Honeywell DN 10DYの取扱説明書

24ページ 0.28 mb
ダウンロード

ページに移動 of 24

Summary
  • Honeywell DN 10DY - page 1

    1 INSTRUCTION MANUAL AND SAFETY INSTRUCTIONS FOR CORDLESS ANGLE DRILL MODEL DN 10DY Variable speed WARNING: Improper and unsafe use of this power tool can result in death or serious bodily injury! This manual contains important information about product safety. Please read and understand this manual before operating the power tool. Please keep this ...

  • Honeywell DN 10DY - page 2

    2 — CONTENTS — Page IMPORTANT INFORMATION .................................................................................... 3 MEANINGS OF SIGNAL WORDS ............................................................................. 3 SAFETY IMPORTANT SAFETY INSTRUCTIONS FOR USING ALL POWER TOOLS ................................................. ...

  • Honeywell DN 10DY - page 3

    3 IMPORTANT INFORMATION Read and understand all of the operating instructions, safety precautions and warnings in the Instruction Manual before operating or maintaining this power tool. Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic safety rules or precautions. An accident can often b ...

  • Honeywell DN 10DY - page 4

    4 SAFETY IMPORTANT SAFETY INSTRUCTIONS FOR USING ALL POWER TOOLS WARNING: Death or serious bodily injury could result from improper or unsafe use of power tools. To avoid these risks, follow these basic safety instruc- tions: READ ALL INSTRUCTIONS 1. NEVER TOUCH MOVING PARTS. Never place your hands, fingers or other body parts near the tool ’ s m ...

  • Honeywell DN 10DY - page 5

    5 8. KEEP CHILDREN AWAY. Do not let visitors contact tool. All visitors should be kept safely away from work area. 9. DON ’ T FORCE TOOL. It will do the job better and safer at the rate for which it was intended. 10. USE RIGHT TOOL. Don ’ t force small tool or attachment to do the job of a heavy-duty tool. Don ’ t use tool for purpose not int ...

  • Honeywell DN 10DY - page 6

    6 20. HANDLE TOOL CORRECTLY. Operate the tool according to the instructions provided herein. Do not drop or throw the tool. Never allow the tool to be operated by children, individuals unfamiliar with its operation or unauthorized personnel. 21. CHECK FOR LIVE WIRES. Avoid the risk of severe electrical shock by checking for live electrical wires th ...

  • Honeywell DN 10DY - page 7

    7 IMPORTANT SAFETY INSTRUCTIONS FOR USE OF THE CORDLESS ANGLE DRILL WARNING: Death or serious bodily injury could result from improper or unsafe use of the cordless angle drill. To avoid these risks, follow these basic safety instructions: 1. Never place hands or other body parts near the drill bit or chuck during operation. Hold the drill by its h ...

  • Honeywell DN 10DY - page 8

    8 Table 1 RECOMMENDED MINIMUM AWG SIZE FOR EXTENSION CORDS FOR BATTERY CHARGERS AC Input Rating Amperes* AWG Size of Cord Equal to or but less Length of Cord, Feet (Meter) greater than than 25 (7.5) 50 (15) 100 (30) 150 (45) 0 2 18 18 18 16 2 3 18 18 16 14 3 4 18 18 16 14 1250watts 125 volts = 10 amperes * If the input rating of a battery charger i ...

  • Honeywell DN 10DY - page 9

    9 1. NEVER disassemble the battery. 2. NEVER incinerate the battery, even if it is damaged or is completely worn out. The battery can explode in a fire. 3. NEVER short-circuit the battery. 4. NEVER insert any objects into the battery charger ’ s air vents. Electric shock or damage to the battery charger may result. 5. NEVER charge outdoors. Keep ...

  • Honeywell DN 10DY - page 10

    10 䡬 Battery (EB9, EB9B) Fig. 1 Terminal Hole Nameplate OPERA TION AND MAINTENANCE NOTE: The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance of the power tool. Some illustrations in this Instruction Manual may show details or attachments that differ from those on your own power tool ...

  • Honeywell DN 10DY - page 11

    11 MODEL UC12Y UC14YF / UC14YF2 Input power source Single phase: AC 120V 60 Hz Charging time EB12 ....... Approx. 60 min. EB12 ....... Approx. 45 min. (At a temperature of 68 ° (F20 ° C)) EB12B .... Approx. 60 min. Charging voltage DC 2.4 – 12V DC7.2 – 14.4V Charging current DC 1.3A DC 1.9A Weight 2.9 lbs. (1.3 kg) 2.9 lbs. (1.3 kg) Motor DC ...

  • Honeywell DN 10DY - page 12

    12 ACCESSORIES WARNING: Accessories for this power tool are mentioned in this Instruction Manual. The use of any other attachment or accessory can be dangerous and could cause injury or mechanical damage. STANDARD ACCESSORIES OPTIONAL ACCESSORIES.....sold separately 1. Battery (EB9, EB9B) Fig. 4 DN10DY (1HCK) 1 Phillips bit (No.2) (Code No. 983006) ...

  • Honeywell DN 10DY - page 13

    13 2. Phillips bit Use ..... Driving of wood screws and tapping screws with the head of a plus groove Size .... No. 1, No. 2, No. 3 3. Slotted bit Use ..... Driving of wood screws with the head of a minus groove Size .... 1/8" (3mm), 5/32" (4mm), 1/4" (6.35mm) 4. Iron-working drill bit Use ..... Drilling various metals and lumber, ma ...

  • Honeywell DN 10DY - page 14

    14 REMOVAL AND INSTALLATION METHOD OF BATTERY 䡬 How to remove the battery. Hold the handle tight. Press the latch located at the front of the battery and pull out the battery. (Fig. 9) 䡬 How to install the battery. Position the battery so that the latch faces toward the switch trigger in the handle and insert the battery. (Fig. 9) CHARGING METH ...

  • Honeywell DN 10DY - page 15

    15 3. Charging 䡬 When the battery is connected to the battery charger, charging will commence and the pilot lamp will light in red. (See Table 2) NOTE: If the pilot lamp does not light, pull out the plug from the receptacle and check if the battery is properly mounted. 䡬 When the battery is fully charged, the pilot lamp will blink in red slowly ...

  • Honeywell DN 10DY - page 16

    16 (3) Regarding recharging time (At 68 ° F (20 ° C)) Depending on the combination of the charger and batteries, the charging time will become as shown in Table 4. NOTE: The charging time may vary according to temperature and power source voltage. 4. Disconnect battery charger from the receptacle. CAUTION: Do not pull the plug out of the receptac ...

  • Honeywell DN 10DY - page 17

    17 How to make the batteries perform longer. (1) Recharge the batteries before they become completely exhausted. When you feel that the power of the tool becomes weaker, stop using the tool and recharge its battery. If you continue to use the tool and exhaust the electric current, the battery may be damaged and its life will become shorter. (2) Avo ...

  • Honeywell DN 10DY - page 18

    18 3. Check the direction of rotation. The bit rotates clockwise (viewed from the rear side) by pushing the R-side of the selector button. The L-side of the selector button is pushed to turn the bit counterclockwise. (See Fig. 12) (The and marks are provided on the body.) 4. Switch operation 䡬 When the switch trigger is pulled, the bit ro- tates. ...

  • Honeywell DN 10DY - page 19

    19 MAINTENANCE AND INSPECTION CAUTION: Pull out battery before doing any inspection or maintenance. 1. Checking the condition of the bit. The bits should be checked regularly. If worn or broken bits can slip or decrease the efficiency of the motor and burn it out. Replace worn bits with new ones. CAUTION: If you use a driver bit of which point is w ...

  • Honeywell DN 10DY - page 20

    20 ...

  • Honeywell DN 10DY - page 21

    21 Item Part Name No. 1 Metal 2 Spindle 3A Drill Chuck 10TLRD-N 4 Flat Hd. Screw (Left Hand) M5 × 17 5 Bind Screw M3 × 7 6 Fin 7 Second Pinion 8 Motor 9 Internal Wire (A) 10 Internal Wire (A) 11 Housing (A) • (B) Set 12 Tapping Screw (W/Washer) M3 × 16 13 Name Plate 14 Terminal (B) 15 Terminal Support 16 Terminal (B) 17 Battery EB9 18 DC-Speed ...

  • Honeywell DN 10DY - page 22

    22 ...

  • Honeywell DN 10DY - page 23

    23 ...

  • Honeywell DN 10DY - page 24

    24 205 Code No. C99058363 Printed in Ireland Please contact HITACHI KOKI U.S.A. LTD. at 1-800-59-TOOLS (toll free), or HITACHI AUTHORIZED POWER TOOL SERVICE CENTER regarding COLLEC- TION. Issued by Shinagawa Intercity T ower A, 15-1, Konan 2-chome, Minato-ku, T okyo 108-6020, Japan Distributed by 3950 Steve Reynolds Blvd. Norcross, GA 30093 Hitachi ...

メーカー Honeywell カテゴリー Cordless Drill

Honeywell DN 10DYのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- DN 10DYの取扱説明書
- Honeywellの製品カード
- パンフレット
- またはHoneywell DN 10DYの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Honeywell DN 10DYの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Honeywell DN 10DYの取り付け説明書、サービスマニュアル、簡易説明書、またはHoneywell DN 10DYのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Honeywell DN 10DYの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Honeywell DN 10DYデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがHoneywell DN 10DYを使用するのを助ける技術的文書のことです。説明書は通常、全てのHoneywell DN 10DYユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Honeywellの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Honeywell DN 10DYの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははHoneywell DN 10DYの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Honeywell DN 10DYに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Honeywell DN 10DYデバイスの基本機能を使うにあたってのヒント。 Honeywell DN 10DYのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Honeywell DN 10DYに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるHoneywell DN 10DYのメーカー/サービスへの連絡先に関する情報。

Honeywell DN 10DYについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもHoneywell DN 10DYの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHoneywell DN 10DYで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)