ページに移動 of 80
INSTRUCTION MANUAL iM505 VHF MARINE TRANSCEIVER ...
i FOREWORD Thank you for purchasing this Icom product. The IC-M505 VHF MARINE TRANSCEIVER is designed and built with Icom’s state of the art technology and craftsmanship. With proper care, this product should provide you with years of trouble- free operation. We want to take a couple of moments of your time to thank you for making the IC-M505 you ...
ii IN CASE OF EMERGENCY If your vessel requires assistance, contact other vessels and the Coast Guard by sending a Distress call on Channel 16. Or , transmit your Distress call using digital selective calling on Channel 70. INST ALLA TION NOTE The installation of this equipment should be made in such a manner as to respect the EC recommended electr ...
iii DOC CE versions of the IC-M505 which display the “CE” symbol on the serial number seal, comply with the essential requirements of the Euro- pean Radio and T elecommunication T erminal Directive 1999/5/EC. This warning symbol indicates that this equip- ment operates in non-harmonised frequency bands and/or may be subject to licensing condi- ...
iv FOREWORD …………………………………………………………… i IMPORT ANT …………………………………………………………… i EXPLICIT DEFINITIONS ……………………………………………… i IN CASE OF EMERGENCY…………………………………………… ii INST ALLA TION NOTE ………? ...
v PRECAUTIONS R W ARNING! NEVER connect the transceiver to an AC outlet. This may pose a fire hazard or result in an electric shock. NEVER connect the transceiver to a power source of more than 16 V DC or use reverse polarity . This will ruin the trans- ceiver . NEVER cut the DC power cable between the DC plug at the back of the transceiver and fus ...
1 1 OPERA TING RULES D D PRIORITIES • Read all rules and regulations pertaining to priorities and keep an up-to-date copy handy . Safety and Distress calls take priority over all others. • Y ou must monitor Channel 16 when you are not operating on another channel. • False or fraudulent distress signals are prohibited and pun- ishable by law . ...
2 P ANEL DESCRIPTION 2 ■ Front panel q DISTRESS KEY [DISTRESS] Push for 5 sec. to transmit a Distress call. (p. 23) w DSC MENU KEY [MENU] Push to toggle the DSC menu appear or disappear . (p. 15) e CLEAR KEY [CLR] Push to cancel the entered function, exit Set mode. (pgs. 9, 10, 55) r HAIL/RX SPEAKER KEY [HAIL•RX ] ➥ Push to turn the hailer mo ...
3 2 P ANEL DESCRIPTION u CHANNEL SELECT OR [CHANNEL•ENTER] ➥ Rotate to select the operating channels, Set mode set- tings, etc. (pgs. 6–8, 55) ➥ While pushing and holding [H/L] , rotate to adjust the brightness of the LCD and key backlight. (p. 10) ➥ Push to enter the input channel comment, selected item, etc. (pgs. 10, 55) ➥ Rotate to ...
4 2 P ANEL DESCRIPTION ■ Function display q RX SPEAKER INDICA TOR (p. 51) Appears during the RX Speaker mode. w POWER INDICA TOR (p. 8) ➥ “ 2 2 5 5 W W ” appears when high power is selected. ➥ “ 1 1 W W ” appears when low power is selected. e T AG CHANNEL INDICA TOR (p. 13) Appears when a T AG channel is selected. r DUPLEX INDICA TOR ...
5 2 P ANEL DESCRIPTION 2 !1 POSITION INDICA TOR ➥ Shows the GPS position data. •“ ? ? ? ? ” may blink every 2 sec. instead of position data when the GPS position data is invalid. In such a case, the last position data is held for up to 23.5 hours. •“ ? ? ? ? ” may blink every 2 sec. instead of position data 4 hours after the position ...
6 BASIC OPERA TION 3 ■ Channel selection ï ï Channel 16 Channel 16 is the distress and safety channel. It is used for establishing initial contact with a station and for emergency communications. Channel 16 is monitored during both Dual- watch and T ri-watch. While standing by , you must monitor Channel 16. ➥ Push [16•C] momentarily to sele ...
7 3 BASIC OPERA TION 3 ï ï International channels There are pre-programmed 57 international channels for the IC-M505. q Push [DIAL•DUAL/GRP] to select a regular channel. w While pushing and holding [H/L] , push [DIAL•DUAL/GRP] to change the channel group, if necessary . •“ I I N N T T ” appears when International channel is selected. e ...
8 3 BASIC OPERA TION ■ Receiving and transmitting CAUTION: T ransmitting without an antenna may dam- age the transceiver . q Push [POWER] to turn power ON. w Set the audio and squelch levels. ➥ Rotate [SQL] fully counterclockwise in advance. ➥ Rotate [VOL] to adjust the audio output level. ➥ Rotate [SQL] clockwise until the noise disappears ...
9 3 BASIC OPERA TION 3 ■ Call channel programming Y ou can program the call channel with your most often-used channels in each channel group for quick recall. q While pushing and holding [H/L] , push [DIAL•DUAL• GRP] one or more times to select the desired channel group (INT , USA, A TIS or DSC) to be programmed. w Push [16•C] for 1 sec. to ...
10 3 BASIC OPERA TION ■ Channel comments Memory channels can be labelled with a unique alphanumeric ID of up to 10 characters. Capital letters, small letters, 0 to 9, some symbols (/ . –) and space can be used. q Select the desired channel. • Cancel Dualwatch, T ri-watch or Scan in advance. w While pushing and holding [H/L] , push [16•C] to ...
11 3 BASIC OPERA TION 3 ■ Optional voice scrambler operation D D Activating the scrambler The optional voice scrambler provides private communica- tions. In order to receive or send scrambled transmissions you must first activate the scrambler function. T o activate the function, an optional scrambler unit is necessary . See pgs. 57, 62 for sett ...
12 SCAN OPERA TION 4 ■ Scan types Scanning is an efficient way to locate signals quickly over a wide frequency range. The transceiver has Priority scan and Normal scan. Set the T AG channels (scanned channel) before scanning. Clear the T AG channels which inconveniently stop scanning, such as those for digital communication use. (Refer to right ...
13 4 SCAN OPERA TION 4 ■ Setting T AG channels For more efficient scanning, add the desired channels as T AG channels or clear the T AG for unwanted channels. Channels that are not tagged will be skipped during scanning. T AG channels can be assigned to each channel group (INT , USA, A TIS or DSC) independently . q While pushing and holding [H/L ...
14 DUAL W A TCH/TRI-W A TCH 5 ■ Description Dualwatch monitors Channel 16 while you are receiving on another channel; T ri-watch monitors Channel 16 and the call channel while receiving another channel. Dualwatch/T ri- watch is convenient for monitoring Channel 16 when you are operating on another channel. ■ Operation q Select Dualwatch or T ri ...
15 6 DSC OPERA TION 5 6 ■ MMSI code programming The 9-digit MMSI (Maritime Mobile Service Identity: DSC self ID) code can be programmed at power ON. This code programming can be performed only once. q T urn power OFF . w While pushing [MENU] , turn power ON to enter MMSI code programming condition. e After the display appears, release [MENU] . r ...
16 6 DSC OPERA TION ■ MMSI code check The 9-digit MMSI (DSC self ID) code can be checked. q Push [MENU] to enter the DSC menu. w Rotate [CHANNEL] to select “ S S e e t t u u p p ,” push [CHAN- NEL • ENTER] . e Rotate [CHANNEL] to select “ M M M M S S I I C C h h e e c c k k ,” push [CHANNEL • ENTER] . r Check the 9-digit MMSI (DSC sel ...
17 6 DSC OPERA TION 6 ■ DSC address ID A total of 100 DSC address IDs can be programmed and named with up to 10 characters. D D Programming Individual ID q Push [MENU] to enter the DSC menu. w Rotate [CHANNEL] to select “ S S e e t t u u p p ,” push [CHAN- NEL • ENTER] . e Rotate [CHANNEL] to select “ A A d d d d : : I I N N D D V V I I D ...
18 6 DSC OPERA TION D D Deleting Individual ID q Push [MENU] to enter the DSC menu. w Rotate [CHANNEL] to select “ S S e e t t u u p p ,” push [CHAN- NEL • ENTER] . e Rotate [CHANNEL] to select “ D D E E L L : : I I N N D D V V I I D D ,” push [CHANNEL • ENTER] . • When no address ID is programmed, “ N N o o I I D D ” is displayed ...
19 6 DSC OPERA TION 6 D D Programming Group ID q Push [MENU] to enter the DSC menu. w Rotate [CHANNEL] to select “ S S e e t t u u p p ,” push [CHAN- NEL • ENTER] . e Rotate [CHANNEL] to select “ A A d d d d : : G G r r o o u u p p I I D D ,” push [CHANNEL • ENTER] . r Rotate [CHANNEL] to s et the group ID and ID name. • The group ID ...
20 6 DSC OPERA TION D D Deleting Group ID q Push [MENU] to enter the DSC menu. w Rotate [CHANNEL] to select “ S S e e t t u u p p ,” push [CHAN- NEL • ENTER] . e Rotate [CHANNEL] to select “ D D E E L L : : G G r r o o u u p p I I D D ,” push [CHANNEL • ENTER] . • When no address ID is programmed, “ N N o o I I D D ” is displayed. ...
21 6 DSC OPERA TION 6 ■ Position and time programming A distress call should include the ship’s position and time data. If no GPS is connected, your position and UTC (Univer- sal T ime Coordinated) time should be input manually . They are included automatically when a GPS receiver (NMEA0183 ver . 2.0 or 3.01) is connected. q Push [MENU] to ente ...
■ Position and time indication When a GPS receiver (NMEA0183 ver . 2.0 or 3.01) is con- nected, the transceiver displays the current position and time. When no GPS receiver is connected, the transceiver displays the manually entered position and time. A GPS receiver appropriate for the IC-M505 is not supplied by Icom. A GPS receiver with NMEA0183 ...
23 6 DSC OPERA TION 6 ■ Distress call A distress call should be transmitted, if in the opinion of the Master , the ship or a person is in distress and requires imme- diate assistance. NEVER USE THE DISTRESS CALL WHEN YOUR SHIP OR A PERSON IS NOT IN AN EMERGENCY . A DISTRESS CALL CAN BE USED ONL Y WHEN IMMEDIA TE HELP IS NEEDED. D D Simple call q ...
24 6 DSC OPERA TION ➥ A distress alert contains (default); • Nature of distress : Undesignated distress • Position data : GPS or manual input position data held for 23.5 hrs or until the power is turned OFF . ➥ The distress call is repeated every 3.5–4.5 min., until re- ceiving an ‘acknowledgement.’ ➥ Push [CLR] to cancel the ‘Cal ...
25 6 DSC OPERA TION 6 When a GPS receiver (NMEA0183 ver . 2.0 or 3.01) is con- nected, go to step y . Because the following steps ( r and t ; Current position/time programming) do not appear . r The position information appears. Set your position (lati- tude and longitude) data by rotating [CHANNEL] . • Push [16 • C] or [DIAL • DUAL/GRP] to m ...
26 6 DSC OPERA TION i After receiving the acknowledgment, reply using the mi- crophone. ➥ A distress alert contains (default); • Nature of distress : Selected nature of the distress • Position data : GPS or manual input position data is held for 23.5 hrs or until the power is turned OFF . ➥ The distress call is repeated every 3.5–4.5 min. ...
27 6 DSC OPERA TION 6 e Rotate [CHANNEL] to select the desired pre-programmed individual address or “ M M a a n n u u a a l l I I n n p p u u t t ,” push [CHAN- NEL • ENTER] . • The ID code for the individual call can be set in advance. (p. 17) • When “ M M a a n n u u a a l l I I n n p p u u t t ” is selected, set the 9-digit MMSI nu ...
28 6 DSC OPERA TION y Standby on Channel 70 until an acknowledgement is re- ceived. u When the acknowledgement ‘Able to comply’ is received, the specified channel (in step r ) is selected with beeps automatically . Or , when the acknowledgement ‘Unable to comply’ is received, the display returns to the operated channel (before enter the DSC ...
29 6 DSC OPERA TION 6 r Rotate [CHANNEL] to select “ A A b b l l e e t t o o C C o o m m p p l l y y ” or “ U U n n a a b b l l e e t t o o C C o o m m p p l l y y ,” push [CHANNEL • ENTER] . • When “ U U n n a a b b l l e e t t o o C C o o m m p p l l y y ” is selected, “No Reason Given” will be transmitted. t Push [CHANNEL • ...
30 6 DSC OPERA TION r Rotate [CHANNEL] to select a desired intership channel, push [CHANNEL • ENTER] . • Intership channels are already preset into the transceiver in rec- ommended order . t Push [CHANNEL • ENTER] to transmit the group call. • If Channel 70 is busy , the transceiver stands by until the channel becomes clear . y After the gr ...
31 6 DSC OPERA TION 6 D D T ransmitting an all ships call Large ships use Channel 70 as their ‘listening channel.’ When you want to announce a message to all ships within range, use the all ships call function. q Push [MENU] to enter the DSC menu. w Rotate [CHANNEL] to select “ A A l l l l S S h h i i p p s s C C a a l l l l ,” and push [CH ...
32 6 DSC OPERA TION t After the all ships call has been transmitted, the following indication is displayed. y Push [CLR] to exit and the transceiver selects Channel 16 automatically . • Even if [CLR] hasn’t been pushed, the transceiver automatically selects Channel 16 after 2 sec. of inactivity . D D T ransmitting a position request call T rans ...
33 6 DSC OPERA TION 6 r Push [CHANNEL • ENTER] to transmit the position request call. • If Channel 70 is busy , the transceiver stands by until the channel becomes clear . t After the position request call has been transmitted, the fol- lowing indication is displayed. y Push [CLR] to return to the previous indication before en- tering the DSC m ...
34 6 DSC OPERA TION D D T ransmitting a position report call T ransmit a position report call when you want to announce your own position to a specific ship and to get an answer , etc. q Push [MENU] to enter the DSC menu. w Rotate [CHANNEL] to select “ P P o o s s i i t t i i o o n n R R e e p p o o r r t t ,” push [CHANNEL • ENTER] . •“ ...
35 6 DSC OPERA TION 6 y Push [CHANNEL • ENTER] to transmit the position report call. • If Channel 70 is busy , the transceiver stands by until the channel becomes clear . u After the position report call has been transmitted, the fol- lowing indication is displayed. i Push [CLR] to return to the previous indication before en- tering the DSC men ...
36 6 DSC OPERA TION D D T ransmitting a polling request call T ransmit a polling request call when you want to know if a specific vessel is within communication range. q Push [MENU] to enter the DSC menu. w Rotate [CHANNEL] to select “ P P o o l l l l i i n n g g R R e e q q u u e e s s t t ,” push [CHANNEL • ENTER] . e Rotate [CHANNEL] to s ...
37 6 DSC OPERA TION 6 t After the polling request call has been transmitted, the fol- lowing indication is displayed. y Push [CLR] to return to the previous indication before en- tering the DSC menu. • Even if [CLR] hasn’t been pushed, the display automatically re- turns to the previous indication after 2 sec. of inactivity . D D T ransmitting ...
38 6 DSC OPERA TION When a GPS receiver (NMEA0183 ver . 2.0 or 3.01) is con- nected, go to step y . Because the following steps ( r and t ; Current position/time programming) do not appear . r The position information appears. Set your position (lati- tude and longitude) data by rotating [CHANNEL] . • Push [16 • C] or [DIAL • DUAL/GRP] to mov ...
39 6 DSC OPERA TION 6 D D T ransmitting a position report reply call T ransmit a position report reply call when a position report call is received. q Push [MENU] to enter the DSC menu. w Rotate [CHANNEL] to select “ P P O O S S R R e e p p o o r r t t R R e e p p l l y y ,” push [CHANNEL • ENTER] . •“ P P O O S S R R e e p p o o r r t t ...
40 6 DSC OPERA TION D D T ransmitting a polling request reply call T ransmit a polling reply call when a polling request call is re- ceived. q Push [MENU] to enter the DSC menu. w Rotate [CHANNEL] to select “ P P o o l l l l i i n n g g R R e e p p l l y y ,” push [CHANNEL • ENTER] . •“ P P o o l l l l i i n n g g R R e e p p l l y y ” ...
41 6 DSC OPERA TION 6 ■ Receiving DSC calls D D Receiving a distress call While monitoring Channel 70 and a distress call is received: ➥ The emergency alarm sounds for 2 minutes. • Push [CLR] to stop the alarm. ➥ “ R R e e c c e e i i v v e e d d D D i i s s t t r r e e s s s s ” appears in the display , then Channel 16 is automatically ...
42 6 DSC OPERA TION D D Receiving an individual call While monitoring Channel 70 and an individual call is re - ceived: ➥ The emergency alarm or beeps sound depending on the received category . ➥ “ R R e e c c e e i i v v e e d d I I n n d d i i v v i i d d u u a a l l ” appears in the display . ➥ Push [CLR] to stop the beep, then push [C ...
43 6 DSC OPERA TION 6 D D Receiving a geographical area call While monitoring Channel 70 and a geographical area call (for the area you are in) is received: ➥ Emergency alarm or beeps sound depending on the re- ceived category . ➥ “ R R e e c c e e i i v v e e d d G G e e o o g g r r a a p p h h i i c c ” appears in the display . ➥ Push [ ...
44 6 DSC OPERA TION D D Receiving a polling request call While monitoring Channel 70 and a polling request call is re- ceived: ➥ “ R R e e c c e e i i v v e e d d P P O O L L L L R R E E Q Q ” appears in the display . ➥ Push [CLR] to stop the beep, then push [CHANNEL • ENTER] to reply to the call; push [CLR] to ignore the call. D D Receiv ...
45 6 DSC OPERA TION 6 ■ Received messages The transceiver automatically stores up to 20 distress mes- sages and 20 other messages. The messages can be used as an assistance to the logbook. q Push [MENU] to enter the DSC menu. w Rotate [CHANNEL] to select “ R R e e c c e e i i v v e e d d C C a a l l l l s s ,” push [CHANNEL • ENTER] . D D D ...
46 6 DSC OPERA TION D D Other messages q Rotate [CHANNEL] to select “ O O t t h h e e r r ,” push [CHAN- NEL • ENTER] . w Rotate [CHANNEL] to scroll to the desired message, push [CHANNEL • ENTER] . • Messages which are blinking have not been read. e Rotate [CHANNEL] to scroll the message. • The stored message has various information, de ...
47 6 DSC OPERA TION 6 ■ DSC Set mode D D MMSI code check (See p. 16) D D Add Individual ID/Group ID (See pgs. 17, 19) D D Delete Individual ID/Group ID (See pgs. 18, 20) D D Offset time This item sets the offset time from the UTC (Universal T ime Coordinated) time. q Push [MENU] to enter the DSC menu. w Rotate [CHANNEL] to select “ S S e e t t ...
48 6 DSC OPERA TION D D Automatic acknowledgement This item sets the automatic acknowledgement function to ON or OFF . When a position request, position report or polling request call is received, the transceiver automatically transmits a position request reply , position report reply or polling reply call, re- spectively . q Push [MENU] to enter t ...
49 6 DSC OPERA TION 6 D D NMEA Output Select an NMEA Output function from OFF , All Station or List Station. When receiving position acknowledgment, the transceiver outputs it to the external equipment via the NMEA connector . q Push [MENU] to enter the DSC menu. w Rotate [CHANNEL] to select “ S S e e t t u u p p ,” push [CHAN- NEL • ENTER] . ...
50 OTHER FUNCTIONS 7 ■ Intercom operation The optional Intercom function allows you to talk to the deck from the cabin. The optional COMMANDMIC III™ is required for Intercom operation. Connect an optional command microphone as described on p. 63. • T ransmitting is impossible during Intercom operation. • The received signal is muted during ...
51 7 OTHER FUNCTIONS 7 • While in the Intercom mode, the transceiver functions (transmit and receive) are interrupted. If the transceiver is in transmit condition, the Intercom function is not avail- able. • When a DSC call is received, the intercom function is in- terrupted with an automatic return to the transceiver mode. The transceiver’s ...
52 7 OTHER FUNCTIONS ■ Hailer operation The IC-M505 has a hailer function for voice amplification over a loudspeaker , making it unnecessary to leave the bridge to talk a hailing party . Connect an external hailer speaker (25 W nominal at 13.8 V/4 Ω ) as described on p. 58. • T ransmitting is not possible during hailer operation. • The rec ...
53 7 OTHER FUNCTIONS 7 ■ Automatic foghorn function The automatic foghorn function sounds a horn repeatedly until the function is turned OFF . Four patterns are available for varying conditions. The foghorn outputs from the hailer speaker . T o use this func- tion, the hailer speaker must be connected to the transceiver . See p. 58 for connection ...
54 7 OTHER FUNCTIONS q While pushing and holding [H/L] , push [HAIL • RX ] to enter auto foghorn mode. w Rotate [CHANNEL] to select the desired foghorn pattern, push [CHANNEL • ENTER] . •‘ U U N N D D E E R R W W A A Y Y ,’ ‘ S S T T O O P P ,’ ‘ S S A A I I L L ,’ ‘ T T O O W W ’ are available. (p. 53) • Even if [CHANNEL ? ...
55 8 SET MODE 7 8 ■ Set mode programming Set mode is used to change the conditions of the transceiver’s functions: Scan type, Scan resume timer , Dual/T ri-watch, Beep tone, LCD contrast, Automatic foghorn frequency , Radio power , Scrambler type* and Scrambler code.* *Appears only when the optional scrambler unit is installed. Available functi ...
56 8 SET MODE D D Dual/T ri-watch This item can be selected as Dualwatch or T ri-watch. (p. 14) D D Beep tone Y ou can select the silent operation by turning beep tones OFF or you can have confirmation beeps sound at the push of a key by turning beep tones ON. D D LCD contrast The LCD contrast can be adjustable to 8 levels. The level 1 is the lowe ...
57 8 SET MODE 8 D D Radio power (Appears when the HM-162E is connected) This item sets the Radio Power function ON or OFF . ON : The transceiver ’s power is controlled by the optional command microphone. When the command micro- phone is turned OFF , the transceiver will also be turned OFF automatically . OF F : The transceiver ’s power is not c ...
58 CONNECTIONS AND MAINTENANCE 9 ■ Connections q NMEA IN LEAD (Red) Connects to a GPS receiver for position indication. • A NMEA0183 ver . 2.0 or 3.01 (sentence formatters RMC, GGA, GNS, GLL and VTG) compatible GPS receiver is required. Ask your dealer about suitable GPS receivers. w NMEA OUT LEAD (White) Connects to a PC or navigation equipmen ...
59 9 CONNECTIONS AND MAINTENANCE 9 CAUTION: After connecting the DC power cable, NMEA IN/OUT leads, external speaker lead and hailer/foghorn lead, cover the connector and leads with an adhesive tape as shown below , to prevent water seeping into the transceiver . ■ Antenna A key element in the performance of any communication sys- tem is the ante ...
60 9 CONNECTIONS AND MAINTENANCE ■ Mounting the transceiver D D Using the supplied mounting bracket The universal mounting bracket supplied with your transceiver allows overhead or dashboard mounting. • Mount the transceiver securely with the 4 supplied screws (5 × 20) to a surface which is more than 10 mm thick and can support more than 5 kg. ...
61 9 CONNECTIONS AND MAINTENANCE 9 ■ MB-75 installation An optional MB-75 FLUSH MOUNT KIT is available for mounting the transceiver to a flat surface such as an instru- ment panel. CAUTION: KEEP the transceiver and microphone at least 1 meter away from your vessel’s magnetic navigation com - pass. q Using the template on the last page, careful ...
62 9 CONNECTIONS AND MAINTENANCE ■ UT -1 12/UT -98 installation CAUTION: DISCONNECT the DC power cable from the transceiver before performing any work on the transceiver . Otherwise, there is danger of electric shock and/or equip- ment damage. Follow the case opening procedure shown here when you want to install an optional scrambler unit. q Remo ...
63 9 CONNECTIONS AND MAINTENANCE 9 r Return the cables and screws to the original position. • Be sure not upside down the flat cable. CAUTION: • When re-assembling the case and tightening the screws, you must keep the specified torque (0.5± 0.07 N.m). Oth- erwise the transceiver may be damaged (torque too high) or lose waterproof efficiency ...
64 9 CONNECTIONS AND MAINTENANCE q I nsert the supplied cable into the external microphone jack and tighten the cable nut as shown below . w T o use the supplied cable as a wall socket, perform the fol - lowing steps. e Using the mounting base as a template, carefully mark the holes where the cable and three screws will be fastened. r Drill holes a ...
65 9 CONNECTIONS AND MAINTENANCE 9 Gasket Mounting base Cap Nut ...
66 TROUBLESHOOTING 10 POSSIBLE CAUSE SOLUTION REF . No sound from speaker . • Squelch level is too high. • V olume level is too low . • Speaker has been exposed to water . p. 8 p. 8 — • Set [SQL] to the threshold point. • Set [VOL] to a suitable level. • Drain water from the speaker . The transceiver does not turn ON. • Bad connecti ...
67 11 SPECIFICA TIONS AND OPTIONS 10 11 ■ Speci fi cations D D General • Frequency coverage : Tx 156.000–161.450 MHz Rx 156.000–163.425 MHz • Mode : FM (16K0G3E), DSC (16K0G2B) • Channel spacing : 25 kHz • Current drain (at 13.8 V) : TX high 5.5 A max. Max. audio 1.5 A max. • Power supply requirement : 13.8 V DC (10.8 to 15.6 V) (n ...
68 11 SPECIFICA TIONS AND OPTIONS D D Dimensions ■ Options • MB-75 FLUSH MOUNT KIT For mounting the transceiver to a panel. • HM-162E COMMANDMIC III ™ External microphone-type controller . Provides optional inter- com operation. 6 m microphone cable and mount-ing base in- cluded. Black and white colors are available. Do not connect the HM-1 ...
69 12 CHANNEL LIST 11 12 • International channels CH Frequency (MHz) CH Frequency (MHz) CH Frequency (MHz) CH Frequency (MHz) CH Frequency (MHz) CH Frequency (MHz) T ransmit Receive T ransmit Receive T ransmit Receive T ransmit Receive T ransmit Receive T ransmit Receive 01 156.050 160.650 1 1 156.550 156.550 21 157.050 161.650 61 156.075 160.675 ...
70 12 CHANNEL LIST • USA channels (for U.K. version only) Frequency (MHz) Frequency (MHz) Frequency (MHz) Frequency (MHz) Frequency (MHz) Frequency (MHz) T ransmit Receive T ransmit Receive T ransmit Receive T ransmit Receive T ransmit Receive T ransmit Receive 156.050 156.050 156.600 156.600 157.100 157.100 156.225 156.225 156.775 156.775 156.82 ...
TEMPLA TE HM-162E Unit: mm 29.5 to 31.5 (d) 2 165 11 0 146 92.4 R12 (Max.) MB-75 Cut here ...
...
MEMO ...
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan A-6484H-1EU- q Printed in Japan © 2006 Icom Inc. < Intended Country of Use > GER AUT GBR IRL NOR FRA NED BEL LUX ESP POR ITA GRE SWE DEN FIN SUI ...
Icom IC-M505のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- IC-M505の取扱説明書
- Icomの製品カード
- パンフレット
- またはIcom IC-M505の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Icom IC-M505の取扱説明書に含まれています。
取扱説明書と呼ばれる文書のグループは、Icom IC-M505の取り付け説明書、サービスマニュアル、簡易説明書、またはIcom IC-M505のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Icom IC-M505の製品を使用するにあたって最も人気のある説明書を閲覧できます。
Icom IC-M505デバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがIcom IC-M505を使用するのを助ける技術的文書のことです。説明書は通常、全てのIcom IC-M505ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。
Icomの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。
1. Icom IC-M505の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははIcom IC-M505の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Icom IC-M505に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Icom IC-M505デバイスの基本機能を使うにあたってのヒント。 Icom IC-M505のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Icom IC-M505に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるIcom IC-M505のメーカー/サービスへの連絡先に関する情報。
Icom IC-M505についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもIcom IC-M505の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがIcom IC-M505で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。