JL Audio 300/2の取扱説明書

11ページ 0.24 mb
ダウンロード

ページに移動 of 11

Summary
  • JL Audio 300/2 - page 1

    Thank you for purchasing a JL Audio amplifier for your automotive sound system. Your amplifier has been designed and manufactured to exacting standards in or der to ensure years of musical enjoyment in your vehicle. For maximum performance and extended warranty coverage, we highly recommend that you have your new amplifier installed by an authorize ...

  • JL Audio 300/2 - page 2

    PLANNING Y OUR INST ALLA TION It is impor tant that you take the time to read this manual and that you plan out y our installation carefully . The following are some considerations that you m ust take into account when planning your installation. Cooling Efficiency Considerations: Y our JL Audio amplifier emplo ys an advanced type of heat managemen ...

  • JL Audio 300/2 - page 3

    PO WER CONNECTIONS Before installing the amplifier , disconnect the negative (ground) wire from the vehicle's batter y . This will prevent accidental damage to the system, the vehicle and y our body during installation. The 300/2's “+12 VDC” and “Ground” connections are designed to accept 8 - 4 AWG power wire. 8 A WG is the minimu ...

  • JL Audio 300/2 - page 4

    INPUT SECTION The 300/2 has one input section, which contains a pair of RC A-type input jacks, an “Input V oltage” switch and an “Input Sens. ” rotar y control. 1) Input V oltage Range: A wide r ange of signal input voltages can be accommodated by the 300/2's input section (200mV – 8V). This wide range is split up into two sub-r ange ...

  • JL Audio 300/2 - page 5

    PREAMP OUTPUT SECTION The 300/2 incorpor ates a flexible preamp output section, so that additional amplifier s can be added to the system. This pre-amp output can be configured three different ways using the switch labeled “Output Mode” in the “Preamp Output Section” . 1) “Full-Range”: The preamp output delivers the same signal that is ...

  • JL Audio 300/2 - page 6

    SER VICING Y OUR JL AUDIO AMPLIFIER If your amplif ier fails or malfunctions, please return it to your authorized JL Audio dealer so that it may be sent in to JL Audio for ser vice . There are no user ser viceable par ts or fuses inside the amplifier . The unique nature of the circuitr y in the JL Audio amplif iers requires specifically trained ser ...

  • JL Audio 300/2 - page 7

    APPENDIX B: Input Sensitivity Lev el Setting JL Audio amplifier s utilizing the Regulated Intelligent P ow er Supply (R.I.P .S.) allow deliver y of their rated power when connected to any load impedance from 1.5 - 4 Ω per channel (3 - 8 Ω bridged) and when connected to a char ging system with any voltage from 11 - 14.5V . This design is benefic ...

  • JL Audio 300/2 - page 8

    JL AUDIO 300/2 15 “ MY AMPLIFIER TURNS ON, BUT THERE IS NO OUTPUT ” Check the input signal using an A C voltmeter to measure the voltage from the source unit while an appropriate test tone is play ed through the source unit (disconnect the RC A cables from the amplif ier prior to this test). The frequency used should be in the range that is to ...

  • JL Audio 300/2 - page 9

    JL AUDIO 300/2 17 APPENDIX D: 300/2 Specifications GENERAL SPECIFICA TIONS: Recommended Fuse Value: 40A Recommended Fuse T ype: A GU or MaxiFuse™ INPUT SECTIONS: No. of Inputs: One Stereo Pair Input T ype: Differential-balanced with RCA jack inputs Input Range: Switchable from 200mV - 2V RMS to 800mV - 8V RMS AMPLIFIER SECTION: Amplifier T opolog ...

  • JL Audio 300/2 - page 10

    JL AUDIO 300/2 19 18 JL AUDIO 300/2 INST ALLA TION NO TES: Use this diagram to document your amplifier’ s switch and control positions. ...

  • JL Audio 300/2 - page 11

    LIMITED W ARRANTY - AMPLIFIERS (USA) JL AUDIO warr ants this product to be free of defects in materials and wor kmanship for a period of ninety (90) days from the original date of purchase . The warr anty ter m is extended to two (2) y ear s if installation is performed or approved b y an authorized JL AUDIO dealer (proof of installation or appro v ...

メーカー JL Audio カテゴリー Car Stereo System

JL Audio 300/2のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 300/2の取扱説明書
- JL Audioの製品カード
- パンフレット
- またはJL Audio 300/2の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、JL Audio 300/2の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、JL Audio 300/2の取り付け説明書、サービスマニュアル、簡易説明書、またはJL Audio 300/2のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、JL Audio 300/2の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

JL Audio 300/2デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがJL Audio 300/2を使用するのを助ける技術的文書のことです。説明書は通常、全てのJL Audio 300/2ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

JL Audioの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. JL Audio 300/2の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははJL Audio 300/2の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。JL Audio 300/2に関してこのドキュメントで見つけることができる全てのヒントの目次
3. JL Audio 300/2デバイスの基本機能を使うにあたってのヒント。 JL Audio 300/2のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。JL Audio 300/2に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるJL Audio 300/2のメーカー/サービスへの連絡先に関する情報。

JL Audio 300/2についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもJL Audio 300/2の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがJL Audio 300/2で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)