JAI CV-M532の取扱説明書

24ページ 1.35 mb
ダウンロード

ページに移動 of 24

Summary
  • JAI CV-M532 - page 1

    Opera tion Manual Remote Head Monochrome CCD Camera (Rev.E) CV -M532 ...

  • JAI CV-M532 - page 2

    CV -M53 2 DECL ARA TION OF CONFORMIT Y AS D EFINE D B Y T HE C O UNC IL D IREC T IV E 89/336/EEC E MC (E LECTR O MAG N E TIC C OMP A TI B ILITY ) WE HE R E WITH DECLAR E THA T TH IS PRODUCT C OM PLI E S WITH THE FOLL OWI NG PR OVISIONS APPL YI NG T O IT . E N-50081-1 E N-50082-1 ...

  • JAI CV-M532 - page 3

    - 2 - CV -M53 2 T able of Contents T able of Contents .............................................................................................................. ......................... 2 1 . General ................................................................................................................................................ ...

  • JAI CV-M532 - page 4

    - 3 - CV -M53 2 1. General The model CV -M532 is a new remote micro-head camera system featuring virtually identical performance and function of the popular CV -M50 standard machine vision camera. Precisely installed CCD imager (1/3") and miniature size (ø12mm) allows access to very contained spaces. The remote micro-head weights only 5g (0.0 ...

  • JAI CV-M532 - page 5

    - 4 - CV -M53 2 3. Main F eatures • Miniature-sized remote head - ø12mm (0.47") • 1/3" Hyper HAD interline transfer CCD imager , 768(H) x 494(V) for E IA and 752(H) x 582(V) for CCI R • High resolution - horizontal 570 TV lines for EIA • Excellent S/N - better than 56dB • High sensitivity - 0.2 lx minimum illumination on CCD im ...

  • JAI CV-M532 - page 6

    - 5 - CV -M53 2 4. Locations and F unctions 4-1. CCU 4-2. HEAD 1 12P connector : T o connect camera head with camera control unit (For Camera Head) 2 Video output connector : T o output video VS1.0Vp-p (BNC connector) 3 SW1 switch : T o set shutter speed and function modes 4 6-pin Multi connector : Output WEN/EEN signal and input external trigger p ...

  • JAI CV-M532 - page 7

    - 6 - CV -M53 2 5. Pin Assignment 5.1. 12-pin Multi-connector (DC-IN/SYNC.) T ype: HR10A-10R-12PB (Hirose) male Seen from rear. Notes: *1 ) Signals on pin no. 6, 7 and 9 can be changed by jumper setting. See “7.3. Jumper Settings” for more information. *2 ) In Edge Pre-select and Pulse Width Control mode do not input ext. VD signal. 5.2. 6-pin ...

  • JAI CV-M532 - page 8

    - 7 - CV -M53 2 6. F unctions and Operations 6.1. Input/Output of HD/VD Signal 6.1.1. Input of External HD/VD Signal As factory setting the camera can be synchronized by external HD/VD signals. The signal level must be 4.0V p-p +/- 2.0V at the input with the 75 Ohm termination ON. T o change to non-terminated input, see instructions in “7. Mode S ...

  • JAI CV-M532 - page 9

    - 8 - CV -M53 2 T o use this mode Set: SW1-4 to ON for ext. trigger shutter SW1-5 to OFF for field accumulation SW1-6 to ON for non-interlaced SW1-1,2 and 3 to shutter speed Input: Ext. trigger to pin 5 on 6 pin multi connector. Ext. HD to pin 6 on 12-pin multi connector. (If used). 75 Ohm termination is done with SW2-1 (HD) and SW2-2 (ext.trigger) ...

  • JAI CV-M532 - page 10

    - 9 - CV -M53 2 6.3.2. Pulse Width Control Mode The pulse width control mode will only work in non-interlaced field accumulation mode. The exposure is controlled by the low period of the ext. trigger pulse. The exposure starts at the first HD pulse after the falling edge of the ext. trigger pulse. The exposure ends at the first HD pulse after the r ...

  • JAI CV-M532 - page 11

    - 10 - CV -M53 2 Cautions in the Pulse Width Control Mode. 1. Pulse width control mode is effective only in non-interlaced field accumulation mode. 2. The exposure start may be delayed up to 1H max., when the falling edge of ext. trigger pulse is not synchronized with the falling edge of ext. H D signal. T o avoid this 1H jitter and delay, the fall ...

  • JAI CV-M532 - page 12

    - 11 - CV -M53 2 6.3.3. Star t/Stop T rigger Mode The Start /Stop trigger will work in 3 modes: 1. Interlaced with frame accumulation. 2. Interlaced with field accumulation. 3. Non-interlaced with field accumulation. The exposure time is controlled by the interval between the ext. trigger pulse and the ext. VD signal. The exposure starts at the fir ...

  • JAI CV-M532 - page 13

    - 12 - CV -M53 2 Cautions in the Star t/Stop T rigger Mode. 1. The input of ext. VD signal must be given continuously to synchronize with int. VD signal. It is not possible to input ext. VD signal randomly. 2. The exposure start may delay up to 1H max., when the falling edge of ext. trigger pulse is not synchronized with the falling edge of ext. H ...

  • JAI CV-M532 - page 14

    - 13 - CV -M53 2 6.3.4. Long Time Exposure Mode The Long time exposure will work in 3 modes: 1. Interlaced with field accumulation. 2. Interlaced with frame accumulation. 3. Non-interlaced with field accumulation. The exposure time is the interval between 2 ext. VD pulses sent to the camera VD input. Each ext. VD pulse will reset and restart the in ...

  • JAI CV-M532 - page 15

    - 14 - CV -M53 2 Cautions in the Long Time Exposure Mode. 1. Theoretical exposure time is as follows. EIA: 1/30 sec. to ∞ . 2. It is recommended not to use exposure > 2 sec. since visible dark-current noise may occur. 3. Ext. HD signal (4.0 Vp-p ± 2.0V at 75 Ohm terminated) has to be input continuously The falling edge of Int. HD signal and E ...

  • JAI CV-M532 - page 16

    - 15 - CV -M53 2 7. Mode Setting Caution on Mode Setting. Before making any mode or jumper setting turn the po wer OF F . 7.1.1. SW1 Switch on the Rear Panel Factory settings for SW1 are with all 8 switches in OFF position. 7.1.2. T able for SW 1 Setting 7.1.3. T able for Shutter T ime Caution on Shutter . The image can flicker when the illuminatio ...

  • JAI CV-M532 - page 17

    - 16 - CV -M53 2 7.1.4. Ext. T rigger Shutter Mode When trigger select SW1-4 is ON. The camera is in ext. trigger shutter mode. The SW1-1, SW1-2 and SW1- 3 are for selecting the shutter speed. The range is from OFF to 1/10,000 second in 8 steps. For each external trigger pulse, the camera will make an exposure with the selected shutter speed. The s ...

  • JAI CV-M532 - page 18

    - 17 - CV -M53 2 7.3. Jumper Settings Caution on Jumper Setting. Before making any mode or jumper setting turn the po wer OF F . Jumpers for mode setting are found on the boards PK8054 & PK8057. The following modes are available with jumper setting: Input/Output Mode of HD/VD signal. (HD/VD input is factory setting) Edge Pre-select Mode. (Facto ...

  • JAI CV-M532 - page 19

    - 18 - CV -M53 2 7.4. Location of SW2 and Jumpers Jumpers are shorted with a 0 Ohm resistor or by a soldering between the 2 points. T o remove the solder tin from a jumper position, use a special tin remover such as de-soldering wick. 7.4.1. Board PK8054 Side B 7.4.2. Board PK8057 Side A R127 ...

  • JAI CV-M532 - page 20

    - 19 - CV -M53 2 8. Adjustment of Video Signal Output Level When an alignment of a video output signal is required, remove the camera housing and adjust potentiometers VR3, VR4 and VR5 on the PK8056 board while measuring their levels at the video output connector. This adjustment should only be done in a setup with a standard TV test chart and cont ...

  • JAI CV-M532 - page 21

    - 20 - CV -M53 2 9. External Appearance Unit : mm (inches) 9.1 CCU 9.2 HEAD ...

  • JAI CV-M532 - page 22

    - 21 - CV -M53 2 10. Specifications Scanning system EIA 525 lines 30 frames/sec. CCD sensor Monochrome "1/3" Hyper HAD IT CCD Sensing area 4.9 mm ( h) x 3.7 mm ( v) Effective pixels 768 (h) x 494 (v) Elements in video output 758 (h) x 486 (v) Cell size 6.35 (h) x 7.4 (v) µm Resolution (horizontal) 570 TV lines Resolution (vertical) 485 T ...

  • JAI CV-M532 - page 23

    - 22 - CV -M53 2 11. Appendix 11.1. Precautions Personnel not trained in dealing with similar electronic devices should not service this camera. The camera contains components sensitive to electrostatic discharge. The handling of these devices should follow the requirements of electrostatic sensitive components. Do not attempt to disassemble this c ...

  • JAI CV-M532 - page 24

    JAI America, Inc., USA Suite 450 23046 Avenida de la Carlota Laguna Hills, CA 92653 USA Phone +1 949 472 5900 Fax +1 949 472 5908 www.jai.com JAI Corporation, Japan German Industry Center 1-18-2 Hakusan, Midori-ku Y okohama, Kanagawa 226-0006, Japan Phone +81 45 933 5400 Fax +81 45 931 6142 www.jai-corp.co.jp JAI A·S, Denmark Produktionsvej 1, 260 ...

メーカー JAI カテゴリー Security Camera

JAI CV-M532のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- CV-M532の取扱説明書
- JAIの製品カード
- パンフレット
- またはJAI CV-M532の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、JAI CV-M532の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、JAI CV-M532の取り付け説明書、サービスマニュアル、簡易説明書、またはJAI CV-M532のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、JAI CV-M532の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

JAI CV-M532デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがJAI CV-M532を使用するのを助ける技術的文書のことです。説明書は通常、全てのJAI CV-M532ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

JAIの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. JAI CV-M532の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははJAI CV-M532の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。JAI CV-M532に関してこのドキュメントで見つけることができる全てのヒントの目次
3. JAI CV-M532デバイスの基本機能を使うにあたってのヒント。 JAI CV-M532のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。JAI CV-M532に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるJAI CV-M532のメーカー/サービスへの連絡先に関する情報。

JAI CV-M532についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもJAI CV-M532の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがJAI CV-M532で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)