日本語 dropdown-ico

Ryobi PNC3840-RY74005d, PCN4545-RY74007Dの取扱説明書

20ページ 1.32 mb
ダウンロード

ページに移動 of 20

Summary
  • Ryobi PNC3840-RY74005d, PCN4545-RY74007D - page 1

    OPERA T OR’S MANU AL PCN3840 - R Y74005D - 406 mm (16 in.) 38cc Chainsaw PCN4545 - R Y74007D - 457 mm (18 in.) 45cc Chainsaw Y our new chainsa w has been engineered and manuf actured to Ryobi’ s high standard f or dependability , ease of operation, and operator saf ety . Properly cared for , it will give y ou years of rugged, trouble-free perf ...

  • Ryobi PNC3840-RY74005d, PCN4545-RY74007D - page 2

    2 UK ■ ■ ■ ■ ■ Introduction .......................................................................................................................................................................................... 2 ■ ■ ■ ■ ■ General Safety Rules .................................................................................. ...

  • Ryobi PNC3840-RY74005d, PCN4545-RY74007D - page 3

    3 UK W ARNING: The warnings, labels, and instructions found in this section of the operator’s manual are for your safety. Failure to follow all instructions may result in serious personal injury. Safe operation of this tool requires that you read and understand this operator’s manual and all labels affixed to the tool. Safety is a combination o ...

  • Ryobi PNC3840-RY74005d, PCN4545-RY74007D - page 4

    4 UK ■ KEEP ALL P ARTS OF Y OUR BOD Y a wa y from the saw chain when the engine is running. ■ ■ ■ ■ ■ AL W A YS CARR Y THE CHAINSA W WITH THE ENGINE ST OPPED AND THE BRAKE ENGA GED, the guide bar and saw chain to the rear , and the silencer awa y from your body . When transpor ting the chainsaw , use the appropriate guide bar scabbard. ...

  • Ryobi PNC3840-RY74005d, PCN4545-RY74007D - page 5

    5 UK PROPER CLOTHING FOR SAFETY ■ ■ ■ ■ ■ Wear close-fitting clothing. Always wear heavy, long trousers, boots, and gloves. Do not wear jewellery, shorts, sandals, or go barefoot. Do not wear loose-fitting clothing, which could be drawn into the engine or catch the chain or undergrowth. Wear overalls, jeans, or leggings made of cut-resist ...

  • Ryobi PNC3840-RY74005d, PCN4545-RY74007D - page 6

    6 UK Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and more safely. SYMBOL NAME EXPLANATION Indicates danger, warning or caution. It means attention!!! Your safety is involved. Your manual contains special ...

  • Ryobi PNC3840-RY74005d, PCN4545-RY74007D - page 7

    7 UK Petrol Use unleaded petrol intended for motor vehicle use with an octane rating of 87 ([R + M] / 2) or higher. Oil Use 2-cycle oil for air cooled engines. Mix Petrol and Oil Mix the fuel mix thoroughly and also each time before refuelling. SA VE THESE INSTR UCTIONS SYMBOLS SPECIFICA TIONS Weight - No bar, chain, fuel or oil ................... ...

  • Ryobi PNC3840-RY74005d, PCN4545-RY74007D - page 8

    8 UK F or your saf ety , study this entire manual bef ore operating the saw . P a y par ticular attention to the precautions and instructions listed in the operator’ s manual. W ARNING: The warnings and instructions in this section of the operator’s manual are for your safety and to prevent serious personal injury. UNDERSTANDING YOUR CHAINSAW S ...

  • Ryobi PNC3840-RY74005d, PCN4545-RY74007D - page 9

    9 UK KICK-BACK PRECAUTIONS See Figures 4 and 5. Rotational kick-back ( A ) occurs when the moving chain contacts an object at the Kick-bac k Danger Zone ( B ) of the guide bar . The result is a lightning-fast, reverse reaction which kicks the guide bar up and back to wards the operator . This reaction ma y cause loss of control which can result in ...

  • Ryobi PNC3840-RY74005d, PCN4545-RY74007D - page 10

    10 UK NOTE: Do not use dirty, used or otherwise contaminated oils. Damage may occur to the oil pump, bar, or chain. 1. Carefully pour the bar and chain oil into the tank. 2. Fill the oil tank every time you fuel the engine. STARTING THE ENGINE See Figure 8. W ARNING: Keep your body to the left of the chain line. Never straddle the saw or chain, or ...

  • Ryobi PNC3840-RY74005d, PCN4545-RY74007D - page 11

    11 UK ■ ■ ■ ■ ■ Maintain a proper grip on the saw whenever the engine is running. The fingers should encircle the handle and the thumb be wrapped under the handlebar . This gr ip is least likely to be broken (by a kick-back or other sudden reaction of the saw). Any grip in which the thumb and fingers are on the same side of the handle is ...

  • Ryobi PNC3840-RY74005d, PCN4545-RY74007D - page 12

    12 UK ADJUSTING IDLING SPEED See Figure 24. ■ ■ ■ ■ ■ If the engine starts, runs, and accelerates but will not idle, turn the idling speed screw “ T ” clockwise to increase idling speed. ■ ■ ■ ■ ■ If the chain turns at idle, turn the idling speed screw “ T ” anticlockwise to reduce the idle RPM and stop the chain movemen ...

  • Ryobi PNC3840-RY74005d, PCN4545-RY74007D - page 13

    On large diameter trees, stop the back cut before it is deep enough for the tree to either fall or settle back on the stump. Then insert soft wooden or plastic wedges ( F ) into the cut so they do not touch the chain. Drive wedges in, little by little, to help jack the tree over. When bucking or felling with a wedge, it may be necessary to remove t ...

  • Ryobi PNC3840-RY74005d, PCN4545-RY74007D - page 14

    14 UK CUTTING SPRING POLES See Figure 37. A spring pole ( A ) is any log, branch, rooted stump, or sapling which is bent under tension by other wood so that it springs back if the wood holding it is cut or removed. On a fallen tree, a rooted stump has a high potential of springing back to the upright position during the bucking cut to separate the ...

  • Ryobi PNC3840-RY74005d, PCN4545-RY74007D - page 15

    15 UK CHAIN MAINTENANCE See Figures 51 and 52. CA UTION: Check that the switch is in the STOP “ ” position before you w ork on the saw . Use only a low-kic k-back chain on this sa w . This fast-cutting chain provides kick-back reduction when properly maintained. F or smooth and fast cutting, maintain the chain properly . The chain requires shar ...

  • Ryobi PNC3840-RY74005d, PCN4545-RY74007D - page 16

    16 UK MAINTAINING DEPTH GAUGE CLEARANCE See Figures 51, 59, and 60. ■ Maintain the depth gauge ( A ) at a clearance of 0.6 mm (0.025”). Use a depth gauge tool for checking the depth gauge clearances. ■ Every time the chain is filed, check the depth gauge clearance. ■ Use a flat file ( B ) (not provided) and a depth gauge jointer ( C ) (not ...

  • Ryobi PNC3840-RY74005d, PCN4545-RY74007D - page 17

    17 UK Choose one of the following cleaning options: 9. T o lightly clean, tap the filter against a smooth, flat surf ace to dislodge most saw dust and dirt particles. 10. For a more thorough cleaning, clean in w ar m soap y water , rinse, and let dr y completely . NOTE: An alternative method is to clean the filter with compressed air (always wear e ...

  • Ryobi PNC3840-RY74005d, PCN4545-RY74007D - page 18

    18 UK RECOMMENDED BAR AND CHAIN COMBINATIONS FOR .325 LOW PROFILE .050 GAUGE Length of Bar Guide Bar Part Number Chain Part Number 406 mm (16 in.) 984316001 PS06136 457 mm (18 in.) 984319001 PS06135 PROBLEM POSSIBLE CA USE SOLUTION Engine will not start. (Make sure ignition switch is in start position “I”.) Engine starts but will not accelerate ...

  • Ryobi PNC3840-RY74005d, PCN4545-RY74007D - page 19

    19 UK PROBLEM POSSIBLE CA USE SOLUTION Engine starts, runs, and accelerates but will not idle. Engine starts and runs, but chain is not rotating. Bar and chain running hot and smoking. Carburettor requires adjustment. 1. Chain oil tank empty. 2. Check chain tension for overtight condition. 3. Check for oiler function. 1. Chain brake engaged. 2. Cha ...

  • Ryobi PNC3840-RY74005d, PCN4545-RY74007D - page 20

    20 UK SAFETY DIRECTIVE EC DECLARATION OF CONFORMITY According to machiner y directiv e 98/37/EC and EMC directive 89/336/EEC - We , Ryobi T echnologies Inc., 1428 P ear man Dair y Road, Anderson, SC 29625 Declare in sole responsibility that the product: PCN3840 (R Y74005D) and PCN45 45 (R Y74007D) - to which this cer tificate applies, conforms to t ...

メーカー Ryobi カテゴリー Chainsaw

Ryobi PNC3840-RY74005d, PCN4545-RY74007Dのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- PNC3840-RY74005d, PCN4545-RY74007Dの取扱説明書
- Ryobiの製品カード
- パンフレット
- またはRyobi PNC3840-RY74005d, PCN4545-RY74007Dの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Ryobi PNC3840-RY74005d, PCN4545-RY74007Dの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Ryobi PNC3840-RY74005d, PCN4545-RY74007Dの取り付け説明書、サービスマニュアル、簡易説明書、またはRyobi PNC3840-RY74005d, PCN4545-RY74007Dのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Ryobi PNC3840-RY74005d, PCN4545-RY74007Dの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Ryobi PNC3840-RY74005d, PCN4545-RY74007Dデバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがRyobi PNC3840-RY74005d, PCN4545-RY74007Dを使用するのを助ける技術的文書のことです。説明書は通常、全てのRyobi PNC3840-RY74005d, PCN4545-RY74007Dユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Ryobiの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Ryobi PNC3840-RY74005d, PCN4545-RY74007Dの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははRyobi PNC3840-RY74005d, PCN4545-RY74007Dの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Ryobi PNC3840-RY74005d, PCN4545-RY74007Dに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Ryobi PNC3840-RY74005d, PCN4545-RY74007Dデバイスの基本機能を使うにあたってのヒント。 Ryobi PNC3840-RY74005d, PCN4545-RY74007Dのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Ryobi PNC3840-RY74005d, PCN4545-RY74007Dに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるRyobi PNC3840-RY74005d, PCN4545-RY74007Dのメーカー/サービスへの連絡先に関する情報。

Ryobi PNC3840-RY74005d, PCN4545-RY74007Dについてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもRyobi PNC3840-RY74005d, PCN4545-RY74007Dの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがRyobi PNC3840-RY74005d, PCN4545-RY74007Dで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)