Cisco Systems UBR7225VXRの取扱説明書

20ページ 0.54 mb
ダウンロード

ページに移動 of 20

Summary
  • Cisco Systems UBR7225VXR - page 1

    Q UICK S TART G UIDE Cisco uBR7225VXR Universal Broadband Router 1 Overview 2 Preparing for Installation 3 Installation Guidelines 4 Installing the Chassis 5 Connecting the Chassis to P ower 6 Cabling 7 P owering on the Cisco uBR7225VXR Router 8 T roubleshooting the In stallation 9 Rel at ed Do cu me nta ti on 10 Obtaining Documentation and Submit ...

  • Cisco Systems UBR7225VXR - page 2

    2 • Supports both 6-MHz North American channel plans using IT U-T J.83 Annex B operation and 8-MHz phase alternating line (P AL) and Sequential Coulour A vec Memoire (SECAM ) channel plans using ITU-T J.83 Annex A operation. • W orks in conjunction w ith dialup access products to support upstream traffic from DOCSIS-based cable interfaces conne ...

  • Cisco Systems UBR7225VXR - page 3

    3 Figur e 1 Fr ont View of the Chassis Figure 2 Rear View of the Chassis 1 Cable interface card slot 1 2 Cable interface car d slot 2 1 Gigabit Ethernet 0/1 5 Console port 2 Gigabit Ethernet 0/2 6 Auxiliary port 3 Gigabit Ethernet 0/3 7 AC-input power supply 2 4 Network processing engine 8 AC-input power supply 1 270489 uBR7225 -VXR US2 US4 US5 US6 ...

  • Cisco Systems UBR7225VXR - page 4

    4 Card Slot and Logica l Interface Numbering The cable interface line card slots maintain the same slot number regardless of whether other cable interface line cards are installed or removed. However , when you mo ve a line card to a different slot, the lo gical interface number cha nges to reflect t he new slot number . (See Figure 3 .) Figur e 3 ...

  • Cisco Systems UBR7225VXR - page 5

    5 Temperature and Humi dity Requirements Table 1 and Table 2 list the nomina l operating and non-operating environm ent requirements. Any measurements that approach the minimum or maximum of a range indicate a potential problem. T able 1 Oper ating En vir onment T able 2 No n-oper ating Environment Verifying Contents After Unpacking Power cables, m ...

  • Cisco Systems UBR7225VXR - page 6

    6 Installation Tools and Equipment The tools and equipment listed below are recommended as th e minimum necessary to ins tall the Cisco uBR7225VXR router . Other equipment may include test equipment to c heck electronic and optical signal level s , power levels, and communicatio ns links. • Rack-mounting kit (includes brackets and screws) • Num ...

  • Cisco Systems UBR7225VXR - page 7

    7 For details about cabling specifications, refer to the Network Processing Engine and Networ k Services Engine Installation and Configuration guide at the following U RL: http://www.cisco.com/en/US/products/hw/cable/ps2217/prod_installation _guides_list.html Note A shielded CA T5e cable must be used to meet EMI Class A certification. For details a ...

  • Cisco Systems UBR7225VXR - page 8

    8 Rack-Mount Installation Guidelines • Allow sufficient clearance around the rack fo r maintenance.Y ou need 36 in. (91.44 cm) of clea rance to remove and replace system componen ts. • Always place the heavier equipment in the lower half o f the rack. • If the rack is provided with stabili zing devices, install the stabilizers before m ountin ...

  • Cisco Systems UBR7225VXR - page 9

    9 Attach the Rack-Mount Brackets to the Rear of the Chassis T o install the rack-mount brackets on the chassis for a re ar rack-mount configuration, complete the following steps: Step 1 Locate the threaded holes in the rear sides of the chassis. Step 2 Align the first rack-mount bracket to the threaded holes in one sid e of the chassis as shown in ...

  • Cisco Systems UBR7225VXR - page 10

    10 Step 3 Thread the four M4 x 6-mm Phillips flathead screws through the bracket and into the side of the chassis. Use a number 2 Phillips screwdriver to tigh ten the screws. Step 4 Repeat Step 1 through Step 3 for the other rack-mount bracket. Note Ensure you fasten the cable-management bracke t before installing the chassis in the rack. Attach th ...

  • Cisco Systems UBR7225VXR - page 11

    11 Installing the Cable-Management Bracket Before installing the chassis in the ra ck, both rack-mount brackets and the cabl e-management bracket must be installed. T o install the cable-management bra cket, complete the following steps: Step 1 Align the cable-management bracket with the two right front threaded holes in the chassis as shown in Fig ...

  • Cisco Systems UBR7225VXR - page 12

    12 Installing the Chassis in the Rack War ni ng This unit is intend ed for installation in restricted access are as. A restricted access area can b e accessed only through the use of a special tool, lock and key , or other means of security. Statement 1017 Caution Because the brackets support the weight of the entire ch assi s, be sure to use all o ...

  • Cisco Systems UBR7225VXR - page 13

    13 Connecting the Chassis to Ground Before connecting power and turning on the router , you must pr ovide an adequate ground conn ection for your system. T wo M5 ground receptacles provide a chassis ground connection for electrostatic discharge (E SD) and for your safety . A grounding lug mount is provided on the rear of the chassis. The mounting n ...

  • Cisco Systems UBR7225VXR - page 14

    14 T o connect th e Ci sco uBR7225VXR router chassis t o ground, complete the following steps : Step 1 Ensure that there is no power going to the router . Step 2 Use the wire stripper to strip approximately 0.75 in (2 cm) of shielding from one end of the 6-A WG wire. Step 3 Insert the stripped end of the wire into the wire receptacle on the groundi ...

  • Cisco Systems UBR7225VXR - page 15

    15 Step 2 Plug the power cab le into the AC connector of the power supply . Note For additional AC power cable strain relief, se cure the cabl e to the power supply handle by inserting a nylon cable tie through the hole in the handle and aro und the cable. Step 3 Plug the AC power supply cable into the AC power source. Repeat Step 1 through Step 3 ...

  • Cisco Systems UBR7225VXR - page 16

    16 7 Powering on the Cisco uBR7225VXR Router After installing your Cisco uBR7225VXR uni versal broadband router and connecting cables, check the following condi tions before powering on the router: • Every component is securely inserted in the right sl ot and the captive installation screws are tightened. • All network interface line cables are ...

  • Cisco Systems UBR7225VXR - page 17

    17 Identify Startup Problems Startup problems are commonly caused by source p ower problems or a board (network processing engine or cable interfa ce line card) that is not properly connected to the midplane. With the exception of the fa n tray a nd network processing engine, LEDs indicate all system states in the startup sequence. By checki ng the ...

  • Cisco Systems UBR7225VXR - page 18

    18 10 Obtaining Documentation and Submitting a Service Request For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’ s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at: http://www.cisco.com/en/US/docs/general/w ...

  • Cisco Systems UBR7225VXR - page 19

    Americas He adquarters Cisco Systems, Inc. San Jose, CA Asia Pacific Headqua rters Cisco Systems (USA) Pte. Ltd. Singapore Europe Head quarters Cisco Systems International BV Amsterdam, The Netherlands Cisco has more than 200 offices worldwide. Addres ses, phone numbers, and fax numbers are listed on the Cisco W ebsite at http://www.cisco.com/go/of ...

  • Cisco Systems UBR7225VXR - page 20

    20 ...

メーカー Cisco Systems カテゴリー Network Router

Cisco Systems UBR7225VXRのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- UBR7225VXRの取扱説明書
- Cisco Systemsの製品カード
- パンフレット
- またはCisco Systems UBR7225VXRの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Cisco Systems UBR7225VXRの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Cisco Systems UBR7225VXRの取り付け説明書、サービスマニュアル、簡易説明書、またはCisco Systems UBR7225VXRのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Cisco Systems UBR7225VXRの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Cisco Systems UBR7225VXRデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがCisco Systems UBR7225VXRを使用するのを助ける技術的文書のことです。説明書は通常、全てのCisco Systems UBR7225VXRユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Cisco Systemsの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Cisco Systems UBR7225VXRの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははCisco Systems UBR7225VXRの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Cisco Systems UBR7225VXRに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Cisco Systems UBR7225VXRデバイスの基本機能を使うにあたってのヒント。 Cisco Systems UBR7225VXRのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Cisco Systems UBR7225VXRに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるCisco Systems UBR7225VXRのメーカー/サービスへの連絡先に関する情報。

Cisco Systems UBR7225VXRについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもCisco Systems UBR7225VXRの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがCisco Systems UBR7225VXRで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)