Hampton Direct HI300の取扱説明書

24ページ 1.23 mb
ダウンロード

ページに移動 of 24

Summary
  • Hampton Direct HI300 - page 1

    FPI FIREPLACE PRODUCTS INTERNA TIONAL L TD. 6988 V enture St., Delta, BC Canada, V4G 1H4 918-240e MODEL: HI300 07/18/06 Installer : Please complete the details on the back cover and leave this manual with the homeowner . Homeowner: Please keep these instructions for future reference. T ested by: W ood Cast Insert Owners & Installation Manual ww ...

  • Hampton Direct HI300 - page 2

    Hampton HI300 Wood Cast Insert 2 Thank-you for purchasing a HAMPTON FIREPLACE PRODUCT . The pride of workmanship that goes into each of our products will give you years of trouble-free enjoyment. Should you have any questions about your product that are not covered in this manual, please contact the HAMPTON DEALER in your area. Keep those HAMPTON F ...

  • Hampton Direct HI300 - page 3

    Hampton HI300 Wood Cast Insert 3 T ABLE OF CONTENTS SAFETY LABEL Safety Label For HI300 ................................................. 4 UNIT DIMENSIONS Unit Dimensions ............................................................ 5 INST ALLA TION Before Installing Y our Insert .......................................... 6 Chimney Specifi cations ...

  • Hampton Direct HI300 - page 4

    Hampton HI300 Wood Cast Insert 4 SAFETY LABEL This is a copy of the label that accompanies your Hampton Insert . We have printed a copy of the contents here for your review . NOTE: Hampton units are constantly being improved. Check the label on the unit and if there is a difference, the label on the unit is the correct one. Jan Feb Mar Apr May June ...

  • Hampton Direct HI300 - page 5

    Hampton HI300 Wood Cast Insert 5 UNIT DIMENSIONS 17-1/4” 9” 1 1-1/8” 1 1-3/8” 8-1/2" 21-1/2” 30” 30-7/8" 23-1/4” 23-3/4” 42-1/2” 41” 40” 7-3/4” NOTE: Before assembling your Insert, use these dimensions to ensure appropriate clearances will be met (refer to Masonry and Factory Built Fireplace Clearances section). ...

  • Hampton Direct HI300 - page 6

    Hampton HI300 Wood Cast Insert 6 INST ALLA TION CHIMNEY SPECIFICA TIONS Before installing, check and clean your chimney system thoroughly . If in doubt about its condi- tion, seek professional advice. Y our Hampton Insert is designed for installation into a masonry fi replace that is constructed in accordance with the requirements of "The Sta ...

  • Hampton Direct HI300 - page 7

    Hampton HI300 Wood Cast Insert 7 Clearance Diagram for Installations Side and T op facing is a maximum of 1.5" thick. Floor protection must be non-combustible, insula- tive material with an R value of 1.1 or greater . * Hearth thickness of 0.5" with k value = 0.84", R value = 0.6 or greater . Thermal fl oor protection not required i ...

  • Hampton Direct HI300 - page 8

    Hampton HI300 Wood Cast Insert 8 FLUE CONNECT OR BRACKET Package contains: 3 brackets and 6 screws. These brackets are to be used to hold the fl ue liner (not supplied) to the Insert and keep the connection. The brackets are screwed into the top of the Insert in the pre-punched holes and then screwed into the fl ue liner . INST ALLA TION OPTIONAL ...

  • Hampton Direct HI300 - page 9

    Hampton HI300 Wood Cast Insert 9 1) Positive Flue Connection with Cleanout 2) Direct Flue Connection with Cleanout 3a) Full Flue Liner (No Cleanout Required) Note: A clean-out door is sometimes required, by your inspector , to be installed when either the Positive fl ue connection or Direct fl ue connection method is used. The use of one of the c ...

  • Hampton Direct HI300 - page 10

    Hampton HI300 Wood Cast Insert 10 INST ALLA TION CAST F ACEPLA TE INST ALLA TION 3) Place Mantel T op onto the top of the fi rebox. Mantel T op 2) Secure the Left and Right Side Faceplate to the fi rebox by aligning the Mounting Holes with the Side Mounting Brackets taking care to align vertically while each side rests on the hearth. Secure using ...

  • Hampton Direct HI300 - page 11

    Hampton HI300 Wood Cast Insert 11 5) Mount the T op Faceplate by carefully sliding the Mounting Plates on the Left and Right Side Faceplate thru the Retainers in the T op Faceplate. NOTE: Slowly lower the T op Faceplate into position; being careful not to damage the Mantel T op. 7) Location of Insulations a) Place 1 piece of Insulation behind the M ...

  • Hampton Direct HI300 - page 12

    Hampton HI300 Wood Cast Insert 12 Backside of Fan Facia Shown. Y our fan should only be installed once the unit is in place in order to prevent any damage to the fan. 1) Attach the Left and Right Side Fan Facia to the Front Fan Facia by aligning the Side Facia screw slots with the hole locations in the Front Fan Facia and secure using 2 screws per ...

  • Hampton Direct HI300 - page 13

    Hampton HI300 Wood Cast Insert 13 Pull Open Push Closed hand side, as far as possible and then bring it back into the hole on the right hand side. Use a pair of vise grips or pliers and tap it into place with a hammer . A tighter fi t will ensure the tube will not move when the unit is burning. Though there are four air tubes in the medium units. ...

  • Hampton Direct HI300 - page 14

    Hampton HI300 Wood Cast Insert 14 9) During the fi rst few hours it may be more diffi cult to start the fi re. As you dry out your fi re brick and your masonry fl ue (if applicable), your draft will increase. 10) For those units installed at higher elevations or into sub-standard masonry fi replaces, drafting problems may occur . Consult an e ...

  • Hampton Direct HI300 - page 15

    Hampton HI300 Wood Cast Insert 15 ASH DISPOSAL During constant use, ashes should be removed every few days. Please take care to prevent the build-up of ash around the start-up air housing located inside the fi rebox, under the loading door lip. DO NOT ALLOW ASHES TO BUILD UP TO THE LOADING DOORS. Only remove ashes when the fi re has died down. Ev ...

  • Hampton Direct HI300 - page 16

    Hampton HI300 Wood Cast Insert 16 DOOR GASKET If the door gasket requires replacement, 7/8" diameter material must be used. A proper high temperature gasket adhesive is required. A gasket repair kit, Part # 846-570 is available from your local Hampton dealer . GLASS CLEANING Only clean your glass window when it is cool. Y our local retailer ca ...

  • Hampton Direct HI300 - page 17

    Hampton HI300 Wood Cast Insert 17 LA TCH ADJUSTMENT The door latch may require adjustment as the door gasket material compresses after a few fi res. Removal of spacers will allow the latch to be moved closer to the door frame, causing a tighter seal. 1) Remove the Latch Assembly from the unit by undoing the outer 2 bolts. 2) Remove the Latch from ...

  • Hampton Direct HI300 - page 18

    Hampton HI300 Wood Cast Insert 18 HI300 MAIN ASSEMBL Y Part # Description 1) 942-681* Right Side Cast 936-238 Side Cast Gasket 2) 300-021 Flange Adaptor 3) 942-691* Ashlip 4) 300-006 Fan Clip 5) 300-023 Door Latch Bracket 6) 942-671* Left Side Cast 936-238 Side Cast Gasket Part # Description 8) 942-661* Mantel T op 15) 300-91 1* Fan Assembly 20) 50 ...

  • Hampton Direct HI300 - page 19

    Hampton HI300 Wood Cast Insert 19 HI300 CAST F ACEPLA TE Part # Description 300-921 Cast Faceplate - Metallic Black 300-925 Cast Faceplate - T imberline Brown 300-926 Cast Faceplate - Enamel Black 200) 942-651* T op Faceplate 201) 942-71 1* Left Side Faceplate 202) 942-701* Right Side Faceplate * Last digit of part number represents color: 1 = Meta ...

  • Hampton Direct HI300 - page 20

    Hampton HI300 Wood Cast Insert 20 P ARTS LIST HI300 BRICK P ANELS Part # Description 180-960 Brick Set - Complete ...

  • Hampton Direct HI300 - page 21

    Hampton HI300 Wood Cast Insert 21 NOTES ...

  • Hampton Direct HI300 - page 22

    Hampton HI300 Wood Cast Insert 22 NOTES ...

  • Hampton Direct HI300 - page 23

    Hampton HI300 Wood Cast Insert 23 W ARRANTY Hampton Fireplace Products are designed with reliability and simplicity in mind. In addition, our internal Quality Assurance T eam carefully inspects each unit thoroughly before it leaves our facility . FPI Fireplace Products International Ltd. is pleased to extend this limite d lifetime warranty to the o ...

  • Hampton Direct HI300 - page 24

    Printed in Canada Installer: Please complete the following information Dealer Name & Address: ______________________________________________ ___________________________________________________________________ Installer: ___________________________________________________________ Phone #: _________________________________________________________ ...

メーカー Hampton Direct カテゴリー Fire Pit

Hampton Direct HI300のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- HI300の取扱説明書
- Hampton Directの製品カード
- パンフレット
- またはHampton Direct HI300の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Hampton Direct HI300の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Hampton Direct HI300の取り付け説明書、サービスマニュアル、簡易説明書、またはHampton Direct HI300のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Hampton Direct HI300の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Hampton Direct HI300デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがHampton Direct HI300を使用するのを助ける技術的文書のことです。説明書は通常、全てのHampton Direct HI300ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Hampton Directの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Hampton Direct HI300の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははHampton Direct HI300の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Hampton Direct HI300に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Hampton Direct HI300デバイスの基本機能を使うにあたってのヒント。 Hampton Direct HI300のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Hampton Direct HI300に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるHampton Direct HI300のメーカー/サービスへの連絡先に関する情報。

Hampton Direct HI300についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもHampton Direct HI300の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHampton Direct HI300で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)