Aussie 3 ELITEの取扱説明書

25ページ 1.36 mb
ダウンロード

ページに移動 of 25

Summary
  • Aussie 3 ELITE - page 1

    Aussie ® by Meco ® LP Gas Grill Assembly and Use Manual For Customer Service, call 1-800-251-7558 or visit our web site at www .aussiegrill.com FOR OUTDOOR HOUSEHOLD USE ONL Y . NOT FOR COMMERCIAL USE. • Failure to follow these instructions could result in fire or explosion which could cause death, serious personal injury , or property damage. ...

  • Aussie 3 ELITE - page 2

    2 I. Assembly Instructions.......................................................2 Parts Illustrations................................................................3 S tep 1) Legs/Side T able Assy .............................................5 S tep 2) Install LP Cylinder S torage Guard .........................6 S tep 3) Assemble Bottom Shelf to ...

  • Aussie 3 ELITE - page 3

    3 STEP 1) Legs/Side T able Assembly: Att ach the Wheel and Caster Legs to the Side T ables with 1/4-20 x 1-3/8” Bolt s through the legs into threaded insert in side t ables. Position legs exactly as shown. Do not completely tighten bolt s. Wheel Legs and Side T able Assembly T o reduce the risk of injuries: · Wear protective gloves when handling ...

  • Aussie 3 ELITE - page 4

    4 (9) Bottom Shelf 1 pc (8) Bolt, 1/4-20 x 1/2” 2 pc STEP 2) Inst all LP Cylinder Storage Guard: Place the LP Cylinder W ire Guard at an angle through the first and second to last openings of the Bottom Shelf. (FIG . 2A) From the bottom side align the Wire rings with the threaded insert s in the Bottom Shelf. (FIG . 2B) Inst all the two 1/4-20 x ...

  • Aussie 3 ELITE - page 5

    5 Step 3) Assemble Bottom Shelf to Legs: • Place the Leg/Side T able/LegAssemblies opposite each other with the velcro p atches on same side. (FIG . 3) • Place Bottom Shelf up side down inside the Legs. Align the bolt holes of the Bottom Shelf and Legs. Fasten with the 1/4-20 x 1-3/8” bolt s, but do not tighten completely . Note: Do not align ...

  • Aussie 3 ELITE - page 6

    6 (13) Axle 1 pc (14) Wheel Assembly 2 pc (1 1) Caster Wheel 2 pc Step 4) Assemble Wheels, Casters, and LP Cylinder Support: • Thread Caster Wheels into the Right Side Legs and tighten securely using a 3/4” wrench or socket. (FIG . 4A) • Place Cylinder Support on bottom side of Cart Assembly with Cylinder Lock Bolt towards the end of the Cart ...

  • Aussie 3 ELITE - page 7

    7 (16) Bottom Body Panel 1 pc (15) Grill Body 1 pc (18) Sp acer 8 pc (19) Wingnut, M6 8 pc Step 5) Assemble Grill Body to Cart: • Remove the Bottom p anel from the Grill Body . • Lay Grill Body on it s back with the control panel facing up. Place Cart Assembly Legs around the Grill Body . (FIG . 5A) • Align slotted holes on sides of Grill Bod ...

  • Aussie 3 ELITE - page 8

    8 Step 6) Inst all Control Knobs, Fabric Panel, and Hood Handle: • Align the flat keyed hole in the Control Knobs with the keyed stem of the Control valves. Push the Control Knobs onto the V alve stem. (FIG . 6A) • Open the Hood and position the handle with the bolt heads facing up. Align the threaded holes in the handle with the two holes in t ...

  • Aussie 3 ELITE - page 9

    9 Step 7) Inst all Bottom Panel and Grease T ray: Slide the Bottom Panel into the track at the bottom of the grill body . (FIG . 7A) Secure Bottom Panel into Body Assembly with a ST 4.0 x 10 Screw on each side. (FIG . 7B) Insert the Foil Pan into the Grease T ray and slide the Grease T ray into the guides of the Bottom Panel all the way . (FIG . 7C ...

  • Aussie 3 ELITE - page 10

    Step 9) Inst all Cooking Grids: Place Cooking Grids onto the front and back Bowl ridges over the Flame Diffusers and Main Burners. (FIG . 9) 10 Step 8) Inst all Flame Diffuser: Place a Flame Diffuser in the guides over each Burner . (FIG . 8) (28) Flame Diffuser ( 29) Cooking Grid ( 29) Cooking Grid FIG . 8 FIG . 9 Flame Diffuser Guides ...

  • Aussie 3 ELITE - page 11

    11 T o reduce the risk of serious bodily injury or death: · Use only prop ane gas in this LP gas grill. · Do not attempt to convert an LP unit to natural gas. · Any use or alteration of this unit not intended could be unsafe and will void your warranty . · Always use a gas appliance outdoors in an open area with good ventilation to avoid breath ...

  • Aussie 3 ELITE - page 12

    4) T urn the adjusting knob clockwise to secure LP cylinder inside support bracket. (FIG . 13A) 12 FIG . 10A FIG . 10B 5) Remove the protective cap from the LP cylinder valve. (Save cap for re-capping.) Make sure all control Knobs are turned “OFF”. Hold Regulator in a straight line with LP cylinder valve so the connection does not cross thread. ...

  • Aussie 3 ELITE - page 13

    13 How to perform a leak test: Supplies Needed for a Leak T est: Clean paint brush, water and dish washing liquid. 1) Use an LP Cylinder equipped with an OPD (Overfill Prevention Device) and have it filled at an authorized LP gas dealer by a qualified attendant. 2) Make sure all of the grill control panel knobs are turned to the “off” position ...

  • Aussie 3 ELITE - page 14

    14 6. If any of the burners fail to light,repeat S tep 4. The burner should light within three or four attempts. If any or all burners fail to light after three or four attempt s following S teps 4-6, turn all knobs to the “Of f” position and close the LP gas cylinder valve to dissip ate any accumulated gas. W ait five minutes; then repeat the ...

  • Aussie 3 ELITE - page 15

    15 CHECK YOUR FLAME Y ellow T ip Primarily Blue Flame Y our burners have been preset by the manufacturer for opti- mal flame performance. A blue flame, possibly with a small yellow tip, is the result of the optimal air and gas mixture. (FIG . 14) FIG . 14 Check the flame before each cooking session and throughout the grilling season. Always check e ...

  • Aussie 3 ELITE - page 16

    16 · If you notice grease or other hot material dripping from the grill onto the valve, hose, or regulator , turn off the gas supply immediately . After the grill has cooled, determine the cause and correct it. After cleaning the valve and hose and regulator assembly , perform a leak test before continuing use. (See Performing a Leak T est.) · Do ...

  • Aussie 3 ELITE - page 17

    S piders or small insects can build nest s, webs and lay eggs in the grills venturi tubes obstructing the flow of gas to the burner . The backed-up gas can ignite behind the control panel causing damage to the grill and even injury to the operator . This is known as a “flashback”. In order to prevent flashbacks, the burner(s) should be removed ...

  • Aussie 3 ELITE - page 18

    18 Lif t up and slide Burner back. FIG . 15D 9) Lift Burner up from the back and pull it towards the rear . In order to clear the warming rack, lean the burner to one side and gently pull the burner mouth away from the valve nozzle. (FIG . 15D) FIG . 15E 10) Slide the Electrode through the keyhole slot. (FIG . 15E) 1 1) Use a pipe cleaner to clear ...

  • Aussie 3 ELITE - page 19

    19 STORAGE T o reduce the risk of serious bodily injury or death: · Store your LP gas grill in a cool dry place. Do not store an LP gas cylinder in a sp ace greater than 125 degrees Fahrenheit. Do not store an LP gas cylinder in a building ,garage or any enclosed area. · Do not store an LP gas cylinder indoors (empty or filled). Disconnect the LP ...

  • Aussie 3 ELITE - page 20

    Problem: Possible Cause: Solution: Burner will not light using the Igniter Burner is not connected to V alve. Not pausing long enough before clicking the Ignitor Button No spark LP gas cylinder is empty LP Coupling nut is not fully connected to regulator LP Excess flow valve tripped in regulator Obstructions in burner Electrode and burner are wet W ...

  • Aussie 3 ELITE - page 21

    Gas in LP Cylinder is low Excess flow valve tripped in regulator Check LP gas cylinder . Refill if necessary . T urn control knobs to “off” position and turn LP gas cylinder handle clockwise until it stops. W ait five minutes. Relight LP gas grill. If flame continues to be low , turn of f gas at cylinder and grill. Disconnect the regulator from ...

  • Aussie 3 ELITE - page 22

    SER VICE P ARTS HOOD ASSEMBL Y TEMPERA TURE GUAGE HANDLE HINGE CONTROL KNOB COOKING GRID FLAME DIFFUSER BURNER CROSSOVER 22 BODY ASSEMBL Y IGNITER GREASE P AN BOTTOM P ANEL CONTROL P ANEL MANIFOLD ASSEMBL Y HOOD STOP REAR CASTER LEG FRONT CASTER LEG AXLE REAR WHEEL LEG PRIV ACY P ANEL WHEEL ASSEMBL Y CYLINDER GUARD CASTER CYLINDER SUPPORT BOTTOM SH ...

  • Aussie 3 ELITE - page 23

    SER VICE P ARTS 23 ...

  • Aussie 3 ELITE - page 24

    IMPORTANT NOTICE The Gas Grill is setup to operate with a LP Gas Cylinder equipped with an OPD (Overfill Prevention Device). This is a secondary device to prevent the overfill of your LP Gas cylinder . The proper methods for the filling of your LP Gas cylinder are by weight or volume, as described in NFP A 58. Please make sure your filling st ation ...

  • Aussie 3 ELITE - page 25

    MECO CORPORA TION LIMITED W ARRANTY This product is warranted to the original consumer purchaser against defects in material and workman- ship under normal outdoor household use and correct assembly (if assembled by the consumer-purchas- er). Burner and Cooking Grid are warranted for a period of one (1) year from the date of purchase. All other par ...

メーカー Aussie カテゴリー Gas Grill

Aussie 3 ELITEのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 3 ELITEの取扱説明書
- Aussieの製品カード
- パンフレット
- またはAussie 3 ELITEの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Aussie 3 ELITEの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Aussie 3 ELITEの取り付け説明書、サービスマニュアル、簡易説明書、またはAussie 3 ELITEのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Aussie 3 ELITEの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Aussie 3 ELITEデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがAussie 3 ELITEを使用するのを助ける技術的文書のことです。説明書は通常、全てのAussie 3 ELITEユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Aussieの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Aussie 3 ELITEの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははAussie 3 ELITEの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Aussie 3 ELITEに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Aussie 3 ELITEデバイスの基本機能を使うにあたってのヒント。 Aussie 3 ELITEのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Aussie 3 ELITEに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるAussie 3 ELITEのメーカー/サービスへの連絡先に関する情報。

Aussie 3 ELITEについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもAussie 3 ELITEの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがAussie 3 ELITEで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)