Huffy DCM230の取扱説明書

18ページ 0.53 mb
ダウンロード

ページに移動 of 18

Summary
  • Huffy DCM230 - page 1

    12/02 P/N 211446D 1 T oll-Free Customer Service Number for U.S: 1-800-558-5234 Internet Address: http://www .hydra-rib.com IMPORT ANT! Have any questions?...Don’t go back to the store! We appreciate your purchasing one of our many fine products. We are sure that you will be very satisfied with your selection. Although great care and effort have b ...

  • Huffy DCM230 - page 2

    2 P/N 211446D 12/02 IMPORT ANT! WRITE MODEL NUMBER FROM BOX ONT O P AGE 1 OF THIS OWNERS MANUAL W ARNING F AILURE T O FOLLO W THESE W ARNINGS MA Y RESUL T IN SERIOUS INJUR Y AND/OR PROPER TY D AMA GE. Owner must ensure that all pla yers kno w and follow these rules for saf e operation of the system. • See instruction manual f or proper installati ...

  • Huffy DCM230 - page 3

    24" (61 cm) 36" (91.4 cm) Ensure ground is level with playing surface, then dig pole hole. GROUND SURFACE PLAYING SURFACE 1. Install threaded ends of J-bolts (1) through holes in mounting plate (3) and secure as shown. NOTE: Make sure J-bolts (1) are in the illustrated position. NOTE: Nuts on the top of plate are used for leveling the pol ...

  • Huffy DCM230 - page 4

    4 P/N 211446D 12/02 Fill hole with concrete. Tamp down concrete to release air pockets and build drainage hill. Insert J-bolts (1) from mounting plate (3) into cement as shown. Move assembly around to release any air pockets in cement, then rest mounting plate on cement drainage hill. Apply some pressure to level mounting plate on top of drainage h ...

  • Huffy DCM230 - page 5

    5 12/02 P/N 211446D Upright pole (5). Assemble lower pole flange onto protruding J-bolts (1) as shown. The flange will then rest on the nuts (2) from Step 2. Secure pole (5) flange to mounting plate (3) as shown. Tighten completely. 6. 7. 5 THREE PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY I ...

  • Huffy DCM230 - page 6

    6 P/N 211446D 12/02 8. Insert caps (8) into end of each support arm (9 & 10) as shown. Tap firmly in position. Apply logo label (11) to lower support arms (10) as shown. Repeat for opposite side. Beginning with upper support arms (9) secure support arms to pole. Continue by securing lower support arms (10) as shown. 9. IMPOR T ANT! Do not over ...

  • Huffy DCM230 - page 7

    7 12/02 P/N 211446D 1 1. 16 14 3 9 14 7 13 14 10 7 14 10 7 14 16 14 7 14 9 16 14 16 THREE PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. WARNING IMPOR T ANT! Do not over tighten. Secure H-frame board assembly to support arms (9 & 10). ...

  • Huffy DCM230 - page 8

    Position U-joint of crank jack (20) as shown. Where tubes on crank jack join, hold steady to keep both tubes from rotating. Rotate handle clockwise on crank jack to the fully extended position. Upright crank jack. 8 P/N 211446D 12/02 12. Secure jack brackets (17 & 18) to lower holes in pole as shown. 7 14 17 14 18 15 15 14 14 7 13. REAR VIEW IM ...

  • Huffy DCM230 - page 9

    9 12/02 P/N 211446D 14. Install crank jack (20) U-joint to lower set of support arms (10) as shown. 10 14 20 7 14 21 12 10 THREE PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. WARNING REAR VIEW IMPOR T ANT! Do not over tighten. ...

  • Huffy DCM230 - page 10

    10 P/N 211446D 12/02 15. Rotate jack handle clockwise to raise H-frame (13) to approximately 7’ (2.1 m) from ground. Secure crank jack (20) to jack brackets (17 &18) as shown. NOTE: Some adjustment will be necessary to align the lower crank jack bushing to jack brackets (17 & 18). THREE PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLL ...

  • Huffy DCM230 - page 11

    11 12/02 P/N 211446D RIM ASSEMBL Y & INST ALLA TION WARNING 17. Install carriage bolt (41) through rim (25), washers (4) and (27) as shown. Tighten nut (43) completely. Place nut (42) about half-way up carriage bolt (41) as shown. 25 4 41 27 43 TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BO ...

  • Huffy DCM230 - page 12

    12 P/N 211446D 12/02 20. 25 39 40 Insert spacer (45) through rim assembly (25). Place rim assembly on bracket (39) so that carriage bolt (41) is inserted through hole on top of inner bracket (40). Install hex bolt (44), washers (27) and nut (42) through top holes on bracket (39) through spacer (45) as shown.Tighten completely. Install rubber gromme ...

  • Huffy DCM230 - page 13

    13 12/02 P/N 211446D 22. 23. 24. Apply logo label (33) to cover plate (31). Install cover plate (18) on rim (25) using self tapping screws (32) as shown. LEVELING INSTRUCTIONS: Place level on rim (25) and adjust nut (42) until level. Tighten nut (30) to set rim tension for playing. Secure net (34) to rim (25). 1 2 3 34 25 NOTE ORIENT A TION OF COVE ...

  • Huffy DCM230 - page 14

    14 P/N 211446D 12/02 Apply height adjustment label (37) to front of pole as shown. 26. 10 feet (3.05 m) REGULATION RIM HEIGHT IS 10 FEET (3.05 m). 37 25. Check leveling at this time. Pole should be level in all directions. NOTE: If adjustment is necessary, adjust system by rotating the nuts (2) between mounting plate (3) and pole flange. (Refered t ...

  • Huffy DCM230 - page 15

    15 12/02 P/N 211446D 27. A. LOWER BACKBOARD UNTIL RIM IS 7 FEET OFF THE GROUND. B. APPLY THIN WHITE STRIP TO BOTTOM EDGE OF OUTER CRANK TUBE AS SHOWN. C. APPLY LARGE DECAL TO BACK OF POLE SO THAT 7 FOOT MARK ON LARGE DECAL IS LINED UP WITH THIN WHITE STRIP. Add height adjustment decal (35) ADDING HEIGHT INDICA T ORS B ...

  • Huffy DCM230 - page 16

    16 P/N 211446D 12/02 Rotate crank handle to raise and lower backboard. NOTE: If height adjustment is difficult to operate, you may have over tightened the areas indicated. Refer to Step 10 and Step 14. 29. Secure pole pad (36) as shown. 28. 36 Height Adjustment NOTE: Pole pad may NOT be included in this model. ...

  • Huffy DCM230 - page 17

    17 12/02 P/N 211446D Item Qty. Part No. Description 1 4 200573 J-Bolt, 5/8”-11” 2 12 265575 Nut, Hex 5/8”-11” 3 1 920880 Mounting Plate 4 8* 203470 Washer, Flat 5/8” I.D. x 1.5” O.D. 5 1 980880 Pole 6 1 200544 Pole Cap, Square 7 10* 206340 Nylon Insert Lock Nut, Hex 1/2”-13 8 8 220589 Cap, Arm Support Insert 9 2 916880 Support Arm, 42 ...

  • Huffy DCM230 - page 18

    18 P/N 211446D 12/02 Item #41 (1) Item #24 (8) Item #30 (1) Item #32 (2) Item #28 (1) Item #23 (4) Item #42 (2) HARDW ARE I DENTIFIER Item #44 (1) Item #45 (1) Item #43 (1) WARRANTY CARD: Please remember to complete your product registration form on-line at: www.hydrarib.com/warrantycard Item #27 (5)* ...

メーカー Huffy カテゴリー Fitness Equipment

Huffy DCM230のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- DCM230の取扱説明書
- Huffyの製品カード
- パンフレット
- またはHuffy DCM230の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Huffy DCM230の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Huffy DCM230の取り付け説明書、サービスマニュアル、簡易説明書、またはHuffy DCM230のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Huffy DCM230の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Huffy DCM230デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがHuffy DCM230を使用するのを助ける技術的文書のことです。説明書は通常、全てのHuffy DCM230ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Huffyの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Huffy DCM230の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははHuffy DCM230の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Huffy DCM230に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Huffy DCM230デバイスの基本機能を使うにあたってのヒント。 Huffy DCM230のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Huffy DCM230に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるHuffy DCM230のメーカー/サービスへの連絡先に関する情報。

Huffy DCM230についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもHuffy DCM230の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHuffy DCM230で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)