日本語 dropdown-ico

Porter-Cable RS830の取扱説明書

30ページ 1.34 mb
ダウンロード

ページに移動 of 30

Summary
  • Porter-Cable RS830 - page 1

    INSTRUCTION MANUAL 10" Pr ofessional Radial Arm Saw (Model RS830) P ART NO. 424-12-651-0034 - 08-23-02 Copyright © 2002 Delta Machinery ESP AÑOL: PÁGINA 31 T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-8 ...

  • Porter-Cable RS830 - page 2

    2 GENERAL SAFETY RULES W oodworking can be dangerous if safe and pr oper operating procedures ar e not followed. As with all machinery , there are certain hazar ds involved with the operation of the product. Using the machine with respect and caution will considerably lessen the possibility of personal injury . However , if normal safety precaution ...

  • Porter-Cable RS830 - page 3

    3 ADDITIONAL SAFETY RULES FOR RADIAL ARM SA WS WARNING : F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS PERSONAL INJURY . 1. DO NOT OPERA TE THIS MACHINE UNTIL it is assembled and installed according to the instructions. 2. OBT AIN ADVICE from your supervisor, instructor , or another qualified person if you are not familiar with the operati ...

  • Porter-Cable RS830 - page 4

    4 POWER CONNECTIONS A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wire extension cords which have 3- prong gr ounding type plugs and matching receptacle which will accept the machine’ s pl ...

  • Porter-Cable RS830 - page 5

    Use proper extension cor ds. Make sure your extension cord is in good condition and is a 3-wir e extension cord which has a 3-prong gr ounding type plug and matching receptacle which will accept the machine’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the current of the machine. An undersized cord will cause a ...

  • Porter-Cable RS830 - page 6

    6 UNP ACKING AND CLEANING Carefully unpack the machine and all loose items fr om the shipping container(s). Remove the protective coating from all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gasoline or lacquer thinner for this purpose). After cleaning, cover the unpainted surfaces ...

  • Porter-Cable RS830 - page 7

    7 RADIAL ARM SA W P AR TS Fig. 4 1 2 3 1. Radial Arm Saw 2. Legs (4) 3. T able Supports (2) 4. 5/16-18x5/8" Carriage Head Screws (16) 4 5 6 7 5. 5/16" Flat Washers (16) 6. 5/16" Exter nal T ooth Lockwashers (16) 7. 5/16-18 Hex Nuts (16) ...

  • Porter-Cable RS830 - page 8

    8 T ABLE BOARD P ARTS Fig. 5 1 2 3 4 5 6 1. Fence Board 2. Middle T able Board 3. Rear T able Board 4. Front T able Boar d 5. 7/8" Open End - 1/2" Box Wrench 6. 7/8" x 1/2" Box Wrench 7. 1/4-20x1¼" Round Head Screw (4) 8. 1/4-20x1" Round Head Screw (4) 9. 5/16-18x5/8" Carriage Head Screw (6) 10. #10x1/2" She ...

  • Porter-Cable RS830 - page 9

    9 ASSEMBL Y WARNING: FOR YOUR OWN SAFETY , DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETEL Y ASSEMBLED AND YOU READ AND UNDERST AND THE ENTIRE INSTRUCTION MANUAL. LEGS TO SA W BASE 1. Loosen lock knob (A) Fig. 8, and move cutting-head (B) to the rear position as shown. Then tighten knob (A). 2. IMPORT ANT : Make certai ...

  • Porter-Cable RS830 - page 10

    10 REMOVING BLADE AND BLADE GUARD FROM SA W 1. DISCONNECT MACHINE FROM POWER SOURCE . 2. Loosen blade guard clamp knob (A) Fig. 11, and rotate blade guar d (B) to the position shown. Fig. 11 A B 3. With wrenches (C) Fig. 12, loosen arbor nut (D) as much as possible. NOTE: Arbor nut has left hand threads . Fig. 12 B C D F G 4. Lift cam (E) Fig. 13, ...

  • Porter-Cable RS830 - page 11

    11 T ABLE SUPPOR TS 1. Place front table board (A) Fig. 16, on a stable surface with counter -bored holes facing down, as shown. 2. Fasten left and right table supports (B) Fig. 16, to bottom of front table boar d (A) as shown, by inserting four 1/4-20x1" round head scr ews up through counterbored holes (D), in table boar d (A) and table suppo ...

  • Porter-Cable RS830 - page 12

    12 6. When both right and left edges of the table board are the same distance fr om the table supports, tighten four screws located in holes (N) Fig. 21, of front table board (A). Fig. 21 N N R R R R A 7. Insert four 1/4-20x1-1/4" round head screws (P) Fig. 22, into holes (R) Figs. 21 and 22, of the table board as shown, and tighten each of th ...

  • Porter-Cable RS830 - page 13

    13 11. Place an arbor wrench (D) Fig. 25, between table board (A) and motor shaft (B). Lower track arm (X) Fig. 24, by turning elevating handle (C) counterclockwise until motor shaft (B) Fig. 25, barely touches arbor wrench. Fig. 25 Fig. 26 Fig. 27 Fig. 28 12. Check the height of the table board above the other three table boar d adjustment screws ...

  • Porter-Cable RS830 - page 14

    14 T ABLE BOARD CLAMPS AND T ABLE BOARDS 1. Locate table board clamps (A) Fig. 29, and insert one clamp into each of the slotted holes (B) located at the rear of each table support bracket (C) as shown in Fig. 30. Fig. 29 Fig. 30 Fig. 31 Fig. 32 2. T ur n adjusting screw (D) Fig. 30 counter clockwise, so that the knobs (A) are in the r ear position ...

  • Porter-Cable RS830 - page 15

    15 Fig. 33 Fig. 34 Fig. 36 Fig. 35 4. Loosen cutting-head clamp knob (S) Fig. 33, and slide cutting-head (T) the entire length of track arm (A) as shown to determine if blade (C) travels parallel to the square (E). 5. If an adjustment is necessary , loosen index ring locking screw (J) Fig. 34, and track arm clamp handle (K). 6. Rotate track arm (A) ...

  • Porter-Cable RS830 - page 16

    16 Fig. 37 Fig. 38 Fig. 39 Fig. 40 REMOVING “HEELING” IN SA W BLADE CUT Even though the cutting-head travel may be perfectly aligned at 90 degrees to the fence, the blade itself may not be 90 degrees or squar e with the fence, as shown in Fig. 37. This condition is known as “heeling.” T o check and adjust, proceed as follows: 1. DISCONNECT ...

  • Porter-Cable RS830 - page 17

    17 5. Place a square (D) Fig. 41, on the table and against the saw blade, as shown, and check to see if the blade is square with the table. NOTE: The square should r est between two teeth of the saw blade . 6. If an adjustment is necessary , make certain bevel clamp lever (C) Fig. 40, is tight. Remove screw , flat washer , and pointer (E) Fig. 40. ...

  • Porter-Cable RS830 - page 18

    18 ASSEMBLING BLADE AND BLADE GUARD TO MACHINE 1. DISCONNECT MACHINE FROM POWER SOURCE . USE ONL Y 10" BLADES WITH 5/8" ARBOR HOLES AND RA TED FOR 5000 RPM OR HIGHER. 2. Assemble the inside (thick) arbor flange (A) Fig. 44, onto the arbor shaft with the recessed side of flange (A) facing out. 3. With the blade guard (B) Fig. 45, in the le ...

  • Porter-Cable RS830 - page 19

    19 CUTTING INTO T ABLE BOARDS 1. Assemble table boards (A) Fig. 48, and fence (B) as shown and secure in place with table clamps, one of which is shown at (C). Fig. 48 Fig. 49 Fig. 50 Fig. 51 2. Retur n cutting-head (D) Fig. 49, to rear of track arm (E), and tighten cutting-head clamp knob (G) Fig. 48. Make sure switch (H) Fig. 49, is in the “OFF ...

  • Porter-Cable RS830 - page 20

    20 OPERA TING CONTROLS AND ADJUSTMENTS ST AR TING AND STOPING RADIAL ARM SA W The on/off switch (A) Fig. 56, is located at the front of the cutting-head. T o tur n the saw “ON” move the switch (A) Fig. 56, up to the “ON” position. T o tur n the saw “OFF” move the switch (A) Fig. 56, down to the “OFF” position. LOCKING SWITCH IN THE ...

  • Porter-Cable RS830 - page 21

    21 5. Using a 3/16" Allen wr ench (J) Fig. 64, tur n adjustment screws (K) Figs. 61 and 64 to remove all “play .” NOTE: DO NOT OVERTIGHTEN ADJUSTMENT SCREWS (K). THIS CAN DAMAGE BEARINGS . WARNING: DO NOT LOOSEN ADJUSTMENT SCREWS (K) MORE THAN 1/2 TURN. THE CUTTING- HEAD MA Y F AL L FROM THE TRACK ARM. 6. Tighten two hex nuts which wer e l ...

  • Porter-Cable RS830 - page 22

    22 3. Rotate hex bolt (B) Fig. 67, in the desired direction which the handle needs to be turned. 4. Push hex bolt (B) Fig. 67, back through hole. Make certain head of hex bolt is seated properly in r ecessed bushing (C), and reassemble track arm clamping lever . NOTE: If track arm clamping lever (A) Fig. 66, tightens before appr oximately four tur ...

  • Porter-Cable RS830 - page 23

    23 POSITIVE STOP YOKE INDEX Y oke index lever (A) Fig. 71, activates a positive stop which positions the cutting-head in the cross-cut or rip position. T o rotate the cutting-head, release yoke clamp handle, press up or down on yoke index lever (A), releasing the positive stop, and r otate the cutting-head to the #1 in-rip or #2 out-rip or #3 cross ...

  • Porter-Cable RS830 - page 24

    24 EXPLANA TION OF OPERA TING CONTROLS The following is an explanation of the operating controls of the Delta 10" Radial Saw . W e suggest you study these explanations carefully to familiarize yourself with the contr ols before turning on the power . Doing otherwise may cause damage to the saw or personal injury (Figs. 74 and 75). Fig. 74 Fig. ...

  • Porter-Cable RS830 - page 25

    25 AUXILIAR Y T ABLE BOARD F ACING T o prevent repeated cutting into the table surface which will eventually cause the table to sag, an auxiliary table boar d facing can be cut and fitted to the table. It can be made from 1/4" plywood or particle boar d and should be cut to a size that will exactly cover all of the table boards in fr ont of th ...

  • Porter-Cable RS830 - page 26

    26 COMPOUND MITER CUTTING Compound miter cutting is performed in the same manner as miter cutting except the saw blade is also tilted to cut a bevel. The settings and operation are similar to mit er cu tting except that the blade is first tilted to the desired angle on the bevel scale befor e it is clamped in place. Fig. 79, shows a compound miter ...

  • Porter-Cable RS830 - page 27

    27 MAINTENANCE OVERLOAD PROTECTION The motor on your saw is equipped with a resettable overload relay (A) Fig. 82. If the motor shuts off or fails to start due to overloading, or low voltage, turn the switch to the “OFF” position, let the motor cool three to five minutes then push the reset button (A). The motor can then be turned on again in t ...

  • Porter-Cable RS830 - page 28

    28 CONSTRUCTING A PUSH STICK When ripping work less than 4 inches wide, a push stick should be used to complete the feed and could easily be made from scrap material by following the pattern shown in Fig. 82. Fig. 83 PUSH STICK MAKE FROM 1/2" OR 3/4" WOOD OR THICKNESS LESS THAN WIDTH OF MA T’L. TO BE CUT NOTCH TO HELP PREVENT HAND FROM ...

  • Porter-Cable RS830 - page 29

    29 NOTES ...

  • Porter-Cable RS830 - page 30

    30 T wo Y ear Limited W arranty Delta will repair or r eplace, at its expense and at its option, any Delta machine, machine part, or machine accessory which in normal use has proven to be defective in workmanship or material, pr ovided that the customer returns the product prepaid to a Delta factory service center or authorized service station with ...

メーカー Porter-Cable カテゴリー Saw

Porter-Cable RS830のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- RS830の取扱説明書
- Porter-Cableの製品カード
- パンフレット
- またはPorter-Cable RS830の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Porter-Cable RS830の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Porter-Cable RS830の取り付け説明書、サービスマニュアル、簡易説明書、またはPorter-Cable RS830のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Porter-Cable RS830の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Porter-Cable RS830デバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがPorter-Cable RS830を使用するのを助ける技術的文書のことです。説明書は通常、全てのPorter-Cable RS830ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Porter-Cableの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Porter-Cable RS830の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははPorter-Cable RS830の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Porter-Cable RS830に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Porter-Cable RS830デバイスの基本機能を使うにあたってのヒント。 Porter-Cable RS830のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Porter-Cable RS830に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるPorter-Cable RS830のメーカー/サービスへの連絡先に関する情報。

Porter-Cable RS830についてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもPorter-Cable RS830の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPorter-Cable RS830で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)