Philips CCZ092ATの取扱説明書

52ページ 0.59 mb
ダウンロード

ページに移動 of 52

Summary
  • Philips CCZ092AT - page 1

    Owner’s Manual Important! Return your Warranty Registration Card within 10 days. See why inside. Color TV with built-in VCR CCZ092AT CCZ092comb.QX33 4/5/99 6:05 PM Page 1 ...

  • Philips CCZ092AT - page 2

    CCZ092comb.QX33 4/5/99 6:05 PM Page 2 ...

  • Philips CCZ092AT - page 3

    Introduction 3 • Before doing anything else, record the TV/VCR’s model and serial num- bers in the spaces provided on page two. These numbers will help us assist you if you ever call for help. Helpful Hint Features • A-B Repeat Play • Automatic Channel Setup • Automatic Operation Features • Automatic Tracking Adjustment • Closed Capti ...

  • Philips CCZ092AT - page 4

    4 Table of Contents Setting Up Your TV/VCR Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Before Using the TV/VCR . . . . . . . . . . . . . ...

  • Philips CCZ092AT - page 5

    • The remote control and its batteries are supplied. • Do not mix alkaline and man- ganese batteries. • Do not mix old and new batteries. Before Using the TV/VCR 5 Putting Batteries in the Remote Control 1 Remove the battery compartment lid on the bottom of the remote control by sliding it in the direction of the arrow. 2 Place two AA batteri ...

  • Philips CCZ092AT - page 6

    6 Hooking Up the TV/VCR ANT. Hooking Up Your TV/VCR With a Cable Signal or Outdoor Antenna IN OUT ANT. Connect an RF coaxial cable (75- ohm, not supplied) to the OUT Jack on the Cable Box and to the ANT(enna) Jack on the TV/VCR. Connect a Cable signal or an anten- na to the ANT(enna) Jack. Hooking Up Your TV/VCR With a Cable Box To view any channel ...

  • Philips CCZ092AT - page 7

    • Do not watch TV while driving. • Use only the supplied car battery cord. Using another cord could damage the TV/VCR. • Make sure the cigarette lighter jack is free of ashes and other debris. • Make sure you push the car battery cord’s plug completely into the cigarette lighter. • Always unplug the car battery cord from the cigarette l ...

  • Philips CCZ092AT - page 8

    8 Turning On the TV/VCR Before you turn on the TV/VCR, make sure there are batteries in the remote control and the TV/VCR is hooked up correctly. The instructions on this page work only when you turn on the TV/VCR for the first time. 1 Press the POWER button. The TV/VCR will come on and the screen shown below will appear. 2 Press the Number 1 butto ...

  • Philips CCZ092AT - page 9

    Language Selection 9 Follow the steps below to change the language of the on-screen displays. 3 Press the Number 1 button to choose SELECT LAN- GUAGE. 4 Press the Number 1 button if you want the on-screen dis- plays in English. ON will appear to the right of ENGLISH on- screen. Or, press the Number 2 button if you want the on- screen displays in Sp ...

  • Philips CCZ092AT - page 10

    REW PLAY POWER SPEED MUTE SLEEP ALT.CH CHANNEL VOLUME REC/OTR STATUS/EXIT MEMORY PAUSE/STILL MENU CLEAR TRACKING STOP F.FWD o o p p o p o p 1 23 4 56 7 89 0 +100 10 Automatic Channel Setup Although the TV/VCR may automatically memorize the channels you receive when you turn it on for the first time, you may set up channels again by following the st ...

  • Philips CCZ092AT - page 11

    6 REW PLAY POWER SPEED MUTE SLEEP ALT.CH CHANNEL VOLUME REC/OTR STATUS/EXIT MEMORY PAUSE/STILL MENU CLEAR TRACKING STOP F.FWD o o p p o p o p 1 23 4 56 7 89 0 +100 Automatic Channel Setup (cont’d) 11 5 Within five seconds, press the Number 1 button to add that channel or the Number 2 button to delete that chan- nel. If you do not make a choice wi ...

  • Philips CCZ092AT - page 12

    REW PLAY POWER SPEED MUTE SLEEP ALT.CH CHANNEL VOLUME REC/OTR STATUS/EXIT MEMORY PAUSE/STILL MENU CLEAR TRACKING STOP F.FWD o o p p o p o p 1 23 4 56 7 89 0 +100 12 Setting the Clock • Entries that do not match the TV/VCR’s calendar will cause a question mark to appear on screen. • To make corrections while you are setting the clock, press th ...

  • Philips CCZ092AT - page 13

    Setting the Clock (cont’d) 13 5 Press two Number buttons for the hour(s) and two Number buttons for the minute(s). Then press 1 for AM or 2 for PM. For example, for 9:30 PM, press 09, 30, 2. SET MANUAL CLOCK TIME 09 : 30 PM MONTH – – / – – / – – TO CORRECT PRESS CLEAR TO END PRESS EXIT 6 Press two Number buttons for the month, two Num ...

  • Philips CCZ092AT - page 14

    14 Setting the Clock (cont’d) Automatic PBS Channel Selection 4 If ON appears beside AUTO CLOCK, press the MENU button. If OFF appears beside AUTO CLOCK, press the Number 1 button so that ON appears to the right of AUTO CLOCK, then press the MENU button. 1 Press the MENU button. 2 Press the PLAY/ ▲ button or the STOP/ ▼ button to select PRIM. ...

  • Philips CCZ092AT - page 15

    Setting the Clock (cont’d) 15 7 When the TV/VCR finds the PBS channel, the time will appear on-screen. Press the STATUS/EXIT button. 6 NOW SEARCHING flashes on the TV/VCR screen. However, you may see the message “PLEASE TURN OFF TO SET AUTO CLOCK PLEASE WAIT SEVERAL MINUTES.” If this mes- sage appears, turn off the TV/VCR for a few minutes. W ...

  • Philips CCZ092AT - page 16

    REW PLAY POWER SPEED MUTE SLEEP ALT.CH CHANNEL VOLUME REC/OTR STATUS/EXIT MEMORY PAUSE/STILL MENU CLEAR TRACKING STOP F.FWD o o p p o p o p 1 23 4 56 7 89 0 +100 16 Setting the Clock (cont’d) Manual PBS Channel Selection 4 If ON appears beside AUTO CLOCK, press the MENU button. If OFF appears beside AUTO CLOCK, press the Number 1 button so that O ...

  • Philips CCZ092AT - page 17

    Setting the Clock (cont’d) 17 8 When the TV/VCR finds the clock data, the time will appear on-screen. Press the STATUS/EXIT button. 6 Use the Number buttons to enter your PBS station. If you make a mistake, press the CLEAR button, then enter the correct number. ● If CANNOT FIND CLOCK DATA flashes on the TV/VCR screen and you know another PBS ch ...

  • Philips CCZ092AT - page 18

    18 Daylight-Saving Time 1 4 5 2 4 Press the Number 3 button so that ON or OFF appears beside DAYLIGHT SVG. TIME (Daylight-Saving Time). 5 Press the STATUS/EXIT button. 1 Press the MENU button. 2 Press the PLAY/ ▲ button or the STOP/ ▼ button to select PRIM. SETUP. Then, press the F.FWD/ B button. PRIMARY SETUP 1 SELECT LANGUAGE 2 AUTO PROGRAMMI ...

  • Philips CCZ092AT - page 19

    REW PLAY POWER SPEED MUTE SLEEP ALT.CH CHANNEL VOLUME REC/OTR STATUS/EXIT MEMORY PAUSE/STILL MENU CLEAR TRACKING STOP F.FWD o o p p o p o p 1 23 4 56 7 89 0 +100 Time Zone 19 4 1 5 6 3 2 When you set the clock using AUTO CLOCK, specify a time zone so the TV/VCR will maintain the clock according to your time zone. • If you select AUTO at step 5, t ...

  • Philips CCZ092AT - page 20

    20 Front Panel AUDIO VIDEO REC POWER REW PLAY F.FWD REC/OTR VOLUME CHANNEL PHONE STOP EJECT Cassette Compartment Insert a video cassette tape here. POWER Button Press to turn the power on or off. CHANNEL o / p Buttons Press to scan through the TV/VCR channels. During tape playback, press to adjust the tracking. Details are on page 45. Press the CHA ...

  • Philips CCZ092AT - page 21

    Rear Panel 21 ANT. DC 13.2V AC 120V ANT(enna) Jack Connect your antenna or cable here. Details are on pages six - seven. Antenna Hole Connect the stem of an indoor rod antenna here. Details are on page six. AC 120V Jack Connect the AC cord here. Details are on page seven. DC 13.2V Jack Connect the car battery cord here. Details are on page seven. C ...

  • Philips CCZ092AT - page 22

    22 Remote Control Buttons POWER Button Press to turn on or off the TV/VCR. SPEED Button Press to select the recording speed (SP, LP, or SLP). PLAY/ ▲ Button Press to play a tape. Details are on page 28. Also, press to release Search or Still mode and return to normal playback. Details are on page 46. Press to select an item in the pop up menu. RE ...

  • Philips CCZ092AT - page 23

    Remote Control Buttons (cont’d) 23 STOP/ ▼ Button Press to stop the tape. Press to select an item in the on-screen menu. PAUSE/STILL Button During recording, press to temporarily stop the recording. Press again to resume recording. Details are on page 29. You cannot pause a One-Touch Recording. During tape playback, press to freeze the picture ...

  • Philips CCZ092AT - page 24

    REW PLAY POWER SPEED MUTE SLEEP ALT.CH CHANNEL VOLUME REC/OTR STATUS/EXIT MEMORY PAUSE/STILL MENU CLEAR TRACKING STOP F.FWD o o p p o p o p 1 23 4 56 7 89 0 +100 TO ADJUST PRESS s / B 24 Adjusting the Picture Controls Follow these steps to adjust the TV/VCR’s brightness, picture, color, tint, and sharpness. 1 Press the MENU button. 4 2 Press the ...

  • Philips CCZ092AT - page 25

    Adjusting the Picture Controls (cont’d) 25 Decrease Increase BRIGHTNESS decreased brightness increased brightness PICTURE decreased contrast increased contrast COLOR paler more brilliant TINT more purple more green SHARPNESS softer clearer Press the REW(ind)/ s button to decrease a picture control. Press the F.FWD / B button to increase a picture ...

  • Philips CCZ092AT - page 26

    • If the channel you select has no broadcast, the screen will be solid blue. • You cannot view closed captions during recording or tape playback if COUNTER ONLY is selected at step 4. Details are on pages 38 - 39. Helpful Hints 1 Press the MENU button. Function Button Pressed Time Channel Counter and Counter Memory Tape Speed 12:00 AM STOP CH10 ...

  • Philips CCZ092AT - page 27

    REW PLAY POWER SPEED MUTE SLEEP ALT.CH CHANNEL VOLUME REC/OTR STATUS/EXIT MEMORY PAUSE/STILL MENU CLEAR TRACKING STOP F.FWD o o p p o p o p 1 23 4 56 7 89 0 +100 Reminder 27 The channel number will remain on-screen at all times when you set REMINDER to ON in the pop up menu. The exception is dur- ing tape playback, Forward and Reverse Searching, St ...

  • Philips CCZ092AT - page 28

    REW PLAY POWER SPEED MUTE SLEEP ALT.CH CHANNEL VOLUME REC/OTR STATUS/EXIT MEMORY PAUSE/STILL MENU CLEAR TRACKING STOP F.FWD o o p p o p o p 1 23 4 56 7 89 0 +100 28 Playing • If the tape you want to play is already in the TV/VCR, turn on the TV/VCR power, then press the PLAY/ ▲ button. • Playback features and options are on pages 41 - 46. Hel ...

  • Philips CCZ092AT - page 29

    REW PLAY POWER SPEED MUTE SLEEP ALT.CH CHANNEL VOLUME REC/OTR STATUS/EXIT MEMORY PAUSE/STILL MENU CLEAR TRACKING STOP F.FWD o o p p o p o p 1 23 4 56 7 89 0 +100 Recording 29 • You cannot record one channel while watching another. • Recording options are on pages 30 - 36. • You cannot record if RECORD DEFEAT is set to ON. (REC DEFEATED will f ...

  • Philips CCZ092AT - page 30

    30 One-Touch Recording The One-Touch Recording (OTR) function allows you to program an immediate timed recording from 30 minutes to eight hours long without setting the timer. Before you begin, make sure: ● Channels are set up. ● There is a tape in the TV/VCR. The record tab must be intact. 1 Use the CHANNEL ▲ / ▼ buttons or the Number butt ...

  • Philips CCZ092AT - page 31

    Rerecording (Tape Duplication) 31 • To exit line input mode (A/V IN), press the Number buttons or the CHANNEL ▲ / ▼ buttons to select a channel other than 00. • Unauthorized recording of copy- righted television programs, video tapes, or other materials may infringe on the rights of copyright owners and violate copyright laws. • Different ...

  • Philips CCZ092AT - page 32

    REW PLAY POWER SPEED MUTE SLEEP ALT.CH CHANNEL VOLUME REC/OTR STATUS/EXIT MEMORY PAUSE/STILL MENU CLEAR TRACKING STOP F.FWD o o p p o p o p 1 23 4 56 7 89 0 +100 32 Timer Recording Follow the steps below to program the TV/VCR to record TV programs while you’re away from home. The TV/VCR will turn itself on, record, and turn itself off automatical ...

  • Philips CCZ092AT - page 33

    ONE TIME PROGRAM PROGRAM 1 CHANNEL – – TO CORRECT PRESS CLEAR TO END PRESS EXIT Timer Recording (cont’d) 33 5 ● If you are using an antenna or cable connection, enter the chan- nel of the TV program you want to record (you must enter a 0 before all single-digit channels). ● If you are recording from line input, press 0, 0. A/V IN will app ...

  • Philips CCZ092AT - page 34

    34 Timer Recording (cont’d) 8 Press the Number 1 button to record in SP speed, press the Number 2 button to record in LP speed, or press the Number 3 button to record in SLP speed. Details about tape speed are on page 29. You cannot use the (Tape) SPEED button at this time. 9 Press two Number buttons for the month and two Number buttons for the d ...

  • Philips CCZ092AT - page 35

    Timer Recording (cont’d) 35 6 Repeat steps 1 - 4 to make sure you have cleared the cor- rect position. REW PLAY POWER SPEED MUTE SLEEP ALT.CH CHANNEL VOLUME REC/OTR STATUS/EXIT MEMORY PAUSE/STILL MENU CLEAR TRACKING STOP F.FWD o o p p o p o p 1 23 4 56 7 89 0 +100 Checking or Clearing Timer Recordings 1 With the TV/VCR on, press the MENU button. ...

  • Philips CCZ092AT - page 36

    36 Record Defeat Follow the steps below to prevent accidental recording. 2 Press the PLAY/ ▲ button or the STOP/ ▼ button to select VCR SETUP, then press the F.FWD/ B button. 3 Press the Number 4 button so that ON appears beside RECORD DEFEAT. 4 Press the STATUS/EXIT button. • If you set RECORD DEFEAT to ON after a timer recording has been se ...

  • Philips CCZ092AT - page 37

    Setting the Sleep Timer 37 Use the sleep timer to program the TV/VCR to shut off in a cer- tain amount of time. 1 Press the SLEEP button. The sleep timer display will appear on-screen. (You can not set the sleep timer during a recording.) 1-2 • Finish all recordings before the TV/VCR shuts itself off. If a record- ing is in progress, the sleep ti ...

  • Philips CCZ092AT - page 38

    REW PLAY POWER SPEED MUTE SLEEP ALT.CH CHANNEL VOLUME REC/OTR STATUS/EXIT MEMORY PAUSE/STILL MENU CLEAR TRACKING STOP F.FWD o o p p o p o p 1 23 4 56 7 89 0 +100 When you watch a program that is being broadcast with closed captions, you can access on-screen boxes containing the pro- gram’s dialogue (for example, what a character is saying), dialo ...

  • Philips CCZ092AT - page 39

    Closed Caption (cont’d) 39 • You cannot view closed captions during recording or tape playback if COUNTER ONLY is set. • Abbreviations, symbols, and other grammatical shortcuts are often used in order to keep pace with the on-screen action. This does not indi- cate a problem with the TV/VCR. • To cancel closed captions, follow steps 1 - 2 o ...

  • Philips CCZ092AT - page 40

    REW PLAY POWER SPEED MUTE SLEEP ALT.CH CHANNEL VOLUME REC/OTR STATUS/EXIT MEMORY PAUSE/STILL MENU CLEAR TRACKING STOP F.FWD o o p p o p o p 1 23 4 56 7 89 0 +100 Usually, the volume bar appears when you press the VOLUME ▲ / ▼ buttons. If you do not need it, set the VOLUME BAR to OFF position. For example, when you watch a program that is being ...

  • Philips CCZ092AT - page 41

    Repeat Play 41 Follow the steps below to program the TV/VCR to play a tape over and over. 2 Press the PLAY/ ▲ button or the STOP/ ▼ button to select VCR SETUP, then press the F.FWD/ B button. 3 Press the Number 2 button so that ON appears beside REPEAT PLAY. 4 Press the STATUS/EXIT button. Now, when a tape has fin- ished playing, the TV/VCR wil ...

  • Philips CCZ092AT - page 42

    42 A - B Repeat Play • To cancel A-B Repeat Play, set ONE TIME PLAY to ON. To set ONE TIME PLAY to ON, follow steps 1 - 3 above. Then, press the Number 1 button so that ON appears beside ONE TIME PLAY. Press the STA- TUS/EXIT button. • The end position (B) must be later on the tape than the start position (A). Helpful Hints Follow the steps bel ...

  • Philips CCZ092AT - page 43

    5 Press the STATUS/EXIT button to remove the display. A- B REPEAT will appear on-screen. Beneath it, the letter A will flash beside the real-time counter. . A-B REPEAT A 1:23:45 6 Play, fast forward, or rewind the tape to the position at which you want to begin playback. Stop the tape, then press the MEMORY button to set the start position (A). The ...

  • Philips CCZ092AT - page 44

    REW PLAY POWER SPEED MUTE SLEEP ALT.CH CHANNEL VOLUME REC/OTR STATUS/EXIT MEMORY PAUSE/STILL MENU CLEAR TRACKING STOP F.FWD o o p p o p o p 1 23 4 56 7 89 0 +100 44 Real-Time Counter Memory Follow the steps below to reset the real-time counter to zero at a tape location you want to refer to later. 1 Play, fast forward, or rewind a tape to the locat ...

  • Philips CCZ092AT - page 45

    Automatic Operation Features 45 The following playback features will always operate. Automatic Playback When you put a tape in the TV/VCR, the power will come on automatically. If the tape’s record tab is missing, playback will begin. If a timer recording is set, the power will not come on automatically when you insert a tape with the record tab ...

  • Philips CCZ092AT - page 46

    46 Playback Options Forward and Reverse Searching (SP/LP/SLP) 1 During tape playback, press and release the F.FWD / B button or the REW(ind)/ s button. A fast forward or reverse picture search will begin. 2 To return to normal playback, press the PLAY/ ▲ button. Super High Speed Searching (LP/SLP) 1 During tape playback, press the F.FWD / B butto ...

  • Philips CCZ092AT - page 47

    Specifications General CRT: 9-inch in line gun Television system: NTSC-M Closed caption system: Section 15.119, FCC (Federal Communications Commission) Standard Video Heads: Two heads Tape width: 1/2 inch (12.65 mm) Tape speed SP: 33.35 mm/sec. LP: 16.67 mm/sec. SLP: 11.12 mm/sec. Operating Temperature: 41˚F (5˚C) to 104˚F (40˚C) Relative Humid ...

  • Philips CCZ092AT - page 48

    If you are having problems with your product, check this list of problems and possible solutions before requesting service. You may be able to solve the problem yourself. If you need to call a customer service representative, please know the model number and serial number of your product before you call. This information is displayed on the back of ...

  • Philips CCZ092AT - page 49

    Helpful Hints (cont’d) 49 The remote control is not available, or the remote control will not access the pop up menu. • Use the buttons on the front panel of the TV/VCR to access the pop up menu (page 20). You can not enter numbers (for example, to program a timer recording) using the front panel buttons. TV/VCR power shuts off after 15 minutes ...

  • Philips CCZ092AT - page 50

    50 Limited Warranty WHO IS COVERED? You must have proof of purchase to receive warranty service. A sales receipt or other document showing that you purchased the product is considered proof of purchase. WHAT IS COVERED? Warranty coverage begins the day you buy your product. For 90 days thereafter, all parts will be repaired or replaced, and labor i ...

  • Philips CCZ092AT - page 51

    a-b repeat play . . . . . . . .42 - 43 ac 120v jack . . . . . . . . . . . .7, 21 accessories . . . . . . . . . . . . . . .52 ant(enna) jack . . . . . . . . . . .6, 21 audio jack . . . . . . . . . . . . .20, 31 automatic playback . . . . . . . . . . . . . . .45 rewind . . . . . . . . . . . . . . . .45 batteries . . . . . . . . . . . . . . . . . .5 b ...

  • Philips CCZ092AT - page 52

    IB8044E001 Printed In Malaysia 0EMN01336 / B4908UJ * * * * * S UPPLIED A CCESSORIES Check to be sure the items on this page are packed with your TV/VCR. These accessories are provided to help you use or set up your TV/VCR. If any of these items are not included, or if you need to replace an item, contact Philips Service Solutions Group at the addre ...

メーカー Philips カテゴリー TV VCR Combo

Philips CCZ092ATのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- CCZ092ATの取扱説明書
- Philipsの製品カード
- パンフレット
- またはPhilips CCZ092ATの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Philips CCZ092ATの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Philips CCZ092ATの取り付け説明書、サービスマニュアル、簡易説明書、またはPhilips CCZ092ATのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Philips CCZ092ATの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Philips CCZ092ATデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがPhilips CCZ092ATを使用するのを助ける技術的文書のことです。説明書は通常、全てのPhilips CCZ092ATユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Philipsの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Philips CCZ092ATの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははPhilips CCZ092ATの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Philips CCZ092ATに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Philips CCZ092ATデバイスの基本機能を使うにあたってのヒント。 Philips CCZ092ATのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Philips CCZ092ATに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるPhilips CCZ092ATのメーカー/サービスへの連絡先に関する情報。

Philips CCZ092ATについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもPhilips CCZ092ATの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPhilips CCZ092ATで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)