-
Source Technologies STM.117B - page 1
Rev . 1.0 All specifications are subject to change without notice MOB ILE PRI NTE R MODEL : STm.117b ...
-
Source Technologies STM.117B - page 2
1 T able of Contents 1. Unpacking 3 2. Product overview 4 3. Usage and Installation 5 3-1. Control panel usage 5 3-2. Battery Installation 6 3-3. Battery char ging 7 3-4. Battery char ger usage 8 3-5. Usage of Cigar Jack for char ging 9 3-6. Roll paper installation 10 3-7. Leather case usage 11 3-8. Self test 12 4. Peripherals connection 13 4-1. Bl ...
-
Source Technologies STM.117B - page 3
2 3 2. Pr oduct overview P aper feed button P ower switch DC P ower Battery SERIAL USB Open Button Front Rear 1. Unpacking Printer Battery Serial Cable Roll paper USB Cable Shielded Charger CD Quick Manual Battery Holder (Cr adle) Leather case Shoulder strip Cigar Jack Charger Optional Standard ...
-
Source Technologies STM.117B - page 4
4 5 1. Align battery hook as shown in the picture 2. Push the battery into the printer until it locks in place. NOTE As the battery is not char ged at the time of your purchase, char ge the battery prior to using the printer (Battery char ger or Cradle can be used to char ge) CAUTION Risk of explosion if battery is replaced by an incorr ect type. D ...
-
Source Technologies STM.117B - page 5
6 7 3-4-1 The status of lamp in char ging 3-3-1 The status of lamp in char ging Status char ging charging complete Status char ging charging complete Char ging Lamp Char ging Lamp Red Red Green Green NOTE In the case the battery is not fixed properly in the holder , the red lamp will be blinking, Then, extract and reinsert the battery . 3-4 Batter ...
-
Source Technologies STM.117B - page 6
8 9 1 2 3 4 Press the PUSH button to open the paper cover Pull a short length of paper out of the printer and close the cover . Insert the paper in the right direction T ear off the additional paper using tear bar . 3-6 Roll Paper installation Connect the car cigar JACK char ger into the printer or battery holder . 3-5 Usage of Cigar Jack Char ger ...
-
Source Technologies STM.117B - page 7
10 11 1 2 3 NOTE T urn off the power pressing the power button for approximately 3 seconds. The printout is produced. While you are pr essing the FEED button, press the power button 3-8 Self T est 1. T o print ASCII pattern additionally , press the Feed button once mor e 2. After printing ASCII pattern, the self test will be finished automatically ...
-
Source Technologies STM.117B - page 8
12 13 1. Printer can be connected to the PDA and PC which can do wireless communication. 2. By using Bluetooth function supported in PC, printer can be connected. This printer can communicate with Peripherals device via Bluetooth and cables. 4-1 Bluetooth Connection 4. P eripherals connection When the printer is installed initially or when you face ...
-
Source Technologies STM.117B - page 9
14 15 4-2 Interface Cable Connection 1. Connect USB or Serial cable into the cable connector on the printer . 2. Connect the interface cable into the USB or Serial por t of the device (PDA, PC, etc.) NOTE Use the cable offered by the manufacturer (USB, Serial) Serial USB 5. Printer cleaning If the interior of the printer is dusty , printing quality ...
-
Source Technologies STM.117B - page 10
16 17 Printing Method Direct T hermal Printing Speed 80mm/sec Resolution 203 DPI X 203 DPI Character CPCL 7 Different Font Size (12~48pt) ESC/POS Font A (12X24), F ont B (9X17) Character per line Font A : 48pt , Font B : 64pt Character set ALPHA NUMERIC Character , Extension Character Barcode EAN-8, EAN-13, Code39, ITF , UPC-A, UPC-E, Codabar , Cod ...
-
Source Technologies STM.117B - page 11
18 19 Printer Commands Compatibility PRINT ○ FORM ○ JOURNAL ○ UNITS ○ Comments ○ TEXT Compatibility TEXT ○ FONT -GROUP(FG) ○ TEXT CONCA TENA TION ○ MUL TILINE(ML) ○ COUNT ○ SETMAG ○ SCALABLE TEXT X Linear Bar Codes Compatibility BARCODE ○ BARCODE-TEXT ○ T wo-Dimensional Bar Codes Compatibility PDF417 (POR T ABLE DA TA FILE ...
-
Source Technologies STM.117B - page 12
20 21 Line Print Mode Compatibility SETLP ○ SETLF ○ Moving With X and Y Coordinates ○ LMARGIN ○ SETBOLD ○ SETSP ○ Special ASCII Characters ○ SETFF ○ SET -TOF ○ SETLP-TIMEOUT ○ FCC Inform ation T his device complies with part 15 of the FCC Results. Operation is subject to the following two conditions: (1) This Device may not caus ...
-
Source Technologies STM.117B - page 13
22 23 C A UTION Antenna shall be mounted in such a manner to minimize the potential for human contact during normal operation. The antenna should not be contacted during operation to avoid the possibility of exceeding the FCC radio frequency exposure limit. T he device meets the FCC requirements for radio frequency (RF) radiation exposure in the st ...
Source Technologies STM.117Bについてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもSource Technologies STM.117Bの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがSource Technologies STM.117Bで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。