日本語 dropdown-ico

NEC MultiSync LCD8205-Pの取扱説明書

28ページ 5.3 mb
ダウンロード

ページに移動 of 28

Summary
  • NEC MultiSync LCD8205-P - page 1

    User ’ s Manual MultiSync LCD8205 MultiSync LCD8205-P ...

  • NEC MultiSync LCD8205-P - page 2

    Index Declaration of conformity ...................................................................................................... ....................... English-1 Important Information .......................................................................................................... ......................... English-2 W arning, Cautio ...

  • NEC MultiSync LCD8205-P - page 3

    English-1 English For USA FCC Information 1. Use the attached specified cables with the MultiSync LCD8205 (L828N0)/MultiSync LCD8205-P (L828N0) color display so as not to interfere with radio and television reception. (1) Please use the supplied power cord or equivalent to ensure FCC compliance. (2) Please use the supplied shielded video signal cab ...

  • NEC MultiSync LCD8205-P - page 4

    English-2 Important Information TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT T O RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPT ACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULL Y INSER TED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOL T AGE COMPONENTS INSIDE. REFER SERVICING T ...

  • NEC MultiSync LCD8205-P - page 5

    English-3 English FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE MUL TI-FUNCTION MONITOR: • DO NOT OPEN THE MONITOR . There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel. • Do not s ...

  • NEC MultiSync LCD8205-P - page 6

    English-4 Contents Power Cord* 1 Setup Manual DVI-D to DVI-D cable Wireless Remote Control and AAA Batteries Clamp Y our new MultiSync LCD monitor box* should contain the following: • LCD monitor • Power Cord* 1 • V ideo Signal Cable • Setup Manual • Wireless Remote Control and AAA Batteries • Clamp • Screw for clamp (M4 x 10) x 2 • ...

  • NEC MultiSync LCD8205-P - page 7

    English-5 English This de vice cannot be used or installed without the T abletop Stand or other mounting accessor y f or suppor t. F or proper installation it is strongly recommended to use a trained, NEC authorized service person. F ailure to follo w NEC standard mounting procedures could result in damage to the equipment or injury to the user or ...

  • NEC MultiSync LCD8205-P - page 8

    English-6 4. Attach Mounting Accessories The display is designed for use with the VESA mounting system. When using mounting accessories other than NEC compliant and approved, they must comply with the VESA- compatible mounting method. NEC strongly recommends using screws M8 size and 10 - 18 mm in length. If using screws longer than 18 mm, check the ...

  • NEC MultiSync LCD8205-P - page 9

    English-7 English 1 POWER button ( ) Switches the power on/off. 2 CH +/- button Acts as button to move the highlighted area up or down to select adjustment items within OSD menu. 3 VOL +/- button Increases or decreases audio output level. Increases or decreases the adjustment level within OSD menu settings. 4 SEL button Enter Input Source OSD menu, ...

  • NEC MultiSync LCD8205-P - page 10

    English-8 T erminal Panel 1 HDMI connector T o input digital HDMI signals. 2 DVI IN (DVI-I) T o input digital or analogue RGB signals from a computer . 3 SPDIF Optical digital audio out for HDMI input only . 4 EXTERNAL CONTROL (D-Sub 9 pin) Connect RS-232C input from external equipment such as a PC in order to control RS-232C functions. 5 Audio Inp ...

  • NEC MultiSync LCD8205-P - page 11

    English-9 English NOTE: The button without explanation doesn’t work. 1 POWER button Switches the power on/off. 2 SOURCE button Enter Input Source OSD menu, [DVI], [PC], [HDMI], [A V1], [A V2], [S-Video] and [Component]. 3 MUTE button T urns on/off mute function. 4 INFO button T urns on/off the information OSD. 5 STILL button T oggles picture stat ...

  • NEC MultiSync LCD8205-P - page 12

    English-10 1. Determine the installation location CAUTION: Installing your LCD display must be done by a qualified technician. Contact your dealer for more information. CAUTION: IN ORDER T O AID IN MOUNTING, A LIFTING DEVICE MUST BE USED IN CONJUNCTION WITH THE A TT ACHABLE EYEBOL TS. MOVING OR INST ALLING THE LCD MONIT OR MUST BE DONE BY FOUR OR M ...

  • NEC MultiSync LCD8205-P - page 13

    English-11 English 5. Switch on the power of all the attached external equipment When connected with a computer , switch on the power of the computer first. 6. Operate the attached external equipment Display the signal from the desired input source. 7. Adjust the sound Make volume adjustments when required. 8. Adjust the screen (See page 18) Make a ...

  • NEC MultiSync LCD8205-P - page 14

    English-12 Connections Before making connections: * First turn off the power of all the attached equipment and make connections. * Refer to the user manual included with each separate piece of equipment. Connecting a Personal Computer Connecting your computer to your LCD monitor will enable you to display your computer’s screen image. Some video ...

  • NEC MultiSync LCD8205-P - page 15

    English-13 English Connect the LCD Monitor to a DVD Player • T o connect the Component connector (RCA) on the LCD monitor , use an RCA connector cable (sold separately). Connecting a DVD Player with component out Connecting your DVD player to your LCD monitor will enable you to display DVD video. Refer to your DVD player user ’s manual for more ...

  • NEC MultiSync LCD8205-P - page 16

    English-14 Connecting to a Stereo Amplifier Y ou can connect your stereo amplifier to your LCD monitor . Refer to your amplifier owner ’s manual for more information. LCD monitor Amplifier External speaker External speaker Connecting a DVD Player with HDMI out Connecting your DVD player to your LCD monitor will enable you to display DVD video. Re ...

  • NEC MultiSync LCD8205-P - page 17

    English-15 English Basic Operation Power ON and OFF Modes The LCD monitor power indicator will turn green while powered on and will turn red while powered off. Power Button ...

  • NEC MultiSync LCD8205-P - page 18

    English-16 Power Indicator Mode Power ON Power OFF (Standby)* Power consumption under 1W Power Save Power consumption under 15W Not connected Using Power Management The LCD monitor follows the VESA approved DPM Power Management function. The power management function is an energy saving function that automatically reduces the power consumption of t ...

  • NEC MultiSync LCD8205-P - page 19

    English-17 English OSD (On-Screen-Display) Controls Press MENU button to show OSD menu. Press UP and DOWN to select the main menu. Press Right button to enter the sub menu. Press EXIT to exit menu. Remote Control Press MENU button to show OSD menu. Press CH+ and CH- buttons to select the main menu. Press VOL+ button to enter the sub menu. Press MEN ...

  • NEC MultiSync LCD8205-P - page 20

    English-18 OSD Setting Picture Picture Mode User Store last value at User setting. Dynamic Selection of the picture appearance. Standard Movie Mild User Brightness Adjust the brightness. Contrast Adjust the Contrast. Color (A V1/A V2/S-Video/Component) Adjust the Color . T int (A V1/AV2/S-V ideo/Component) Adjust the T int. Sharpness Adjust the Sha ...

  • NEC MultiSync LCD8205-P - page 21

    English-19 English Sound Mode User This function use setting Equalizer value. Standard Selection of preset Sound mode (Equalizer). Music Movie Speech V olume Adjust the sound volume level. Balance T uning the sound balance between left and right. Equalizer 10 KHz The value of 5 Band equalizer are preset. 3 KHz These values are changed by user with ...

  • NEC MultiSync LCD8205-P - page 22

    English-20 Advanced Dimming Auto Dimming Enable/Disalbe Auto Dimming control by Abient Light sensor . Dim Level Display current Dim Level. MAX Dim Ambient Adjusts detected light ambient to set the maximun dimming. MIN Dim Ambient Adjusts detected light ambient to set the minimun dimming. Ambient Display current detected light ambient level by Lux u ...

  • NEC MultiSync LCD8205-P - page 23

    English-21 English Controlling the LCD monitor via RS-232C Remote Control This LCD monitor can be controlled by connecting a personal computer with a RS-232C terminal. Functions that can be controlled by a personal computer are: • Power ON or OFF • Switching between input signals Connection LCD Monitor + PC NOTE: If your PC (IBM or IBM compatib ...

  • NEC MultiSync LCD8205-P - page 24

    English-22 Features Color Control Systems: Allows you to adjust the colors on your screen and customize the color accuracy of your monitor to a variety of standards. OSD (On-Screen-Display) Controls: Allow you to quickly and easily adjust all elements of your screen image via simple to use on-screen menus. Plug and Play: The Microsoft ® solution w ...

  • NEC MultiSync LCD8205-P - page 25

    English-23 English T roubleshooting No picture • The signal cable should be completely connected to the display card/computer . • The display card should be completely seated in its slot. • Front Power Switch and computer power switch should be in the ON position. • Check to make sure that a supported mode has been selected on the display c ...

  • NEC MultiSync LCD8205-P - page 26

    English-24 Specifications Product Specifications LCD Module 81.6"/207 cm diagonal Pixel Pitch: 0.744 mm Resolution: 1920 x 1080 dots Color: Over 16 million colors (depending on video card used) Brightness: 600 cd/m 2 (T yp.) (LCD8205)/450 cd/m 2 (T yp.) (LCD8205-P) Contrast Ratio: 2000:1 Viewing Angle: 89° (typ) @ CR>10 (LCD8205)/85° (typ ...

  • NEC MultiSync LCD8205-P - page 27

    English-25 English Pin Assignment 1) S-VIDEO input: VIDEO Pin No Name 1G N D 2G N D 3 Y (Luminance) 4 C (Chroma) 2) Digital/Analog RGB input: DVI-I 3) RS-232C input Pin No Name 1 connected to 7&8 2 RXD 3 TXD 4 connected to 6 5G N D 6 connected to 4 7 connected to 1&8 8 connected to 1&7 9N C Pin - Assignment of DVI connector: 1 TX2- 9 TX ...

  • NEC MultiSync LCD8205-P - page 28

    English-26 NEC DISPLA Y SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’ s top priorities in trying to minimize the burden placed on the environment. W e are engaged in developing environmentally- friendly products, and always strive to help define and comply with the latest independent standar ...

メーカー NEC カテゴリー Computer Monitor

NEC MultiSync LCD8205-Pのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- MultiSync LCD8205-Pの取扱説明書
- NECの製品カード
- パンフレット
- またはNEC MultiSync LCD8205-Pの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、NEC MultiSync LCD8205-Pの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、NEC MultiSync LCD8205-Pの取り付け説明書、サービスマニュアル、簡易説明書、またはNEC MultiSync LCD8205-Pのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、NEC MultiSync LCD8205-Pの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

NEC MultiSync LCD8205-Pデバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがNEC MultiSync LCD8205-Pを使用するのを助ける技術的文書のことです。説明書は通常、全てのNEC MultiSync LCD8205-Pユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

NECの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. NEC MultiSync LCD8205-Pの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははNEC MultiSync LCD8205-Pの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。NEC MultiSync LCD8205-Pに関してこのドキュメントで見つけることができる全てのヒントの目次
3. NEC MultiSync LCD8205-Pデバイスの基本機能を使うにあたってのヒント。 NEC MultiSync LCD8205-Pのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。NEC MultiSync LCD8205-Pに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるNEC MultiSync LCD8205-Pのメーカー/サービスへの連絡先に関する情報。

NEC MultiSync LCD8205-Pについてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもNEC MultiSync LCD8205-Pの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがNEC MultiSync LCD8205-Pで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)