-
Porter-Cable 330 - page 1
Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No. ______________________________________ Type ___________________________________________ Serial No. _______________________________________ IMPORTANT Please make certain tha ...
-
Porter-Cable 330 - page 2
2 WARNING: SOME DUST CREATED BY POWER SANDING, SAWING, GRINDING, DRILLING, AND OTHER CONSTRUCTION ACTIVITIES contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: · lead from lead-based paints, · crystalline silica from bricks and cement and other masonry products, and · arsenic ...
-
Porter-Cable 330 - page 3
3 2. Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts. 3. Avoid accidental starting. Be sure switch is OFF before plugging in. Carrying tools with your finger on the switch or plugging in tools tha ...
-
Porter-Cable 330 - page 4
4 SPECIFIC SAFETY RULES AND SYMBOLS 1 . HOLD TOOL BY INSULATED GRIPPING SURFACES WHEN PERFORMING AN OPERATION WHERE THE CUTTING TOOL MAY CONTACT HIDDEN WIRING OR ITS OWN CORD. Contact with a “live” wire will also make exposed metal parts of the tool “live” and shock the operator. 2 . ALWAYS DISCONNECT THE SANDER CORD PLUG FROM THE POWER CIR ...
-
Porter-Cable 330 - page 5
........................ watertight construction …/min ........................ revolutions or reciprocation per minute ADDITIONAL SAFETY RULES FOR PAINT REMOVAL WARNING: Extreme care should be taken when removing paint. The peelings, residue, and vapors of paint may contain lead, which is poisonous. Exposure to even low levels of lead can cause ...
-
Porter-Cable 330 - page 6
6 REPLACEMENT P ARTS When servicing use only identical replacement parts. MOTOR Many Porter-Cable tools will operate on either D.C., or single phase 25 to 60 cycle A.C. current and voltage within plus or minus 5 percent of that shown on the specification plate on the tool. Several models, however, are designed for A.C. current only. Refer to the sp ...
-
Porter-Cable 330 - page 7
In general, coarser grit sizes will remove the most material and finer grit sizes will produce the best finishes. Naturally, in all sanding operations, best results will be obtained if you select the proper size and type of abrasives. Only garnet, aluminum oxide and silicon carbide are recommended for use with finishing sanders. Flint paper is not ...
-
Porter-Cable 330 - page 8
8 4. While holding sander firmly and off of work surface, slide switch (A), Fig. 3, to the “ON” position. 5. Allow sander to reach full speed. Set it down on the work evenly and move it slowly back and forth in wide overlapping arcs (see SANDING PROCEDURE). 6. When you are finished sanding, lift sander up off work and slide switch (A), Fig. 3, ...
-
Porter-Cable 330 - page 9
9 wide, overlapping arcs. Do not concentrate on small areas. If liquid removers or heaters are used to speed the work, be sure the surface is cool and dry and the excess material has been scraped away with a putty knife or other suitable scraping tool before applying the sander. CABINETS AND DOORS The orbital motion of the Porter-Cable Finishing Sa ...
-
Porter-Cable 330 - page 10
10 Any loss of power before the above maintenance check may indicate the need for immediate servicing of your tool. DO NOT CONTINUE TO OPERATE TOOL UNDER THIS CONDITION. If proper operating voltage is present, return your tool to the service station for immediate service. SERVICE AND REP AIRS All quality tools will eventually require servicing or r ...
-
Porter-Cable 330 - page 11
The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): BAMMER ® , LASERLOC ® , OMNIJIG ® , POCKET CUTTER ® , PORTA-BAND ® , PORTA-PLANE ® , PORTER-CABLE ® , QUICKSAND ® , SANDTRAP ® , S ...
Porter-Cable 330についてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもPorter-Cable 330の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPorter-Cable 330で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。