Windsor QQS28の取扱説明書

17ページ 0.35 mb
ダウンロード

ページに移動 of 17

Summary
  • Windsor QQS28 - page 1

    SABER/STRIDE II 28/34 98570 8/31/99 Y REV. OWNER’S GUIDE Read these instructions before operating the machine Antes de usar la máquina lea atentamente el libro de instrucciones Lire attentivement le mode d’emploi avant la mise en service de la machine Vor Inbetriebnahme der Maschine Bedienungsanweisung lesen Leggere queste istruzioni prima di ...

  • Windsor QQS28 - page 2

    2 MACHINE DATA LOG MODEL DATE OF PURCHASE SERIAL NUMBER SALES REPRESENTATIVE # DEALER NAME OPERATIONS GUIDE NUMBER PUBLISHED Copyright 1995 Windsor Industries, Printed in USA SABER/STRIDE II 28/34 98570 5/1/98 OVERVIEW The SABER/STRIDE II is a battery powered, self propelled, hard floor scrub- ber intended for commercial use. This appliance applies ...

  • Windsor QQS28 - page 3

    3 SABER/STRIDE II 28/34 98570 10/08/98 TABLE OF CONTENTS OPERATIONS Machine Data Log . . . . . . . . . . . . . . . . . . . . . . . . 2 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . 3 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Technical Specifications . . . . . . . . . . . . . . . . . . . . 5 O ...

  • Windsor QQS28 - page 4

    4 SAFETY SABER/STRIDE II 28/34 98570 7/14/98 The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard intensity identified by signal words - WARNING and CAUTION and FOR SAFETY. The level of hazard intensity is determined by the following definitions: WARNING - H ...

  • Windsor QQS28 - page 5

    5 TECHNICAL SPECIFICATIONS SABER/STRIDE II 28/34 98570 5/1/98 45” 69” View: Side view of machine MODEL: SABER/STRIDE II 28/34 Year of Construction: 1998 Nominal Power: 2.88 kW Mass: 850kg Rated Voltage: 36VDC Rated Amperage: 80 amps Cleaning Path: 28” (2 x 14”) S28, QQS28 34” (2 x 17”) S34, QQS34 34” (CYL) S34SP, QQS34SP Drive Motor: ...

  • Windsor QQS28 - page 6

    6 OPERATION CONTROLS SABER/STRIDE II 28/34 98570 5/1/98 1. Squeegee /Vacuum Switches. Turns on and off the vacuum and squeegee system seperately if desired. 2. Brush Pressure Indicator/Switch. Sets brush pressure on floor with LED’s to show pressure level. 3. One Touch Switch. Activates scrubbing and vacuuming functions. Pressing once turns “ON ...

  • Windsor QQS28 - page 7

    7 SABER/STRIDE II 28/34 98570 5/1/98 MACHINE OPERATION STARTING MACHINE NOTE: Perform pre-run machine check before operating machine. FOR SAFETY: Before starting machine, make sure that all safety devices are in place and operating properly. 1. Turn the key switch clockwise to the “ON” position. Move the directional control lever in the desired ...

  • Windsor QQS28 - page 8

    8 SABER/STRIDE II 28/34 98570 7/14/98 MACHINE OPERATION DOUBLE SCRUB Floors which are heavily soiled or have thick accumulations of floor finish may not clean sufficiently with one pass. In these cases it will be necessary to double scrub. To double scrub, begin scrubbing as usual, but after push- ing number 1, press the squeegee button to turn off ...

  • Windsor QQS28 - page 9

    9 MAINTENANCE SABER/STRIDE II 28/34 98570 7/14/98 SCRUB BRUSHES NOTE: All original equipment brushes are equipped with “Perform Alert © . This feature will tell the operator when it is time to replace the scrub brushes. “Perform Alert © brushes have bright yellow tufts located on these tufts are pre-trimmed to indicate the length of a worn ou ...

  • Windsor QQS28 - page 10

    10 MAINTENANCE SABER/STRIDE II 28/34 98570 7/14/98 SCRUB DECK SKIRT AND SQUEEGEE The skirts and squeegee should be inspected for wear and damage. The skirt is self adjusting. Replace skirt when they become cracked, worn, torn or brittle. SQUEEGEE BLADES NOTE: See page 15 of this guide for a complete table on squeegee options. The front squeegee bla ...

  • Windsor QQS28 - page 11

    11 MAINTENANCE SABER/STRIDE II 28/34 98570 7/14/98 ADJUSTING SQUEEGEE Adjusting the squeegee is a two part process. First, the squeegee tool must have correct pitch in order for the squeegee blade to have the same deflection at each tip as well as the center. The pitch adjustment on the SABER/STRIDE II is facilitated by the use of a spirit level mo ...

  • Windsor QQS28 - page 12

    12 BATTERIES SABER/STRIDE II 28/34 98570 7/14/98 The batteries provide the power to operate the machine. The standard are four 6 volt batteries rated at 250 A/h at a 6-hour rate. The batteries require regular maintenance to keep them operating at peak efficiency. The machine batteries will hold their charge for long peri- ods of time, but they can ...

  • Windsor QQS28 - page 13

    13 SABER/STRIDE II 28/34 98570 7/14/98 BATTERIES TO CHARGE THE BATTERIES When servicing machine, avoid contact with bat- tery acid. Batteries emit hydrogen gas. Explosion or fire can result. Keep sparks and open flame away. Keep covers open when charging. Wear eye protection and protective clothing when working with batteries. Charge batteries in a ...

  • Windsor QQS28 - page 14

    14 SERVICE SCHEDULE SABER/STRIDE II 28/34 98570 5/1/98 Maintenance Item Daily Weekly Monthly Annually Check Battery water level * Check Vac Hose Connections * Clean the Squeegee Blades * Inspect Brushes or Pads for debris ie: wire, string, wear * Inspect Vac fan shut off float screen * Drain & Rinse Tanks * Raise Squeegee Assembly * Raise Scrub ...

  • Windsor QQS28 - page 15

    15 SABER/STRIDE II 28/34 98570 9/15/98 SQUEEGEE BLADE/BRUSH HEAD OPTIONS P/N Desc. Color S28 / QQS28 S34 / QQS34 S34SP / QQS34SP 73932 FRONT, STANDARD RED X X standard 73934 REAR, STANDARD RED X standard 82529 REAR, LINATEX RED/NOTCH X option 82528 FRONT, LINATEX RED/NOTCH X X option 82638 REAR, (FOR TILE) BLUE X option 82637 FRONT, (FOR TILE) BLUE ...

  • Windsor QQS28 - page 16

    16 SERVICE LOCATION DETAILS SABER/STRIDE II 28/34 98570 5/1/98 2 BRUSH HEAD MODELS: S28, S34, QQS28, QQS34 3 4 2 CYLINDRICAL HEAD MODELS: S34SP, QQS34SP 3 4 7 6 5 2 SQUEEGEE ASSEMBLY SQUEEGEE ASSEMBLY CYLINDRICAL HEAD (OPTION) BRUSH HEAD 1 ALL MODELS (REF. ) CONTROL PANEL REAR ELECTRICAL ...

  • Windsor QQS28 - page 17

    SERVICE LOCATION PARTS LIST SABER/STRIDE II 28/34 98570 7/9/98 17 33 Ref Part No. Qty Description Serial No. Notes: From To 1 70532 6 SCR, 10-32 X 1/2 PPHMS BLK 2 80657 1 PIN, COTTER HAIR .148" DIA X 3/4 QTY 2 SEE NOTE * 3 87029 2 WASHER, 5/16 FLAT SS 4 48012 2 KNOB, 5/16-18 4 PRONG 5 82191 1 PIN, COTTER HAIR .178" DIA X 1" MODELS: S ...

メーカー Windsor カテゴリー Sander

Windsor QQS28のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- QQS28の取扱説明書
- Windsorの製品カード
- パンフレット
- またはWindsor QQS28の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Windsor QQS28の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Windsor QQS28の取り付け説明書、サービスマニュアル、簡易説明書、またはWindsor QQS28のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Windsor QQS28の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Windsor QQS28デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがWindsor QQS28を使用するのを助ける技術的文書のことです。説明書は通常、全てのWindsor QQS28ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Windsorの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Windsor QQS28の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははWindsor QQS28の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Windsor QQS28に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Windsor QQS28デバイスの基本機能を使うにあたってのヒント。 Windsor QQS28のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Windsor QQS28に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるWindsor QQS28のメーカー/サービスへの連絡先に関する情報。

Windsor QQS28についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもWindsor QQS28の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがWindsor QQS28で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)