entering day of week. Pr ovides ...
-
Hunter Fan 44150 - page 8
This thermostat comes with two #8 slotted scr ews and two wall anchors for mounting. T o install your unit, you should have the following tools and materials. ■ Slotted scr ewdriver ■ Electric drill and 3/16" bit ■ Hammer ■ T wo 1.5 V (AA) Size Alkaline batteries CAUTION: Do not remove any wiring from existing thermostat before reading ...
-
Hunter Fan 44150 - page 9
TYPICAL HOME THERMOST A TS FIGURE 1 W all Mounting Plate Thermostat Cover W all Mounting Plate Thermostat Cover ...
-
Hunter Fan 44150 - page 10
■ Each wir e coming from the wall to the existing thermostat is connected to a terminal point on that thermostat. Each of these terminal points is usually marked with a code letter as shown in T able A on page 11. ■ The number of wir es in your system can be as few as two (for heat only systems), as many as eight, or any number in between. If y ...
-
Hunter Fan 44150 - page 11
Wir e Labeling RH G Y W RC RH RH RC RC G G Y Y W W and connect to thermostat T erminal shown then mark wir e with label shown If the code letter on your existing thermostat is RH, R, VR or 4 24 V olt G or F Fan RC, VC 24 V olt Cool Y , C or M (See Note) Air Conditioning W or H Heating RED BLUE GREEN YELLOW WHITE This table will help you match the l ...
-
Hunter Fan 44150 - page 12
12-13 Installation NOTE: If your thermostat has one wire marked R or RH (4-wire system), then leave the jumper wire between the RH and RC terminals. Otherwise, if you have separate RH and RC wires (5-wire system), then remove the jumper wire between the RH and RC terminals. NOTE: Do not connect a “Common” wire (sometimes labelled “C”) to an ...
-
Hunter Fan 44150 - page 13
Snap open the wallplate fr om your thermostat by pressing the r elease tab on the bottom of the thermostat. Position wallplate on wall and pull existing wir es through lar ge opening. Then level for appearance. Mark holes for plastic anchors pr ovided if existing holes do not line up with Hunter Thermostat holes. Drill holes with 3/16" bit and ...
-
Hunter Fan 44150 - page 14
The heating system selector and the F°/C° selector switches ar e located on the Printed Cir cuit Board. ■ Heating system selector The heating system selector is a switch on the Printed Cir cuit Board on the inside of the thermostat. The switch is at “HG” position. Leave it in this position if you have a gas fur nace or an oil burner . If yo ...
-
Hunter Fan 44150 - page 15
■ Be sur e to tighten the terminal screws secur ely , otherwise a loose wire could cause operational pr oblems with your system or thermostat. ■ Push excess wir e back into hole to prevent interfer ence with mounting of the thermostat cover . ■ Make sur e the Function Switch is set at OFF , and the F AN-AUTO Switch is in AUTO. ■ Insert the ...
-
Hunter Fan 44150 - page 16
Pr ogramming 1 Remove mylar label covering display window . 2 When the heating or cooling system is actually operating, “HEA T” or “COOL” will appear on the display . 3 If power is interrupted the batteries will keep all pr ograms. 4 If “LOW BA TT” indicator appears on the display r eplace the batteries. Setting the Time and Day of W ee ...
-
Hunter Fan 44150 - page 17
■ Pr ess and hold until current hour appears on display . ■ Note the AM/PM indicator . ■ Pr ess and hold until current minutes appear on display . ■ Pr ess until current day appears on display . ■ Retur ns to normal time and temperatur e. ■ If r etur n is not pr essed it will r eturn automatically in 10 seconds. HOUR MIN DA Y RETURN M T ...
-
Hunter Fan 44150 - page 18
Pr ogramming Studies conducted by the Department of Ener gy estimate that setting your thermostat back 10°F for two 8-hour periods during winter can r educe your fuel bill by as much as 30%. By setting your thermostat up 5° for two 8-hour periods during summer you can r educe your fuel bill up to 25%. Y our thermostat is capable of holding up to ...
-
Hunter Fan 44150 - page 19
NOTE: The thermostat program will NOT take effect immediately after programming of your thermostat but at the next programmed time/temperature change. The thermostat is pre-set to 68°F (20°C) for heat and 78°F (25°C) for air conditioning. So if you want a temperature other than 68°F or 78°F (20°C or 25°C) right away , use the temporar y man ...
-
Hunter Fan 44150 - page 20
Pr ogramming Befor e programming or changing the pr ogram, use this Personal Program Schedule to determine which times and temperatur e settings will best satisfy both your comfort and ener gy saving requir ements. Use a pencil so you can r evise your recor ds each time you change your temperatur e settings. Personal Pr ogram Schedule FOR WINTER FO ...
-
Hunter Fan 44150 - page 21
Y our thermostat can be pr ogrammed in two dif ferent ways. 1. Auto-pr ogram method 2. Manual method Befor e programming, position the Heat/Of f/Cool selector to the mode to be pr ogrammed. Auto-pr ogram method In auto-pr ogram method, you can program your thermostat instantly for the entir e week by simply pr essing “Auto Prog.” key once. When ...
-
Hunter Fan 44150 - page 22
Pr ogramming W eekday Pr ograms Step 1 Step 2 ■ Normal display of time, temper - atur e, and day of the week. ■ Pr ogram indicator (1) is displayed. ■ 68°F is displayed. ■ 0:00 space for time is displayed. ■ M to F is displayed. PROG M T W TH F SA SU SET TEMP HOLD TEMP 8 9 : 15 72 c AM PM HEAT COOL 1234 FILTER LO BAT M T W TH F SA SU SET ...
-
Hunter Fan 44150 - page 23
Step 3 Continue for W eekend Pr ograms ■ Pr ess on once to change temperatur e to 69°F . ■ W eekday program 1 is complete. ■ Pr ess PROG to move to program 2, 3, and 4 and follow the same steps Pr ess to move to weekend pr ograms. W eekends can be pr ogrammed with one schedule, or dif ferent schedules for Satur day and Sunday . M T W TH F SA ...
-
Hunter Fan 44150 - page 24
Pr ogramming W eekday Pr ogram ■ Normal display of curr ent time, temperatur e, and day of week. ■ 1st weekday pr ogram is displayed. ■ Pr ogram indicator (1) appears. ■ M to F indication appears. PROG PROG M T W TH F SA SU SET TEMP HOLD TEMP 8 9 : 15 72 c AM PM HEAT COOL 1234 FILTER LO BAT M T W TH F SA SU SET TEMP HOLD TEMP 8 6 : 00 68 c ...
-
Hunter Fan 44150 - page 25
T o Review The Curr ent T emperatur e Setting: Pr ess for 2 seconds or less: or ■ Curr ent time and temperature M T W TH F SA SU SET TEMP HOLD TEMP 8 9 : 15 68 c AM PM HEAT COOL 1 2 34 FILTER LO BAT ■ 70 indicates the curr ent setting of the thermostat is 70°F . 68 shows the pr esent room temperatur e as 68°F . ■ If held for mor e than 2 se ...
-
Hunter Fan 44150 - page 26
Pr ogramming ■ Pr ess arrow to display curr ent set and r oom temperatures. M T W TH F SA SU 89 : 68 60 c AM PM HEAT COOL 1 2 34 FILTER LO BAT M T W TH F SA SU SET TEMP HOLD TEMP 89 : 70 60 c AM PM HEAT COOL 1234 FILTER LO BAT T emporary Manual Override In the following example, the pr esent room temperatur e is 60°F and we want to raise the tem ...
-
Hunter Fan 44150 - page 27
In the event you wish to hold your manual override for vacation or just an extended period of time, follow the temporary manual override instructions on page 26, then immediately pr ess HOLD/CLEAR. This will maintain override setting indefinitely . “HOLD” will appear on the display . ■ T o r etur n immediately to the curr ent program, pr ess ...
-
Hunter Fan 44150 - page 28
Operations 72 . 7I . 70 . Filter Monitor T o Reset the Filter Counter to Zer o ■ Filter indicator disappears. M T W TH F SA SU SET TEMP HOLD TEMP 8 6 : 30 6 8 c AM PM HEAT COOL 1 234 FILTER LO BAT M T W TH F SA SU SET TEMP HOLD TEMP 8 6 : 30 6 8 c AM PM HEAT COOL 1 234 FILTER LO BAT FIL TER RESET 28-29 The Hunter Digital Thermostat measur es and ...
-
Hunter Fan 44150 - page 29
Other Featur es Y our thermostat is pr e-programmed at the factory to cycle when the temperatur e rises 1° above or 1° below the temperature setting to pr ovide maximum comfort. It cannot be changed. T emperatur e Span Pr ess Y our thermostat comes with an electr olumi- nescent lamp for easy viewing of the display in the dark. T o activate pr ess ...
-
Hunter Fan 44150 - page 30
T r oubleshooting Pr oblem Solution SCRAMBLED OR DOUBLE DISPLA Y (numbers over numbers) NO DISPLA Y ENTIRE DISPLA Y DIMS PROGRAM DOES NOT CHANGE A T YOUR DESIRED SETTING AUTO/F AN DOES NOT COME ON 1. Remove clear mylar sticker . 1. Check battery connections and batteries. 2. Pr ess reset button once with a small pin and hold in for two seconds. 1. ...
-
Hunter Fan 44150 - page 31
Pr oblem (Continued) Solution (Continued) HEA TING OR COOLING DOES NOT GO ON OR OFF ERRA TIC DISPLA Y IF UNIT CONTINUES TO OPERA TE IN OFF POSITION THERMOST A T READS , HI, LO PERMANENTL Y 1. Check that function switch is in corr ect position (“HEA T” or “COOL”). 2. Ther e may be as much as 20 seconds delay in the thermostat tur ning the sy ...
-
Hunter Fan 44150 - page 32
Wiring Diagrams 32 4-wir e Heat/Cool System 5-wir e Heat/Cool System THERMOST A T G W Y RH RC Heat Relay or V alve Heat /Cool T ransformer Fan Relay Cool Contactor Jumper THERMOST A T G W Y RH RC Heat Relay or V alve Heat T ransformer Fan Relay Cool Contactor Cool T ransformer ...
-
Hunter Fan 44150 - page 33
2-wir e Heat Only 3-wir e Cool Only 3-wir e Heat Only THERMOST A T G W Y RH RC Heat Relay or V alve Heat T ransformer THERMOST A T G W Y RH RC Heat Relay or V alve Heat T ransformer Fan Relay THERMOST A T G W Y RH RC Cool Contactor Fan Relay Cool T ransformer ...
Hunter Fan 44150についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもHunter Fan 44150の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHunter Fan 44150で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。