CDA FW951の取扱説明書

31ページ 関係なし
ダウンロード

ページに移動 of 31

Summary
  • CDA FW951 - page 1

    Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer .care@cda.eu W : www .cda.eu fw951 Integrated Frost Free Fridge Freezer Manual for Installation, Use and Maintenance ...

  • CDA FW951 - page 2

    2 Important The CD A Group L td cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CD A reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance. This appliance is not designed to be used by people (in ...

  • CDA FW951 - page 3

    3 compliance with safety requirements of EEC Directive 2006/95/EEC (L ow voltage) and requirements of EMC Directive 2004/108/EEC. This appliance has been manufactured to the strictest standards and complies with all applicable legislation, including Electrical safety (L VD) and Electromagnetic interference compatibility (EMC). Parts intended to com ...

  • CDA FW951 - page 4

    4 Important Never store inflammable or explosive items and strong corrosive acids or alkalis in the appliance. This is a household appliance, which is produced in accordance with the national standard. It is intended for food storage only , not for storage of blood, medicine and biological products. T o prevent risk of fire, keep the appliance aw ...

  • CDA FW951 - page 5

    5 Before First Use Y ou must allow the fridge to settle for at least twenty four hours prior to switching the power on. It is recommended that you clean the interior of the appliance prior to first use, using a solution of bicarbonate of soda and warm water and then thoroughly drying the interior . The fridge may have an odour to it at first use. ...

  • CDA FW951 - page 6

    6 Use Fridge • Never put liquids in the refrigerator uncovered. • Never put hot foods in the refrigerator . W arm food should be allowed to cool to room temperature before being put into the refrigerator . • Nothing should rest against the rear wall of the refrigerator , as this will cause frost and possible condensation problems which will b ...

  • CDA FW951 - page 7

    7 • Follow the instructions on the food packaging for storage of frozen food. If no information is provided, foods should not be stored for more than three months after the purchase date. • Store food in small packages (ideally less than 2.5k g). This reduces the freezing time and improves the quality of the food after thawing. • W rap food b ...

  • CDA FW951 - page 8

    8 S torage The fridge section is for short term food storage. Although the temperature can be maintained between 0-10˚C, extended periods of food storage is not recommended. As the cold air circulates within the fridge, the temperature can vary between the dierent sections. As such, foods should be stored in dierent sections according to typ ...

  • CDA FW951 - page 9

    9 T o move the shelf , lift up the front section and then pull it outwards. T o replace, slide the shelf back into the slot, and the lower the front section. The salad crisper is designed with a humidity control to ensure fruit and vegetables last longer . This can be adjusted by the slider at the front right of the salad crisper . Fully opening th ...

  • CDA FW951 - page 10

    10 Control P anel A. Power button T o put the fridge freezer on standby press and hold the power button for appro ximately three seconds. The power light will flash. T o start the compressor working again, press and hold the standby button for appro ximately three seconds until the power light stays lit. B. Fridge thermostat dial The fridge temper ...

  • CDA FW951 - page 11

    11 C. Freezer thermostat dial The freezer temperature is regulated by this dial. The thermostat can be set between fully anticlockwise (super freeze function) and fully clockwise (high - warmest setting). The super freeze function can be used to freeze large quantities of fresh food as quickly as possible. T o switch on the super freeze function, t ...

  • CDA FW951 - page 12

    12 Care and Cleaning Always disconnect the appliance from the power supply before any cleaning or maintenance . Both fridge and freezer are frost free and as such this appliance is designed not to require defrosting. The fridge and freezer sections should be cleaned using a solution of bicarbonate of soda and lukewarm water . Do not use abrasive pr ...

  • CDA FW951 - page 13

    13 Defrosting the Fridge The fridge is cooled by convection using cold air forced through channels at the rear of the fridge. No defrosting is required. Defrosting the Freezer The freezer is frost free and as such is designed not to require defrosting. T o switch o the compressor for a short period of time and so to force a defrost cycle, push a ...

  • CDA FW951 - page 14

    14 T roubleshooting If you have any problems with your appliance, you should check the troubleshooting prior to calling CD A Customer Care to prevent unnecessary service calls and potential cost. If the appliance is not working • Check there is power to the appliance. • The power button on the control panel is switched on. • The house fuses a ...

  • CDA FW951 - page 15

    15 • The cooling gas in the refrigerator will make a slight bubbling noise, even when the compressor is not running. Please note: The LED lighting cannot be replaced without a service call. If the light fails, contact CD A Customer Care. Installation This appliance must never be installed close to heat sources, e.g. heating elements, cookers or i ...

  • CDA FW951 - page 16

    16 V entilation The main consideration when installing any refrigeration unit into a fitted kitchen is ventilation. The heat removed from the cooling compartment needs to be dissipated into the atmosphere. Incorrect ventilation can lead to premature compressor failure, ex cessive power consumption and total system failure. For products intended to ...

  • CDA FW951 - page 17

    17 Important Please follow the instructions to install this unit. The open channel at the rear is clearly shown. For the correct operation of the appliance it is important that the top of the housing unit is not blocked o . A channel depth of 40-50mm is normal with most units. A hole is shown in the base shelf of the unit; this allows air to be ...

  • CDA FW951 - page 18

    18 Fitting the Product Into the Cabinet 1. R emove the gasket protection pieces: The gasket protectors prevent ex cessive seal compression during transport and are required during the installation process. R emove the gasket protector from each door (fig 6) and proceed with the installation. Cover caps are provided to fill the hole; take care whe ...

  • CDA FW951 - page 19

    19 top edge of the product (fig. 7) (b). The trim piece should be fitted loosely at this stage to allow access to the top fixing brackets. 4. Fitting the magnetic seal strips: T wo magnetic seals are supplied to fill the gap between the cabinet and the edge of the products. These simply fit against the left and right edges. T o make it easier ...

  • CDA FW951 - page 20

    20 fig. 14 fig. 13 fig. 12 8. Fitting the bottom cabinet xing bracket: A sliding bracket is provided to secure the non-hinge side of the product to the cabinet. This is fitted to the bottom of the product using two machine screws, as shown below . A guide piece is also provided to ensure the unit is aligned when installed. Fit the bracket an ...

  • CDA FW951 - page 21

    21 At this stage ensure that the product is centrally aligned within the housing and then remove the guide pieces from the hinges. 10 . Securing the product to the housing: Secure the product to the housing at the hinge side by using two screws in each hinge. The fixing holes in each hinge as shown in figure 10 . 11. Securing the bottom xing b ...

  • CDA FW951 - page 22

    22 fig. 15 fig. 16 Fitting the Cabinet Fascia Doors First, fit the upper fascia by following the steps below . After fitting the upper fascia in the correct position, use the lower edge of the upper fascia as a guide for positioning the lower fascia (A distance between the two fascias when installed is normally between 2 and 4mm) and fit the l ...

  • CDA FW951 - page 23

    23 fig. 19 Fitting guides Under end face of fascia of appropriate length. Please take care to ensure the screws selected will not punch through the fascia door . 4. Remove the fitting guides. 5. Attach the fascia door assembly to the refrigerator (onto the height adjustment screws) and loosely fit the securing nuts. At this stage the final vert ...

  • CDA FW951 - page 24

    24 Adjusting the P osition of the Fascia Doors The position of the fascia doors can be made in all 3 ax es by following the guide shown below (figure 20). If the range of adjustment detailed below is not enough then the refrigerator is not located correctly in the cabinet and/ or the upper fascia fixing plates are incorrectly positioned. Horizont ...

  • CDA FW951 - page 25

    25 Depth Adjustment (Z): Ensure that the vertical and horizontal positions are correct before adjusting the depth. 1. L oosen the depth adjustment screw (C). 2. Move the fascia in or out, as required; this gives an adjustment of appro ximately 3mm. the lower fascia brackets are slotted to allow alignment of the fascia at the bottom. This is shown i ...

  • CDA FW951 - page 26

    26 Fitting the T rims and Cover Pieces 1. Open the door and lift out the decorative covers (marked ‘a’) in figure 20 2. R emove the position guides (d), turn them round so that the lip at the top faces outwards and insert them into the slots shown in the image (e); these will be used to line up the fascia panels before securing them in positio ...

  • CDA FW951 - page 27

    27 400 . Secure the mounting bracket to the fascia panel using the provided wood screws, ensuring that the screws will not penetrate through the fascia where there are any rebates, etc. and then remove the guides. Any small errors, as in the image above, can be adjusted for after the fascia has been mounted. 5. Hang the fascia panel on the support ...

  • CDA FW951 - page 28

    28 Electrical Information W arning! This appliance must be earthed. The mains lead of this appliance has been fitted with a BS 1363A 13 amp fused plug. T o change a fuse in this type of plug, follow the steps below: 1. R emove the fuse cover and fuse. 2. Fit replacement 13A fuse, AS T A approved to BS 1362 type, into the fuse cover . 3. R eplace f ...

  • CDA FW951 - page 29

    29 As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:- • The wire which is coloured GREEN and YELL OW must be connected to the terminal which is marked with the letter (E) or by the Earth symbol or coloured GREEN and YELL O W . ? ...

  • CDA FW951 - page 30

    30 ...

  • CDA FW951 - page 31

    31 ...

メーカー CDA カテゴリー Refrigerator

CDA FW951のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- FW951の取扱説明書
- CDAの製品カード
- パンフレット
- またはCDA FW951の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、CDA FW951の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、CDA FW951の取り付け説明書、サービスマニュアル、簡易説明書、またはCDA FW951のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、CDA FW951の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

CDA FW951デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがCDA FW951を使用するのを助ける技術的文書のことです。説明書は通常、全てのCDA FW951ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

CDAの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. CDA FW951の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははCDA FW951の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。CDA FW951に関してこのドキュメントで見つけることができる全てのヒントの目次
3. CDA FW951デバイスの基本機能を使うにあたってのヒント。 CDA FW951のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。CDA FW951に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるCDA FW951のメーカー/サービスへの連絡先に関する情報。

CDA FW951についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもCDA FW951の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがCDA FW951で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)