AMX noneの取扱説明書

52ページ 0.94 mb
ダウンロード

ページに移動 of 52

Summary
  • AMX none - page 1

    Control Panel Accessor ies WAVE 2 - Way Wireless Accessories and Adapters for Touch Panels Instruction Manual ...

  • AMX none - page 2

    Limited Warranty and Disclaimer Panja Inc. warrants its products to be free from defects in material and workma n ship under normal use for a period of three years from date of purchase from Panja, I n- co r porated, with the following exceptions. Electroluminescent and LCD control pa n- els are warranted for a period of three years, except for the ...

  • AMX none - page 3

    WAVE 2 - Way Wireless Accessories and Adapters for Touch Panels Table of Contents i Table of Contents Introduction ............................................................................ 1 Overview 1 Features 2 What’s in this Manual 2 What’s New 3 AXR - WAVES 3 WAV - PK 3 WAV - PKM 3 WAV - LNK WaveLink 4 WAV - PM WaveLink power module 4 Re ...

  • AMX none - page 4

    ii Table o f Contents WAVE 2 - Way Wireless Accessories and Adapters for Touch Panels AXR - W AVES (or WAV - LNK) Group ID DIP Switch 18 WAV - PK Group ID DIP switch 19 WAV - PKM Group ID DIP switch 20 Battery Charging 20 WAV - PM WaveLin k Power Module 21 Installation ............................................................................ 23 ...

  • AMX none - page 5

    WAVE 2 - Way Wireless Accessories and Adapters for Touch Panels Introduction 1 Introduction Overview The AXR - WAVES Wireless AXlink Virtual Emul ator Server ( Figure 1 ) is a 2 - way Radio Frequency (RF) device employing spread spectrum communications. A si n gle AXR - WAVES can communicate with up to 16 wireless TiltScreen touch panels equipped w ...

  • AMX none - page 6

    2 Introduction WAVE 2 - Way Wireless Accessories and Adapters for Touch Pa nels Addition ally, the WAV - LNK WaveLink transceiver ( Figure 2 ) may be used in co n- junction with one or more WAV - PM modules when a UniMount or rack mounted touch panel is used in a remote, wireless application. The WAV - LNK is ideal fo r U n- iMount touch panels mou ...

  • AMX none - page 7

    WAVE 2 - Way Wireless Accessories and Adapters for Touch Panels Introduction 3 What’s New Updates to this manual include: • Battery usage, safety warnings, and caution information • Updated technical support information All other revisions are identified by vertical margin bars as shown adjacent to this paragraph. AXR - WAVES AXR - WAVES feat ...

  • AMX none - page 8

    4 Introduction WAVE 2 - Way Wireless Accessories and Adapters for Touch Pa nels • Rechargeable lead - acid battery (WAV - PKM Mini - WavePack Battery) • Lithium battery maintains the flash RAM WAV - LNK WaveLink The WAV - LNK WaveLi nk transceiver features include: • 2 - way RF spread - spectrum communications with an AXR - WAVES server. • ...

  • AMX none - page 9

    WAVE 2 - Way Wireless Accessories and Adapters for Touch Panels Introduction 5 Sample Product Application The AXR - WAVES connects to a Central Controller and communicates with a wide variety of touch panels. The WAV - PK and WAV - PKM power packs co n nect to full - sized and mini - touch panels to provide mobility and communications with an AXR - ...

  • AMX none - page 10

    6 Introduction WAVE 2 - Way Wireless Accessories and Adapters for Touch Pa nels • AXlink — Green LED that blinks when there is AXlink communication a c ti v- ity. The green AXlink LED indicates the following power and data acti v it y: One blink per second: Power is active and AXlink data communication is functional. — Full on : Power is acti ...

  • AMX none - page 11

    WAVE 2 - Way Wireless Accessories and Adapters for Touch Panels Introduction 7 Rear panel The rear panel has an RF antenna and a 4 - pin AXlink bus connector. Figure 5 shows the AXR - WAVES rear panel. • ANTENNA — Right - angle, flexible, bi - directional RF antenna. • AXlink — Fou r - pin (male) connector connects to the Central Controller ...

  • AMX none - page 12

    8 Introduction WAVE 2 - Way Wireless Accessories and Adapters for Touch Pa nels Rear panel The WAV - PK rear panel provides a barrel power (plug - in) connector for operating or recharging of the unit. There is also a wake - up switch located in the center - rear of the WAV - PK. Figure 7 shows the rear of the unit and the power connector. ON 3 2 4 ...

  • AMX none - page 13

    WAVE 2 - Way Wireless Accessories and Adapters for Touch Panels Introduction 9 Rear panel The WAV - PKM rear panel provides a power connector for operating or recharging of the unit. Figure 9 shows the rear of the unit and the power connector. WAV - LNK WaveLink The WAV - LNK WaveLink transceiver provides an interface for up to 16 touch pa n- els o ...

  • AMX none - page 14

    10 Introduction WAVE 2 - Way Wireless Accessories and Adapters for Touch Pa nels Front panel Figure 10 shows the front panel for the WAV - LNK and its switches and indicators are described below. • AXlink — This LED lights when an active AXlink connection is esta b lished. • GROUP ADDRESS — Eight - position DIP switch sets the gr oup addres ...

  • AMX none - page 15

    WAVE 2 - Way Wireless Accessories and Adapters for Touch Panels Introduction 11 PWR 12VDC − + Optional WAV - PM WaveLink Power Module The WAV - PM WaveLink Power Module provides additional wireless backup power to a Wave Link device. WAV - PMs can be daisy - chained to provide 12 VDC at up to 10 A. The following paragraphs identify and define con ...

  • AMX none - page 16

    12 Introduction WAVE 2 - Way Wireless Accessories and Adapters for Touch Pa nels • Empty/Full gauge — The BATTERY indicator gauge (empty - full) provides a visual indication of the charge level of the battery currently being used. If the battery's charge is high, all left - to - right indicator lamps will be lit. • Test — Pressing the ...

  • AMX none - page 17

    WAVE 2 - Way Wireless Accessories and Adapters for Touch Panels Introduction 13 Power management The Wave Packs incorporate advanced power management schemes that reduce overall power consumption. Power management is software - controlled by the i n d i- vidual touch panel program. The user tells the WavePack when to go into power co n servation mo ...

  • AMX none - page 18

    14 Introduction WAVE 2 - Way Wireless Accessories and Adapters for Touch Pa nels Safe handling and usage of the battery To prevent deterioration or damage to the battery: • Do not use battery to power equipment other than the WAV - PK or WAV - PKM. • Do not drop or subject the battery to strong physical shock. • Do not use the battery below - ...

  • AMX none - page 19

    WAVE 2 - Way Wireless Accessories and Adapters for Touch Panels Introduction 15 Optional WAV - CHG Fast - Cycle Battery Charger The WAV - CHG Fast - Cycle Battery Charger is shown in Figure 17 . The charger will charge two batteries simultaneously. Refer to the Batte ry Charging subsection of this manual. The charger provides a fast - cycle, 4 - ho ...

  • AMX none - page 20

    16 Introduction WAVE 2 - Way Wireless Accessories and Adapters for Touch Pa nels ...

  • AMX none - page 21

    WAVE 2 - Way Wireless Accessories and Adapters for Touch Panel s Pre - Installation 17 Pre - Installation Overview B efore installing the wireless communications equipment, set the AXR - WAVES GROUP ADDRESS DIP switch. Then, set the GROUP ID DIP switches for the AXR - WAVES, WAV - LNK, WAV - PK, and WAV - PKM. Figure 18 shows the DIP switches o n t ...

  • AMX none - page 22

    18 Pre - Installation WAVE 2 - Way Wireless Accessories and Adapters for Touch Panels Figure 19 shows the AXR - WAVES GROUP ADDRESS DIP (or WAV - LNK) switch and a quick reference for the DIP switch numbers and their values. 1 2 3 4 5 6 7 8 ON GROUP ADDRESS DIP switch settings Switch Value 1 1 2 2 3 4 4 8 5 16 6 32 7 64 8 128 AXR - WAVES (or WAV - ...

  • AMX none - page 23

    WAVE 2 - Way Wireless Accessories and Adapters for Touch Panel s Pre - Installation 19 GROUP ID 1 2 3 4 ON DIP switch se t tings Switch Value 1 1 2 2 3 4 4 8 WAV - PK Group ID DIP switch The 4 - position group ID DIP switch ( Figure 21 ) sets the identification number to sy n- chronize communication between the wireless WAV - PK and the AXR - WAVES ...

  • AMX none - page 24

    20 Pre - Installation WAVE 2 - Way Wireless Accessories and Adapters for Touch Panels WAV - PKM Group ID DIP switch The 4 - position Group ID DIP switch ( Figure 22 ) sets the group identification nu m ber to synchronize communication between the wireless WAV - PKM and the AXR - WAVES (or WAV - LNK). Each AXR - WAVES (or WAV - LNK) must have a uniq ...

  • AMX none - page 25

    WAVE 2 - Way Wireless Accessories and Adapters for Touch Panel s Pre - Installation 21 Fully charged WAV - BP and WAV - BPM lead - acid batteries provide approximately 2 - hours of continuous touch panel operation running at full LCD brightness. Ho w- ever, you can use the touch panel's sleep mode and LCD timeout features to signif i- cantly i ...

  • AMX none - page 26

    22 Pre - Installation WAVE 2 - Way Wireless Accessories and Adapters for Touch Panels ...

  • AMX none - page 27

    WAVE 2 - Way Wireless Accessories and Adapters for Touch Panels Installation 23 Installation Overview The AXR - WAVES can be install ed on any flat surface. The following describes how to set up and install an AXR - WAVES communications system. Installing the Control System Install the control system, AXR - WAVES, WAV - PK, and WAV - PKM as follows ...

  • AMX none - page 28

    24 Installation WAVE 2 - Way Wireless Accessories and Adapters for Touch Panels 1. Mount the Central Controller in the position where it will be used. Connect the power supply. 2. Place the AXR - WAVES in the position where it will be used. The RF antenna should be set in a vertical position to communicate with the touch panels. 3. Position the tou ...

  • AMX none - page 29

    WAVE 2 - Way Wireless Accessories and Adapters for Touch Panels Installation 25 Wiring guidelines Wire size Maximum wiring length 18 AWG 1,174 f eet 20 AWG 742 feet 22 AWG 463 feet 24 AWG 292 feet Do not install the AXR - WAVES farther away from the control system than reco m- mended in Figure 26 . Preparing captive wires You will need a wire strip ...

  • AMX none - page 30

    26 Installation WAVE 2 - Way Wireless Accessories and Adapters for Touch Panels Installing the WAV - PK The WAV - PK is installed in a full - sized touch panel as described in the following steps. The WAV - PK snaps into place and is self - retaining ( Figure 28 ). 1. Fully open the rear connector cover on the full - sized tilt screen touch panel. ...

  • AMX none - page 31

    WAVE 2 - Way Wireless Accessories and Adapters for Touch Panels Installation 27 WAV - PK Batt ery Replacement Replace the WAV - PK battery ( Figure 29 ) as follows. Battery Battery clip Wake - up button Battery cover Power supply connector ON Battery cover release tab Battery compartment 1. Remove the battery cover by pressing outward on each of th ...

  • AMX none - page 32

    28 Installation WAVE 2 - Way Wireless Accessories and Adapters for Touch Panels Installing the WAV - PKM The WAV - PKM is secured with two screws once it is mounted to a Mini - TiltScreen touch pan el ( Figure 30 ). Refer to the Black/White Mini - Touch Panels (Firmware ve r- sion G3 or higher) instruction manual for more information on Mini - Tilt ...

  • AMX none - page 33

    WAVE 2 - Way Wireless Accessories and Adapters for Touch Panels Installation 29 3. Insert the WAV - PKM connector cable into the connector on the rear of the mini - touch panel. 4. Position the WAV - PKM onto th e rear of the control panel, aligning the WAV - PKMs screw holes with the mini - touch panel's screw holes. Then, using a Phillips sc ...

  • AMX none - page 34

    30 Installation WAVE 2 - Way Wireless Accessories and Adapters for Touch Panels 1. Depress the catch release point on the WAV - PKM top cover where it joi ns the mini - touch panel ( Figure 32 ). 2. While pressing downward, slide the top cover rearward and lift upward from the unit. 3. Lift the battery from the battery tray ( Figure 33 ), gr asp th ...

  • AMX none - page 35

    WAVE 2 - Way Wireless Accessories and Adapters for Touch Panels Installation 31 Installing the WAV - PM WAV - PM W aveLink Power Modules can be used singly or daisy chained for oper a- tion with a touch panel. A WAV - PM can be configured for two different har d ware configurations, as described in the following paragraphs. Single WAV - PM module W ...

  • AMX none - page 36

    32 Installation WAVE 2 - Way Wireless Accessories and Adapters for Touch Panels Multiple WAV - PM modules If you are using multiple WAV - PM modules, connect them as shown in Figure 35 . WAV - P M WAV - PM WAV - PM Figure 35 Multiple WAV - PM modules Note When using multiple WAV - PM modules, each WAV - PM must have its own power supply (PS4.2) plu ...

  • AMX none - page 37

    WAVE 2 - Way Wireless Accessories and Adapters for Touch Panels Firmware Upgrades 33 Firmware Upgrades Overview Firmware upgrades allow you to install the latest available operating system for your AXR - WAVES or Wave Packs. This section provides the information required for r e moving an old firm ware integrated circuit (ICs) and installing a new ...

  • AMX none - page 38

    34 Firmware Upgrades WAVE 2 - W ay Wireless Accessories and Adapters for Touch Panels 3. Remove the cover by lifting up while tilting the rear of the cover forward at the same time. 4. Using a non - conduc ting flat blade tool, pry the firmware chip from its socket by placing the non - conducting tool between the firmware chip and its moun t ing so ...

  • AMX none - page 39

    WAVE 2 - Way Wireless Accessories and Adapters for Touch Panels Firmware Upgrades 35 8. After removing the old firmware chip, position the new firmware chip on the socket strips with the alignment notch over the top of the notch indicator on the circuit board trace. 9. After positioning the firmware chip in the socket strips, apply sufficient dow n ...

  • AMX none - page 40

    36 Firmware Upgrades WAVE 2 - W ay Wireless Accessories and Adapters for Touch Panels WAV - PKM Battery Pack Perform the following steps to replace the WAV - PKM firmware IC. 1. Remove the WAV - PKM from the touch panel and turn it upside down. Then, u s ing a Phillips - head screwdriver, remove the two screws holding the bottom cove r to the unit ...

  • AMX none - page 41

    WAVE 2 - Way Wireless Accessories and Adapters for Touch Panels Firmware Upgrades 37 3. After the bottom cover has been removed, lift the circuit board from the unit hous ing, then turn the circuit board over and place it on a flat surface with the component side up. 4. Using a small, flat, non - conducting tool, pry the firmware IC from the IC soc ...

  • AMX none - page 42

    38 Firmware Upgrades WAVE 2 - W ay Wireless Accessories and Adapters for Touch Panels ...

  • AMX none - page 43

    WAVE 2 - Way W ireless Accessories and Adapters for Touch Panels Specifications 39 Specifications AXR - WAVES Figure 39 shows the AXR - WAVES. The specifications are in Figure 40 . AXR - WAVES specifications Power requirement Power consumption Operating frequency Indicators Connect or Enclosure Weight Dimensions 12 VDC 100 mA 2.4 GHz (digital sprea ...

  • AMX none - page 44

    40 Specifications WAVE 2 - Way Wireless Accessories and Adapters for Touch Panels WAV - PK Figure 41 shows the WAV - PK. The specifications are in Figure 42 . WAV - PK specifications Power requirement Operating frequency Connector Enclosure Battery Weight Dimension s 12 VDC 2.4 GHz (digital spread spectrum) 4 - pin Molded black matte plastic Lead - ...

  • AMX none - page 45

    WAVE 2 - Way W ireless Accessories and Adapters for Touch Panels Specifications 41 WAV - PKM Figure 43 shows the WAV - PKM. The specifications are in Figure 44 . WAV - PKM specifications Power requirement Operating frequency Connector Enclosure Battery Weight Dimensions 12 VDC 2.4 GHz (digital spread spectrum) 4 - pin Molded black matte plastic Lea ...

  • AMX none - page 46

    42 Specifications WAVE 2 - Way Wireless Accessories and Adapters for Touch Panels WAV - BP and WAV - BPM Batteries Figure 45 shows the WAV - BP and WAV - BPM batteries. Figure 46 shows the specif i- cations. WAV - BP WAV - BPM WAV - BP and WAV - BPM specifications Battery voltage Type Amp hour (Ah): WAV - WP WAV - BPM Weight: WAV - BP WAV - BPM Dim ...

  • AMX none - page 47

    WAVE 2 - Way W ireless Accessories and Adapters for Touch Panels Specifications 43 WAV - LNK WaveLink Figure 47 shows the WAV - LNK transceiver and Figure 48 shows the specific a tions. WAV - LNK specifications Power requirements Power consumption R F Frequency Enclosure Connector Enclosure Weight Dimensions 12 VDC 100 mA 2.4 GHz digital spread spe ...

  • AMX none - page 48

    44 Specifications WAVE 2 - Way Wireless Accessories and Adapters for Touch Panels WAV - PM Power Module Figure 49 Shows the WAV - PM Power Module and Figure 50 shows the specific a- tions. WAV - PM specifications Output voltage Output current Input voltage Recommended power su p ply Weight Dimensions Enclosure Connectors Options 12 VDC 3.0 AMP maxi ...

  • AMX none - page 49

    WAVE 2 - Way Wireless Accessories and Adapters for Touch Panels Contacting Sales and Technical Support 45 Contacting Sales and Technical Support Overview Customer service and satisfaction is our highest priority here at Panja Incorp o rated. If you are experiencing any problems or have a question about your product, please contact Technical Support ...

  • AMX none - page 50

    46 Specifications WAVE 2 - Way Wireless Accessories and Adapters for Touch Panels Other Panja contacts Telephone Fax E - mail Special Projects 800 - 452 - 6945 972 - 907 - 6200 Special_projects@panja.com Synergy 800 - 952 - 6995 972 - 644 - 1291 Synergy@panja.com International Team +1 972 - 907 - 6247 or +1 800 - 222 - 0193 +1 972 - 907 - 6213 Inte ...

  • AMX none - page 51

    WAVE 2 - Way Wireless Accessories and Adapters for Touch Panels Contacting Sales and Technical Support 47 • If you are having a problem with hardware  identify the equi p ment/ firmware version you are using, what you were doing when the problem o c curred, and any troubleshooting you've tried (if any). • If your problem is with a softw ...

  • AMX none - page 52

    042 - 004 - 2307 03/00 ©2000 Panja Inc. All rights re served. The Panja logo is a registered trademark of Panja, Incorporated. All other trademarks contained in this document are the properties of their respe c- tive owners. Panja, Incorporated reserves the right to alter specifications without notice at any tim e. 11995 Forestgate Drive 972/644 - ...

メーカー AMX カテゴリー Network Card

AMX noneのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- noneの取扱説明書
- AMXの製品カード
- パンフレット
- またはAMX noneの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、AMX noneの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、AMX noneの取り付け説明書、サービスマニュアル、簡易説明書、またはAMX noneのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、AMX noneの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

AMX noneデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがAMX noneを使用するのを助ける技術的文書のことです。説明書は通常、全てのAMX noneユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

AMXの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. AMX noneの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははAMX noneの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。AMX noneに関してこのドキュメントで見つけることができる全てのヒントの目次
3. AMX noneデバイスの基本機能を使うにあたってのヒント。 AMX noneのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。AMX noneに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるAMX noneのメーカー/サービスへの連絡先に関する情報。

AMX noneについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもAMX noneの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがAMX noneで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)