ページに移動 of 86
CH A P T E R 19-1 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 19 DLPs D200 to D299 DLP-D201 Apply a Lock-On Note T o apply a lock -on to a protect card in a 1:1 or 1:N protection grou p, the protect card must b e acti ve. If the prote ct card is in standby , th e Lock On button is disa bled. T o make the protect card acti ve, you must sw ...
19-2 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D202 Apply a Lockout The Lock On stat e has been applied and t raf f ic cann ot be switch ed to the w orking car d. T o clear t he Lock On state, see the “DLP-D203 Clear a Lock-O n or Lockout” task on page 19-3 . Step 8 Return to your ori ginating proc ...
19-3 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D203 Clear a Lock-On or Lo ckout DLP-D203 Clear a Lock-On or Lockout Step 1 In node vie w , click the Maintenance > Protection tabs. Step 2 In the Protection Groups list , click the protectio n group that contains the card you w ant to clear . Step 3 In ...
19-4 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D205 Clean Fiber Conne ctors with CLETOP Step 3 Blo w-dry using filtered air . Step 4 Use an inspection microscope to inspect each fiber connector for dirt, cracks, or scratches. If the connector is not clean, repeat Steps 1 to 3 . Step 5 Insert the f ib e ...
19-5 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D206 Clean the Fiber Adapters DLP-D206 Clean the Fiber Adapters Step 1 Remov e the dust plu g from the f iber adapter . Step 2 Insert a CLET OP stick swab (1410 0400) into the adapter op ening and rotate the swab . Step 3 Place dust plugs on th e fib er ad ...
19-6 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D208 Change External Al arms Using the AIC-I Card DLP-D208 Change External Alarms Using the AIC-I Card Step 1 Confir m that e xternal-de vice relay s are wired to the ENVIR ALARMS IN p ins on the MIC-A/P Front Mount Electrical Connection (FMEC). See the ? ...
19-7 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D210 Change AIC-I Card Orderwire Settings Step 3 On the External Controls subtab, modify any of t he follo wing f ields for each external contro l wired to the ONS 1545 4 SDH MIC-A/P card. For definitions of these fields, see the “NTP-D247 Pro vision Ext ...
19-8 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D211 Provision CE- 1000-4 Ethernet Ports DLP-D211 Provision CE-1000-4 Ethernet Ports Note Y ou can provision SONET contiguous concatenated (CCA T) or virtual concatenat ed ( VCA T) circuits for the CE-1000-4 before or after pro visioning the card’ s Ethe ...
19-9 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D212 Create a User Data Channel Circuit Note Reprovision ing an Ethernet port on the CE-1000- 4 card does not reset the Ethernet statistics for that port. Step 6 Return to your ori ginating procedure (NTP). DLP-D212 Create a User Data Channel Circuit Step ...
19-10 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D213 Provision th e Card Mode for ML-Series Ethernet Cards DLP-D213 Provision the Card Mode for ML-Series Ethernet Cards Step 1 In node vie w , double-click the ML-Series Ethernet card graphic to open the card. Step 2 Click the Pro visioning > Card tab ...
19-11 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D215 Consolidate Links in Network View Step 2 Click the Pro visioning > Line tabs for all cards except the G-Series card. For the G-Series card, click the Provisio ning > Port tabs. Step 3 In the Admin State column for the tar get port, choose on e ...
19-12 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D215 Consolidate Links in Ne twork View Step 1 From the V iew men u, choose Go to Network V i ew . CTC shows the link icons by default. Step 2 As needed, perfo rm one or more o f the follo wing steps: • T o toggle link icons on and of f, go to Step 3 . ...
19-13 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D215 Consolidate Links in Network View Figur e 19-2 Consolidated Links in Networ k View Figure 19-3 sh o ws a dif feren t network vie w with local DCC link consolidation between t wo nodes. Figur e 19-3 Networ k View with Local Link Consolidation Step 6 T ...
19-14 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D216 Change the STM-N Card ALS Maintenance Settings b. Check the check box es ne xt to the links t hat you want to display . c. Click OK . Step 10 Return to your ori ginating procedure (NTP). DLP-D216 Change the STM-N Card ALS Maintenance Settings Note Fo ...
19-15 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D216 Change the STM-N Card ALS Maintenance Settings Step 4 Click Apply . If the change affects traf f ic, a warning message displays. Click Ye s to complete the change. Step 5 Return to your ori ginating procedure (NTP). T able 1 9-2 STM-N Maint enance Se ...
19-16 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D217 MS-SPRing Exercise Ring Test DLP-D217 MS-SPRing Exercise Ring Test Step 1 From the V iew men u, choose Go to Network V i ew . Step 2 Click the Pro visioning > MS-SPRing tabs. Step 3 Click the ro w of the MS-SPRing you will e x ercise, then click E ...
19-17 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D217 MS-SPRing Exercise Ring T est Step 5 Exercise the east port: a. Right-click the east port o f any MS-SPRing node and choose Set East Pr otection Opera tion . Note For tw o fiber MS- SPRings, the squares on the node icons represen t the MS-SPRing work ...
19-18 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D218 Provision SNCP Ring Se lectors During Circuit Creation DLP-D218 Provision SNCP Ring Selectors During Circuit Creation Note Provisioning SD-P or SF-P thresholds on the Circuit Attrib utes page of the Circuit Creation wizard sets the values only for SN ...
19-19 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D219 Provision a Low-Order Tunnel Route DLP-D219 Provision a Low-Order Tunnel Route Step 1 In the Circuit Creation wizard i n th e Route Revie w and Edit area, click the source node icon if it is not already selected. Arrows indicate the a vailable sp ans ...
19-20 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D221 Provision E-Series Ethe rnet Ports for VLA N Membership Note Both 1000 Full and Au to modes set the E1000-2- G port to the 1000 Mbps and Full duple x operating mode; ho wever , flow con trol is disabled when 1000 Full is selected. Choosi ng Auto mode ...
19-21 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D221 Provision E-Series Ether net Ports for VLAN Membership • If a port is a member of only one VLAN, cho ose Untag from the Port column in the VLAN’ s row . Choose -- for all the other VLAN ro ws in that Port col umn. Note The VLAN with Untag selecte ...
19-22 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D222 Provision G-Series Ethern et Ports DLP-D222 Provision G-Series Ethernet Ports Step 1 In node vie w , double-click the G-Series card graphic to open the card. Step 2 Click the Pro visioning > Por t tabs. Step 3 For each G-Seri es port, pro vision t ...
19-23 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D223 Download an Alarm Severity Profile Note Reprovision ing an Ethernet po rt on the G-Series card does n ot reset the Ethernet statistics for that port. Step 6 Return to your ori ginating procedure (NTP). DLP-D223 Download an Alarm Severity Profile Step ...
19-24 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D224 Adjust the Java Virtual Memory Heap Size Note The Default alarm profile list contains alarm and condition se v erities that correspond when applicable to default valu es esta blished in T elcordia GR-253-CORE. Note All default or user -def ined se v ...
19-25 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D225 Enable Alarm Filtering Step 7 Ty p e 512 in the V ariable V alue field. Step 8 Click OK . Step 9 Reboot your PC. Step 10 Return to your ori ginating procedure (NTP). DLP-D225 Enable Alarm Filtering Step 1 At node, network, or car d vie w , click the ...
19-26 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D227 Disable Alarm Filtering DLP-D227 Disable Alarm Filtering Step 1 At node, network, or car d vie w , click the Alarms tab . Step 2 Click the Filter tool at the lo wer -ri ght side of the bottom to olbar . Alarm filt ering is enabled if the t ool is ind ...
19-27 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D230 Change a Circuit State In the Circuits on Span dialog bo x, you can vie w the follo wing in formation about the cir cuits that tra verse th e span. The information t hat appears depends on the circuit type. F or lo w-order and high-or der circuits pr ...
19-28 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D231 Edit a Circuit Name Step 5 In the Set Circuit State di alog box, choose the administrati v e state fr om the T arget Circuit Admin State drop-do wn list: • Unlocked—Puts the circuit cr oss-connects in the Unlock ed-enabled service state. • Lock ...
19-29 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D232 Change Active and Standby Spa n Color Step 2 Click the circuit you wa nt to rename, then cli ck Edit . Step 3 If you want to edit a VCA T circuit member name, complete the fol lo wing steps in the Edit Circuit window to access the Edit Member wind o ...
19-30 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D233 Edit SNCP Circuit Path Selectors c. Click OK to close the Pick a Color dialog box. If you wa nt to change th e standb y span color , continue with Step 5 . If not, click OK to s av e th e change an d close the Pref erences dialog box , or click Apply ...
19-31 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D234 Roll the Source or De stination of One Optical Circuit • (VC4 circuits onl y) In the VC LO Circuit s Only area, set the follo wing t hresholds: – SF threshold—Sets the SNCP si gnal failure BER threshold. – SD threshold— Sets the SNCP si gna ...
19-32 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D234 Roll the Source or Destination of One Op tical Circuit Figur e 1 9-5 Selecting Single Roll At tr ibut es Step 6 Click Next . Step 7 In the Pi vot/ Fixed Poi nt 1 windo w , click the square in the graphic image that repr esents the facility that you w ...
19-33 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D234 Roll the Source or De stination of One Optical Circuit Figur e 1 9-7 Selecting a New Endpoint Step 10 Click Finish . On the Circuits tab, t he circuit status for the Roll Fro m port changes from DISCO VERED to R O LL_PENDING. Step 11 Click the Rolls ...
19-34 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D235 Roll One Cross-Connec t from an Optical Circuit to a Second Optical Circuit Figur e 19-8 Viewing the Rolls T ab Step 12 If you selected Manual in Step 5 , click the rolled f acility on the Roll s tab and then click Complete . If you selected Auto, co ...
19-35 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D235 Roll One Cross-Connect from an Op tical Circuit to a Second Optical Circuit b. From the Circuit Roll T y pe drop-do wn list, choose Single to indicate that yo u want t o roll a single connection from the Roll Fro m circuit to the Roll T o circuit. c. ...
19-36 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D236 Roll Two Cross-Conn ects on One Optic al Circuit Using Automatic Ro uting • A roll can be forced onto th e Roll T o Circuit destination without a v a lid signal by using t he Force V alid Signal button. If you choose Force V alid Signal, traff ic o ...
19-37 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D236 Roll Two Cross-Connects on One Optical Circuit Using Automatic Routing Figur e 1 9-1 0 Selecting Dual Roll At tr ibutes Step 6 Click Next . Step 7 In the Pi v ot/Fix ed Point 1 w indo w , click the square re presenting the f ix ed path of the first c ...
19-38 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D236 Roll Two Cross-Conn ects on One Optic al Circuit Using Automatic Ro uting Figure 1 9-1 1 Setting Roll Routing Pr efer enc es Step 13 T o route the circuit ov er a protected path, check Fully Protected Path . (If you do not w ant to route th e circuit ...
19-39 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D236 Roll Two Cross-Connects on One Optical Circuit Using Automatic Routing Step 16 If you check ed Re vie w Route Before Creation in Step 12 : a. In the Roll Route Re vie w an d Edit area, re vie w the circuit rout e. T o add or delete a circuit span, se ...
19-40 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D237 Roll Two Cross-Conn ects on One Optic al Circuit Using Manual Routing DLP-D237 Roll Two Cross-Connects on O ne Optical Circuit Using Manual Routing Step 1 From the V iew men u, choose Go T o Network V iew . Step 2 Click the Circui ts tab . Step 3 Cli ...
19-41 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D237 Roll Two Cross-Connects on One Optical Circuit Using Manual Routing Step 13 Set the circuit path protect ion: • T o route the circuit on a protected path, leav e Fully Protected Path check ed and continue with Step 14 . • T o create an unprotecte ...
19-42 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D238 Roll Two Cross- Connects from One O ptical Circuit to a Secon d Optical Cir cuit Note Y ou cannot complete a ro ll if you cancel led the sibling roll. Y ou must complete the two rolls together . Step 20 For both manual an d automatic rolls, click Fin ...
19-43 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D238 Roll Two Cross-Connects from One Op tical Circuit to a Second Optical Circuit Step 9 Complete one of the follo wing : • If multiple Roll Fro m paths exist, th e Select Roll From dialog box appears. Select t he path from which you want to rol l traf ...
19-44 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D239 Delete a Roll DLP-D239 Delete a Roll Step 1 From the V iew men u, choose Go T o Network V iew . Step 2 Click the Circ uits > Rolls tabs. Step 3 Click the rolled circuit that you w ant to delete. Step 4 From the T ools menu, ch oose Circuits > D ...
19-45 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D241 Clear an MS-SPRing Manual Ring Switch Step 1 From node or netw ork vie w , click the Cir cuits > Rolls tabs. Step 2 Click the rolled circuit that you w ant to cancel. Step 3 Click Cancel . Step 4 Return to your ori ginating procedure (NTP). DLP-D2 ...
19-46 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D242 Create an MS -SPRing on a Single Node DLP-D242 Create an MS-SPRing on a Single Node Step 1 In node vie w , click the Pr ovisioning > MS -SPRing tabs. Step 2 In the Suggestion dialog box, cli ck OK . Step 3 In the Create MS-SPRing dialog box, enter ...
19-47 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D243 Create a VLAN DLP-D243 Create a VLAN Step 1 From the V iew men u, choose Go to Network V i ew . Step 2 From the T ools menu, ch oose Manage VLANS . Step 3 In the All VLANs dialog box, click Cr eate . Step 4 In the Def ine Ne w VLAN dialog box , compl ...
19-48 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D244 Use the Reinitialization Tool to Clea r the Database and Up load Software (Windows) DLP-D244 Use the Reinitialization Tool to Clear the Database and Upload Software (Windows) Caution Restoring a node to the f actory conf ig uration deletes all cross- ...
19-49 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D244 Use the Re initializa tion Tool to Clear the Database an d Upload Software (Windows) • User ID—Enter the user ID needed to access the node. • Password—Enter the password for the user ID. • Upload Package—Check this box to send the softwar ...
19-50 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D245 Use the Reinitialization Tool to Cl ear the Database and Upload Software (UNIX) DLP-D245 Use the Reinitialization Tool to Clear the Database and Upload Software (UNIX) Step 1 Insert the system so ftware CD containi ng the reinit tool, softw are, and ...
19-51 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D246 Provision E-Series Ethernet Card Mode Step 5 Click Go . Caution Before continuing with t he next st ep, verify t hat the database to upload is corr ect. Y ou cannot rev erse the upload process after you click Y es. Step 6 Re vie w the information on ...
19-52 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D247 Change an STM- N Card Step 6 Repeat Steps 1 through 5 for other nodes, as ne cessary . Step 7 Return to your ori ginating procedure (NTP). DLP-D247 Change an STM-N Card Caution Physically removing an STM-N card can cause a lo ss of working traf fi c ...
19-53 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D248 Delete VLANs Step 5 Complete the “NTP-D16 Install STM-N Card s and Connectors” procedure on page 2-7 . Step 6 Return to your ori ginating procedure (NTP). DLP-D248 Delete VLANs Note VLANs in use will not be deleted. Step 1 From the V iew men u, c ...
19-54 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D249 Provision IP Settings Step 2 Click the Pro visioning > Network > General tabs. Step 3 Complete the follo wing informati on in the f ields listed: • IP Address—T ype the IP address assigned to the ONS 154 54 SDH node. Note If TCC2P cards are ...
19-55 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D249 Provision IP Settings • Net/Subnet Mask Length—T ype the subnet mask length (decimal number representin g the subnet mask length in bits) or click the arro ws to adjust th e subnet mask length. Th e subnet mask leng th is the same for all ONS 154 ...
19-56 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D249 Provision IP Settings Step 6 Click OK . The network vie w appears. The node icon appears in gray , during which time you cannot access the node. Step 7 Double-click the node icon when it b ecomes green. As necessary , complete the “DLP-D65 Create a ...
19-57 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D250 Set Up or Change Open Shortest Path First Protocol DLP-D250 Set Up or Change Open Shortest Path First Protocol Step 1 In node vie w , click the Pr ovisioning > Netw ork > OSPF tabs. Step 2 On the top left side of the OSPF tab, complete the foll ...
19-58 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D250 Set Up or Change Open Shortest Path First Protocol Step 5 Provision the OSPF pr iority and interv al settings: The OSPF priority and interv al defaults are ones most commonly used b y OSPF routers. V erify that these defaults match the ones used by t ...
19-59 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D251 Set Up or Change Routing Information Protocol • Retransmit Int (sec)—Sets the time th at will elapse before a packet is resent. Fi ve seconds is the default. • Dead Int (sec)—Sets the number of seconds that will pass while an O SPF router’ ...
19-60 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D254 TCC2/TCC2P Card Active/Standby Switch Test Step 6 If you want to complete an address summary , comp lete the following steps. If not, con tinue with Step 7 . Complete the address summary only i f the ONS 15454 SDH is a ga te way NE with multi ple ex ...
19-61 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D255 Cross-Connect Card Side Switch Test Step 9 After the node ic on turns gree n (within 1 to 2 minutes), dou ble-click it. On t he shelf graphi c, observe the following: • The pre vious standby TCC2/TCC2P card has a green A CT LED. • The pre vious a ...
19-62 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D256 View Ethernet Statistics PM Parameters Step 5 Click the Maintenance > Cross-Connect tabs. Step 6 In the Cross-Connect Cards area, make a note of the activ e and standb y slots. Step 7 On the shelf graphic, verify that the acti ve cross-connect car ...
19-63 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D257 View Ethernet Utilizatio n PM Parameters Step 3 Click the Statistics subtab . Step 4 Click Refresh . Performance monitoring statistics appear for each port on the card. Step 5 V iew the PM parameter n ames in the P aram column. The current PM paramet ...
19-64 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D258 View Ethernet History PM Parameters DLP-D258 View Ethernet History PM Parameters Step 1 In node vie w , double-click the E-Se ries or G-Series Ethernet card where you w ant to vie w PM counts. The card vie w appears. Step 2 Click the Perf ormance tab ...
19-65 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D260 Set Auto-Refresh In terval for Displayed PM Counts • 15 min : This option displays the specif ied PM counts in fi fteen-minute time interv als. • 1 hour : This optio n displays th e specified PM coun ts in one- hour time i ntervals. • 1 day : T ...
19-66 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D261 Refresh PM Counts for a Different Port DLP-D261 Refresh PM Counts for a Different Port Step 1 In node vie w , double-cl ick the STM-N card where you w ant to vie w PM counts. The card vi e w appears. Step 2 Click the Perf ormance tab . Step 3 In the ...
19-67 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D262 Filter the Display of Circuits • Direction—Choose one to f ilter circui ts based on direction: An y (direction not used t o filt er circuits), 1-way (display only o ne-way circuits), or 2-way (display only two-way circuits). • OCHNC Di r—(DWD ...
19-68 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D263 Edit S NCP Dual-Ring Inte rconnect Circuit Hold-Off Timer Step 5 Click OK . Circuits match ing the attrib utes in th e Filter Circuit s dialog box appear in th e Circuits wi n d ow . Step 6 T o turn filtering off, click the Filter ic on in the lower ...
19-69 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D264 Provision a J1 Path Trace o n Circuit Source and Destination Ports DLP-D264 Provision a J1 Path Trace on Circuit Source and Destination Ports Note This task assumes that you are setting up path trace on a bidirectional circuit and sett ing up transmi ...
19-70 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D264 Provision a J1 Path T race on Circuit Source and Destination Ports Note If neither port is on a transmi t/recei ve card , you will not be ab le to complete this p rocedure. If one port is on a transmit/recei ve card and the ot her is on a recei ve -o ...
19-71 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D264 Provision a J1 Path Trace o n Circuit Source and Destination Ports d. (Check box visibility depends o n card selection) Click the Disable AIS on C2 Mis-Match check box if you w ant to suppress the A IS when a C2 mismatch occurs. e. Click Appl y , the ...
19-72 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D265 Change the Login Legal Disclaimer When you di splay the de tailed circuit window , path trace is indicated b y an M ( manual path trace) or an A (automatic path trace) at the circuit source and destination p orts. Step 13 Return to your ori ginating ...
19-73 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D266 Change IP Settings Step 4 Click Apply . Step 5 Return to your ori ginating procedure (NTP). DLP-D266 Change IP Settings Caution Changing the node IP address, subnet mask, or II OP listener port causes the TCC2/TCC2P cards to reboot. If Ethernet circu ...
19-74 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D268 Apply a Custom Networ k View Backgr ound Map If you changed a netw ork f ield that will cause the no de to reboot, the Change Netw ork Conf iguration confi rmation dialog box appears. If you changed a g ate way setting, a con fir mation appropriate t ...
19-75 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D269 Enable Dialog Bo x Do-Not-Display Option DLP-D269 Enable Dialog Box Do-Not-Display Option Note If any user who has righ ts to perfor m an operation (f or example, creating a circuit) selects the “Do not sho w this dialog again” check box on a dia ...
19-76 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D271 Change Node Se curity Policy on a Single Node Step 2 If you want to modify th e idle user timeout period, click t he hour (H) and minut e (M) arro ws in the Idl e User T imeout area for the securit y lev el you w ant to pro vision: RETRIEVE, MAINTEN ...
19-77 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D272 Change Node Security Poli cy on Multiple Nodes DLP-D272 Change Node Security Policy on Multiple Nodes Step 1 From the V iew men u, choose Go to Network V i ew . Step 2 Click the Provisioning > Security > Policy tabs. A r ead-only table of nod e ...
19-78 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D273 Modify SNMP Trap De stination • Disable Inacti v e User—If check ed, disables users wh o do not log into the nod e for the period of time specified i n the Inacti v e Duration box. The Inact i ve Dur ation range is 45 to 90 days. Step 9 In the Se ...
19-79 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D293 Perform a Manual Span Upgrade on a Two-Fiber MS-SPRing Step 9 SNMP settings are no w co nf igured. T o view SNMP information f or each node, highligh t the node IP address in the T rap Destinations area of the SNMP windo w . Confirm that the chang es ...
19-80 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D294 Perfor m a Manual Span Upgr ade on a Four-Fi ber MS-SPRing Step 10 When cards in both endpoi nt nodes ha v e been successfully upgraded and all the f acility alarms (LOS, SD, or SF) are cleared, remove the F orce switch fro m both end points on the u ...
19-81 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D295 Perform a M anual Span Upgrade on an SNCP Step 8 V erify that the transmit signal f alls wit hin the acceptabl e range. See T able 2-4 on page 2-17 for STM-N card transmit and recei v e le v els. Step 9 Complete the “DLP-D338 Instal l Fiber -Optic ...
19-82 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D296 Perfor m a Manual Span Up grade on a 1+1 Protec tion Group Step 10 Complete the “DLP-D198 Clear an SNCP Force Switch” task on page 18-85 when cards in bo th endpoin t nodes hav e been successfully upgraded and all th e facility alarms (LOS, SD, o ...
19-83 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D297 Perform a Manual Spa n Upgrade on an Unprotected Span Step 9 V erify that the transmit signal f alls wit hin the acceptabl e range. See T able 2-4 on page 2-17 for STM-N card transmit and recei v e le v els. Step 10 Complete the “NTP-D19 Install Fi ...
19-84 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D298 Check th e Network for Alar ms and Conditions Step 6 When you ha ve f inished Steps 3 through 5 for bo th nodes, install the ne w STM-N cards in both endpoints and attach the f iber to t he cards. W ait for the IM PR OPRMVL alarm to clea r and the ca ...
19-85 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D299 Initiate an M S-SPRing Span Lockout DLP-D299 Initiate an MS-SPRing Span Lockout Caution T raf f ic is not protected during a span lockout. Step 1 From the V iew men u, choose Go to Network V i ew . Step 2 Click the Pro visioning > MS-SPRing tabs. ...
19-86 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D299 Initiate an MS-SPRing Span Lockout Step 6 From the File menu, choose Close . Step 7 Return to your ori ginating procedure (NTP). ...
Cisco Systems D200のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- D200の取扱説明書
- Cisco Systemsの製品カード
- パンフレット
- またはCisco Systems D200の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Cisco Systems D200の取扱説明書に含まれています。
取扱説明書と呼ばれる文書のグループは、Cisco Systems D200の取り付け説明書、サービスマニュアル、簡易説明書、またはCisco Systems D200のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Cisco Systems D200の製品を使用するにあたって最も人気のある説明書を閲覧できます。
Cisco Systems D200デバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがCisco Systems D200を使用するのを助ける技術的文書のことです。説明書は通常、全てのCisco Systems D200ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。
Cisco Systemsの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。
1. Cisco Systems D200の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははCisco Systems D200の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Cisco Systems D200に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Cisco Systems D200デバイスの基本機能を使うにあたってのヒント。 Cisco Systems D200のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Cisco Systems D200に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるCisco Systems D200のメーカー/サービスへの連絡先に関する情報。
Cisco Systems D200についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもCisco Systems D200の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがCisco Systems D200で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。