-
HSM HSM FA 400.2 - page 1
OPERA TING MANUAL SHREDDER HSM F A 400.2 english Keep in a safe place for future use! 1.513.999.1 12 – 0702 ...
-
HSM HSM FA 400.2 - page 2
2 0702 F A 400.2 Contents 1. Proper use, warranty ................................................................................................................. 3 2. Safety instructions ..................................................................................................................... 3 3. Overview ............................. ...
-
HSM HSM FA 400.2 - page 3
0702 3 F A 400.2 Danger of injury Do not reach into the paper feed opening. Splinters can cause injury Before destroying credit cards and store cards, CD-ROMs or fl oppy disks, you must fi t a splinter guard (strip curtain, order no. 1.513.050.445). Danger of injury during intake Do not go near the paper feed open- ing with long hair , loose clot ...
-
HSM HSM FA 400.2 - page 4
4 0702 F A 400.2 3. Overview 1 Main switch (only solo-version) 2 Keypad 3 Emergency stop button 4 Loading tray 5 Option: extra-wide work table 6 Left cover panel 7 Right cover panel 8 Intake conveyor , paper feed opening 9 Front door 10 Braking swivel castors 1 1 Oiler on particle cut machines 12 Nameplate 1 10 12 9 3 2 5 4 6 7 8 11 ...
-
HSM HSM FA 400.2 - page 5
0702 5 F A 400.2 4. Dimensions HSM F A 400.2 Solo version 1564 1646 1208 804 1 157 HSM F A 400.2 Combi version 1644 1646 1208 804 1 157 Transportation dimensions (without tray) Space requirements for operation and maintenance 804 1262 1646 800 200 1557 200 2414 ...
-
HSM HSM FA 400.2 - page 6
6 0702 F A 400.2 5. T ransportation, installation • Place the shredder in its packaging on a smooth, level surface. • Remove the packaging. • If you need to move the shredder through narrow doors, you can wait until it is at its fi nal location before fi tting the loading tray . Without the tray , the machine is only 805 mm wide. • When m ...
-
HSM HSM FA 400.2 - page 7
0702 7 F A 400.2 Ready for operation Green LED W aste bag full Red LED Start button The shredder switches on. The feed belt moves in the intake direction. Stop button The cutting block and feed belt stop. The shredder is in standby mode. Reverse button The cutting block and feed belt run in reverse. Paper jam or overload Red LED Door open Red LED 7 ...
-
HSM HSM FA 400.2 - page 8
8 0702 F A 400.2 Place the material to be shredded on the loading tray and then place batches on the feed belt. If material that is not supposed to be shred- ded is mistakenly placed onto the belt, never attempt to pull it out. • Press the stop button. The drive stops. • Press the reverse button. The cutting block and feed belt run in r ...
-
HSM HSM FA 400.2 - page 9
0702 9 F A 400.2 8. Malfunctions Check the following before calling customer service: • Is the power plug connected? • Is the shredder switched on? • Is the front door closed? • Is the waste bag full? • Is there a paper jam in the shredder? • Has the motor been overloaded? Paper jam (excessive paper feed) The red LED on the keypad b ...
-
HSM HSM FA 400.2 - page 10
10 0702 F A 400.2 Note: Do not tighten the chain too much, as this will cause premature wear on the chain and bearings. 9. Maintenance and care Cleaning the cutting block Strip cut machines: (1 x daily) • Switch off the shredder . • Squirt special cutting apparatus oil through the paper feed opening onto the blade roll- ers. Order no. 1.235.997 ...
-
HSM HSM FA 400.2 - page 11
0702 11 F A 400.2 Greasing the drive chains and cogs (twice yearly) • Switch off the shredder . • Pull out the power plug. • Remove the tray and the cover panels. • Grease the cogs and the drive chains from the motor to the cutting apparatus, the cut- ting block to the feed belt and the cutting block to the regulating roller . Recommended l ...
-
HSM HSM FA 400.2 - page 12
12 0702 F A 400.2 1 1. T echnical data 10. Scope of supply , accessories • Machine on pallet with a wooden frame, strapped with packing tape and packed in foil • 4 waste bags, order no. 1.513.995.000 for 2-chamber system (Solo version) • 1 waste bag, order no. 1.513.995.100 for 1-chamber system (Solo version) • Special cutting block oil For ...
-
HSM HSM FA 400.2 - page 13
0702 13 F A 400.2 12. Electric wiring diagrams 400 V / Sol o Legend: =A V : Shredder +S: in switch cabinet +MA: on machine +BF: Keypad Solo 400 V / 50 Hz ...
-
HSM HSM FA 400.2 - page 14
14 0702 F A 400.2 400 V / Sol o ...
-
HSM HSM FA 400.2 - page 15
0702 15 F A 400.2 400 V / Sol o ...
-
HSM HSM FA 400.2 - page 16
16 0702 F A 400.2 Combination 400 V / 50 Hz ...
-
HSM HSM FA 400.2 - page 17
0702 17 F A 400.2 ...
-
HSM HSM FA 400.2 - page 18
18 0702 F A 400.2 ...
-
HSM HSM FA 400.2 - page 19
0702 19 F A 400.2 ...
-
HSM HSM FA 400.2 - page 20
20 0702 F A 400.2 Declaration of Conformity Machinery directive 98 / 37 / EG EMC directive 89 / 336 / EWG Low voltage directive 73 / 23 / EWG The manufacturer HSM GmbH + Co. KG, Bahnhofstrasse 1 15, D-88682 Salem declares herewith, that the paper shredder (Solo machine) HSM F A 400.2 corresponds with the above mentioned EC Machine Directive includi ...
HSM HSM FA 400.2についてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもHSM HSM FA 400.2の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHSM HSM FA 400.2で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。