-
Hitachi DH 40SA - page 1
...
-
Hitachi DH 40SA - page 2
1 1 3 5 7 8 9 8 10 11 B C D 12 9 6 4 2 3 A 4 1 7 A 0 2 1 6 5 ...
-
Hitachi DH 40SA - page 3
2 15 K 22 73 17 mm 7 mm P Q 21 O 20 19 J K J K 18 16 17 N J M L 13 14 F G E I H E J ...
-
Hitachi DH 40SA - page 4
...
-
Hitachi DH 40SA - page 5
4 English GENERAL OPERATIONAL PRECAUTIONS WARNING! When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury, including the following. Read all these instructions before operating this product and save these instructions. For safe operations: 1. Keep work area clean. ...
-
Hitachi DH 40SA - page 6
5 English SPECIFICATIONS Voltage (by areas)* (110V, 115V, 120V, 127V, 220V, 230V, 240V) Power input 950 W* Capacity Drill bit: 40 mm Core bit: 105 mm No load speed 360/min. Full-load impact rate 2800/min. Weight (without cord, side handle) 6.5 kg •Be sure to check the nameplate on product as it is subject to change by areas. STANDARD ACCESSORIES ...
-
Hitachi DH 40SA - page 7
6 English 䡬 Asphalt cutting (striking) 䡬 Syringe (for chip removal) 䡬 Hammer grease A 500 g (in a can) 30 g (in a green tube) Optional accessories are subject to change without notice. APPLICATIONS 䡬 Drilling holes in concrete 䡬 Drilling anchor holes 䡬 Crushing concrete, chipping, digging, and squaring (by applying optional accessories) ...
-
Hitachi DH 40SA - page 8
7 English 2. When a taper shank adapter is used. (Fig. 13) (1) Install drill bit with taper shank in the taper shank adapter. (2) Turn the power on and drill a base hole to the depth sounded by indicating groove on the drill bit. (3 ) After cleaning out dust with a syringe, attach the plug to the anchor tip and drive in the anchor with a manual ham ...
-
Hitachi DH 40SA - page 9
8 Español PRECAUCION ES GENERAL ES PARA OPERACIÓN ¡ADVERTENCIA! Cuando utilice herramientas eléctricas, tome las medidas de seguridad básicas para reducir el riesgo de incendios, descargas eléctricas, y lesiones, incluyendo lo siguiente. Lea todas todas estas instrucciones antes de utilizar este producto y guárdelas. Para realiza roperacione ...
-
Hitachi DH 40SA - page 10
9 Espa ñ ol PRECAUCIONES AL USAR EL MARTILLO ROTO-PERCUTOR 䡬 Usar protectores de o í dos durante el trabajo. 䡬 No tocar la broca durante ni inmdiatamente despu é s de trabajar, puesto que se pone ardiente y puede causar quemaduras serias. 䡬 Antes de empezar a romper, picar o perforar en una pared, suelo o techo, comprobar cuidadosamente qu ...
-
Hitachi DH 40SA - page 11
10 Espa ñ ol (1 ) Adaptador de anclaje (para rotaci ó n + percusi ó n) Tama ñ o de anclaje: W1/4, W5/16, W3/8, W1/2, W5/8 (N ° . 20) (N ° . 25) (N ° . 30) (N ° . 40) (N ° . 50) 䡬 Romper (Percusi ó n) 䡬 Excavar, ranurado y rebordes (percusi ó n) 䡬 Corte de asfalto (percusi ó n) 䡬 Jeringa (extracci ó n de res í duos) 䡬 Grasa A ...
-
Hitachi DH 40SA - page 12
11 Espa ñ ol Coloque el extremo de la broca de forma que entre en contacto con el hormig ó n, ponga en ON el interruptor de alimentaci ó n principal de la unidad, y realice la operaci ó n de calentamiento. Cerci ó rese de que se produzca un sonido de martilleo, y despu é s utilice la unidad. PRECAUCION Cuando haya realizado la operaci ó n de ...
-
Hitachi DH 40SA - page 13
12 Espa ñ ol (2) Aplicar 20g de grasa para martillo el é ctrico Hitachi tipo A (accesorio normales, contenida en tubo) en el c á rter. Como el tubo contiene 30g de grasa, proveer 2/3 de la grasa contenida. (3) Luego de cambiar la grasa, instalar la cubierta del cig ü e ñ al firmemente. NOTA La grasa A del martillo el é ctrico Hitachi es del t ...
-
Hitachi DH 40SA - page 14
...
-
Hitachi DH 40SA - page 15
...
-
Hitachi DH 40SA - page 16
...
-
Hitachi DH 40SA - page 17
...
-
Hitachi DH 40SA - page 18
...
-
Hitachi DH 40SA - page 19
18 ...
-
Hitachi DH 40SA - page 20
The exploded assembly drawing should be used only for authorized service center. ...
-
Hitachi DH 40SA - page 21
20 Item Part Name No. 5 7 Piston Pin 5 8 Connecting Rod Ass’y 5 9 Needle Bearing (NSK AJ50 1203) 6 0 Nylock Bolt (W/Flange) M6 × 25 6 1 Cylinder Case 6 2 O-Ring (1AS-60) 6 3 Needle Bearing (B) (NTN HMK4520) 6 5 Side Handle 6 6 Handle Holder 6 7 Handle Bolt 6 8 Stopper Rod 6 9 Ball Bearing (6202VVCMPS2S) 7 0 Dust Washer 7 1 O-Ring 7 2 Hex. Hd. Ta ...
-
Hitachi DH 40SA - page 22
901 Code No. C99075332 N Printed in Japan ...
Hitachi DH 40SAについてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもHitachi DH 40SAの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHitachi DH 40SAで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。