日本語 dropdown-ico

Troy-Bilt TB3000の取扱説明書

22ページ 0.61 mb
ダウンロード

ページに移動 of 22

Summary
  • Troy-Bilt TB3000 - page 1

    ©2000 MTD SOUTHWEST INC Models TB3000 – 25cc Straight Shaft FORM 182823 (12/00) (10209 rev . A) Printed in U.S.A. Owner/Operator Manual 2-Cycle T rimmer • Safety • Assembly • Operation • Maintenance ...

  • Troy-Bilt TB3000 - page 2

    2 Introduction THANK YOU Thank you for buying this quality product. This modern outdoor power tool will provide many hours of useful service. Y ou will find it to be a great labor -saving device. This operator’ s manual provides you with easy-to-understand oper- ating instructions. Read the whole manual and follow all the instructions to keep you ...

  • Troy-Bilt TB3000 - page 3

    3 Ser vice Information SERVICE INFORMA TION Service on this unit both within and after the warranty period should be performed only by an authorized and approved service dealer . Dial: • 1-800-345-8746 for authorized service dealers in the United States Or • 1-800-668-1238 in Canada to obtain the listing of the authorized service dealer nearest ...

  • Troy-Bilt TB3000 - page 4

    The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and their explanations, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger . The instructions or warnings they give are not substitutes for proper accident prevention measur es. SYMBOL MEAN ...

  • Troy-Bilt TB3000 - page 5

    5 Safety (continued) • Always stop the engine and allow it to cool before filling the fuel tank. Never remove the cap of the fuel tank, or add fuel, when the engine is hot. Never operate the unit without the fuel cap securely in place. Loosen the fuel tank cap slowly to relieve any pressur e in the tank. • Add fuel in a clean, well-ventilated a ...

  • Troy-Bilt TB3000 - page 6

    6 Safety (continued) SAFETY AND INTERNA TIONAL SYMBOLS This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the operator's manual for complete safety , assembly , operating and maintenance and repair information. SYMBOL MEANING • SAFETY ALERT SYMBOL Indicates danger , wa ...

  • Troy-Bilt TB3000 - page 7

    SYMBOL MEANING • SHARP BLADE WARNING: Sharp blade on cutting attachment shield. T o pr event serious injury , do not touch line cutting blade. • CHOKE CONTROL A • ST ART position. B • RUN position. WARNING: The operation of any power tool can cause for eign objects to be thrown into your eyes. This can lead to severe eye damage. Befor e com ...

  • Troy-Bilt TB3000 - page 8

    8 Section 2 Know Y our Unit APPLICA TIONS As a trimmer; • Cutting grass and light weeds. • Edging • Decorative trimming around tr ees, fences, etc. With the optional brushcutter accessory kit; • Cutting weeds and light bush of up to 1/2 inch in diameter . Shaft Grip Cutting Attachment Shield Fuel Cap Throttle Contr ol D-Handle Line Cutting ...

  • Troy-Bilt TB3000 - page 9

    9 Section 3 Assembly On some units, the D-handle may be preinstalled and only requir e loosening the screws and adjusting the D-handle to the operator . Go to step 4 for adjusting the D-handle if preinstalled. INST ALLING AND ADJUSTING THE D-HANDLE 1. Remove the screws, nuts and bottom clamp piece that were installed on the D-handle for shipping. 2 ...

  • Troy-Bilt TB3000 - page 10

    10 Section 4 Oil and Fuel Oil and Gas Mixing Instructions Old and/or improperly mixed fuel ar e the main reasons for the unit not running pr operly . Be sure to use fresh, clean unleaded fuel. Follow the instructions carefully for the pr oper fuel/oil mixture. Definition of Blended Fuels T oday's fuels are often a blend of gasoline and oxygena ...

  • Troy-Bilt TB3000 - page 11

    11 Section 5 Operation ST ARTING INSTRUCTIONS Operate this unit only in a well ventilated area outdoors. Carbon monoxide exhaust fumes can be lethal in a confined area. Avoid accidental starting. Be in the starting position whenever pulling the starting rope. T o avoid serious personal injury , the operator and unit must be in a stable position whi ...

  • Troy-Bilt TB3000 - page 12

    12 Operation (continued) HOLDING THE TRIMMER Always wear eye, hearing, foot and body protec- tion to reduce the risk of injury when operating this unit. Before operating the unit, stand in the operating posi- tion (Fig. 5-4). Check for the following: • The operator is wearing eye protection and pr oper clothing. • The right arm is slightly bent ...

  • Troy-Bilt TB3000 - page 13

    13 Operation (continued) Fig. 5-6 DECORA TIVE TRIMMING Decorative trimming is accomplished by removing all vegetation around tr ees, posts, fences, etc. Rotate the whole unit so that the cutting attachment is at a 30° angle to the ground (Fig. 5-6). Section 6 MAINTENANCE NOTE: Some maintenance procedures may require special tools or skills. If you ...

  • Troy-Bilt TB3000 - page 14

    14 Maintenance (continued) Slotted Holes For Use with Membrane Line or Single Line For Use with Single Line ONL Y Loop Fig. 6-3 Fig. 6-4 LINE INST ALLA TION This section covers both Membrane line and standard single line installation. Always use manufacturer’ s 0.095 inch (2.41 mm) replacement line. Line other than specified may make the engine o ...

  • Troy-Bilt TB3000 - page 15

    15 Maintenance (continued) Membrane Line Installation 8. T ake approximately 20 feet (6.1 m) of new trimming line. Insert one end of the line through one of the two holes in the inner reel (Fig. 6-6). Pull the line through the inner r eel until only about 4 inches is left out. 9. Insert the end of the line into the open hole in the inner reel and p ...

  • Troy-Bilt TB3000 - page 16

    16 Fig. 6-9 Fig. 6-11 Fig. 6-12 Fig. 6-10 Maintenance (continued) AIR FIL TER MAINTENANCE Cleaning the Air Filter T o avoid serious personal injury , always tur n your trimmer off and allow it to cool befor e you clean or do any maintenance on it. Clean and re-oil the air filter every 10 hours of opera- tion. It is an important item to maintain. No ...

  • Troy-Bilt TB3000 - page 17

    17 Maintenance (continued) If after checking the fuel mixture and cleaning the air filter the engine still will not idle, adjust the idle speed screw as follows. 1. Start the engine and let it run at a high idle for a minute to warm up. 2. Release the throttle trigger and let the engine idle. If the engine stops, insert a small phillips or flat bla ...

  • Troy-Bilt TB3000 - page 18

    18 Maintenance (continued) ACCESSORIES/REPLACEMENT P ARTS Spark Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181765 Spark Arrestor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182153 Replacement Line Cartridge . . . . . . . . . . . . . . . . 49U5001L063 Inner Reel Spring . . . . . . . . . . . . . . . . . ...

  • Troy-Bilt TB3000 - page 19

    19 Section 7 T roubleshooting CAUSE ACTION Cutting attachment bound with grass Stop the engine and clean cutting attachment Cutting attachment out of line Refill with new line Inner reel bound up Replace the inner reel Cutting head dirty Clean inner reel and outer spool Line welded Disassemble, remove the welded section and rewind the line Line twi ...

  • Troy-Bilt TB3000 - page 20

    20 Section 8 Specifications Engine T ype . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air -Cooled, 2-Cycle Displacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Troy-Bilt TB3000 - page 21

    21 Notes ...

  • Troy-Bilt TB3000 - page 22

    MANUF ACTURER’S LIMITED W ARRANTY FOR: No implied warranty , including any implied warranty of merchantability or fitness for a particular purpose, applies after the applicable period of express written warranty above as to the parts as identified. No other express warranty or guaranty , whether written or oral, except as mentioned above, given b ...

メーカー Troy-Bilt カテゴリー Trimmer

Troy-Bilt TB3000のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- TB3000の取扱説明書
- Troy-Biltの製品カード
- パンフレット
- またはTroy-Bilt TB3000の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Troy-Bilt TB3000の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Troy-Bilt TB3000の取り付け説明書、サービスマニュアル、簡易説明書、またはTroy-Bilt TB3000のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Troy-Bilt TB3000の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Troy-Bilt TB3000デバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがTroy-Bilt TB3000を使用するのを助ける技術的文書のことです。説明書は通常、全てのTroy-Bilt TB3000ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Troy-Biltの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Troy-Bilt TB3000の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははTroy-Bilt TB3000の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Troy-Bilt TB3000に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Troy-Bilt TB3000デバイスの基本機能を使うにあたってのヒント。 Troy-Bilt TB3000のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Troy-Bilt TB3000に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるTroy-Bilt TB3000のメーカー/サービスへの連絡先に関する情報。

Troy-Bilt TB3000についてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもTroy-Bilt TB3000の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがTroy-Bilt TB3000で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)