-
Jet Tools DC-1100G - page 1
Operating Instructions and Parts Manual Dust Collector Model: DC-1100A/C/RC DC-1100A/RC DC-1100C/RC WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60123 Part No. M-708639 Ph.: 800-274-6848 Revision G 07/04 www.wmhtoolgroup.com Copyright © WMH Tool Group This Manual is Bookmarked ...
-
Jet Tools DC-1100G - page 2
2 This manual has been prepared fo r the owner and operators of JET DC-11 00 Series Dust Collectors. Its purpose, aside from machine operatio n, is to prom ote safety using accepted operatin g and maintenance procedures. To obtain maximum life and efficiency from your du st collector and to aid in using it safely, please read this manual thoroughly ...
-
Jet Tools DC-1100G - page 3
3 Table of Contents Warranty and Service ........................................................................................................... ................................ 2 Table of Contents .............................................................................................................. .................................... ...
-
Jet Tools DC-1100G - page 4
4 Warnings 1. Read and understand the entire o wners manual before attempting assembly or operation. 2. Read and un derstand the warnings posted on the machi ne and in this manual. Failure to co mply with all of these warnings may cause serious inju ry. 3. Replace the warning labels if they become obscu red or removed. 4. This du st collector is de ...
-
Jet Tools DC-1100G - page 5
5 blahblahblah 20. Make your workshop child proof with padlocks , master switc hes or by removing starter keys. 21. Give your work undivided attention. Loo king arou nd, carrying on a conversation a nd “horse-play” are careless acts that can result in seriou s injury. 22. Do not use the dust colle ctor for anything except wood dust. Materials s ...
-
Jet Tools DC-1100G - page 6
6 Introduction This manual is provided by JET covering the safe operation and maintenan ce procedures for model DC-1100 Series Dust Collectors. This manual contains instructions on inst allation, safety precaution s, general operating procedures, maintenance in structions and par ts breakdown. Thi s machine has been designe d and constructed to pro ...
-
Jet Tools DC-1100G - page 7
7 Unpacking DC-1100A/RC Dust Collector 1. Remove all contents fr om the shipping carton. 2. Report any damage to your distributor. 3. Do not discard any shipping material until after the dust collector has been assembl ed and is running properly. Contents of the Shipping Carto n 1 – Upper Bag Hanger 1 – Base 1 – Housing 1 – Hanger Bracket 1 ...
-
Jet Tools DC-1100G - page 8
8 Unpacking DC-1100C/RC Dust Collector 1. Remove all contents fr om the shipping carton. 2. Report any damage to your distributor. 3. Do not discard any shipping material until after the dust collector has been assembl ed and is running properly. Contents of the Shipping Carto n Canister Filter Box 1 – Canister Filter 1 – Handle 1 – Bag of Ha ...
-
Jet Tools DC-1100G - page 9
9 Assembly Base 1. Install four casters to the under side of t he base as pictured in Fig. 2. 2. Thread the hex nut (B, Fig. 1) onto the caster shaft. Then slide the lock washer (A, Fig. 1) over the caster shaft. Thread the caster shaft into the threaded hole on the undersi de of the base, turn until snug. Tighten the nut (B, Fig. 1) against the ba ...
-
Jet Tools DC-1100G - page 10
10 Connector Housing 5. Attach three support brac kets (A, Fig. 4) to the base using six M8 x 16 hex cap bolts and six M8 flat washers (B, Fig. 4). Hand-tighten only at this time. 6. Install the housing (A, Fig. 5) to two support brackets (B, Fig. 5) using four M8 x 16 hex cap bolts, eight M8 flat washers, and four M8 hex nuts (C, Fig. 5). Be sure ...
-
Jet Tools DC-1100G - page 11
11 Filter Bag Installation – DC-1100A/RC Referring to Figure 7: 1. Place the hanger (A) on the hanger bracket (B). 2. Slide the filter bag loop (C) over the hanger hook. 3. Thread the re tainer strap (D) through the loops on the filter bag (E) and fasten to the collector housing (F). Collector Bag Installation – DC-1100A/RC Referring to Figure ...
-
Jet Tools DC-1100G - page 12
12 Collector Bag Installation – DC-1100C/RC 1. Place the rin g over the top of the plastic bag an d fold over the bag approximately three inche s, Figure 9. 2. Insert the snap ring (A, Fig. 10) of the collector bag into the bottom of the housing at an angle. 3. Pull down on the ring to make sure it “seats” in the housing. Note: make sure the ...
-
Jet Tools DC-1100G - page 13
13 Electrical Connections All electrical connections must be done by a qualified electrician. All adjustments or repairs must be done with the dust collector disco nnected from the power source, unplugged. Failu re to comply may result in serious injury! The DC-1100A/RC and DC-110 0C/RC dust collectors are rated at 115/230V, Prewired 115V . Use a p ...
-
Jet Tools DC-1100G - page 14
14 Maintenance Never perform maintenance on this machine before turning s witch off and removing plug from power source. Failure to comply may cause serious injury! Cleaning the Filter Bag – DC-1100A/RC Wearing a particle mask or respirator for protection against fine dust particles during cleaning is highly recommended. During first use and afte ...
-
Jet Tools DC-1100G - page 15
15 Parts List – DC -1100A/RC Dust Collector Index No. Part No. Description Size Qty 1 ............... 411035W ................. Impe ller Hous ing ....................................................................... .............................. 1 2 ............... 411026W ................. Motor Bracket ...................................... ...
-
Jet Tools DC-1100G - page 16
16 Parts Breakdown – DC -1100A/RC Dust Collector ...
-
Jet Tools DC-1100G - page 17
17 Filter Assembly for DC-1100C/RC Models Index No. Part No. Description Size Qty 1 ............... 331050..................... Handle .................................................................................................................... 1 2 ............... TS-1540071 ............. Hex Nut ............................................. ...
-
Jet Tools DC-1100G - page 18
18 Remote Control Breakdown for DC-1100RC Index No. Part No. Description Size Qty ................. DC1100RC-100 ....... Receiver Assembly (Ite ms 1-12) ............................................................. ............... 1 1 ............... DCRC-101 ............... Label .................................................................... ...
-
Jet Tools DC-1100G - page 19
19 Wiring Diagram – DC-1100A/C ...
-
Jet Tools DC-1100G - page 20
20 Wiring Diagram – DC-1100RC ...
Jet Tools DC-1100Gについてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもJet Tools DC-1100Gの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがJet Tools DC-1100Gで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。