-
Honeywell PRO TH3210D - page 1
Installation Guide TH3210D Non-programmable Digital Thermostat ...
-
Honeywell PRO TH3210D - page 2
Product Application This thermostat provides electronic control of 24 V A C heat pump systems with aux- iliar y heat (2 heat/1 cool). Power T ype • Batter y power • Common wire • Common wire with batter y backup System Settings • Heat, Off, Cool, Em Heat Fan Settings • A uto, On Must be installed by a trained, experienced technician • R ...
-
Honeywell PRO TH3210D - page 3
PRO TH3210D Non-programmable Digital Thermostat 1 Install the thermostat about 5 feet (1.5m) above the floor in an area with good air circulation at average temperatur e. Do not install in locations where the thermostat can be af fected by: • Drafts or dead spots behind doors and in corners • Hot or cold air from ducts • Sunlight or radiant h ...
-
Honeywell PRO TH3210D - page 4
Installation Guide 2 Pre-installation checklist Package contents Check to make sure y our package includes the f ollowing items: • PR O TH3210D digital thermostat (wallplate attached to back) • Operating manual • W all anchors and mounting screws (2 each) • AA alkaline batteries (2) Required tools & supplies • No. 2 Phillips screwdriv ...
-
Honeywell PRO TH3210D - page 5
PRO TH3210D Non-programmable Digital Thermostat 3 Remove the w allplate from the ther- mostat as shown at left, then f ollow directions below f or mounting. 1 Pull wires through wire hole. 2 P osition wallplate on wall, level and mark hole positions with pencil. 3 Drill holes at marked positions as shown below , then tap in supplied wall anchors. 4 ...
-
Honeywell PRO TH3210D - page 6
Installation Guide 4 Wiring 1 Loosen screw terminals, insert wires into terminal block, then re- tighten screws. 2 Push e xcess wire back into the wall opening. K eep wires in shaded area as shown at left. 3 Plug the wall opening with non- f lamma ble insulation to pr event drafts from affecting thermostat operation. T erminal Designations E E Emer ...
-
Honeywell PRO TH3210D - page 7
PRO TH3210D Non-programmable Digital Thermostat 5 1 Power supply . Provide disconnect means and overload pr otection as required. 2 Optional 24 V AC common connection. 3 Use either O or B terminals for changeover valve. 4 L terminal is powered continuously when thermostat is set to Em Heat. 5 Install field jumper between E and Aux if there is no em ...
-
Honeywell PRO TH3210D - page 8
Installation Guide 6 AC Power The thermostat can be powered by 24 V A C power , or by batter ies. T o wire the thermostat for AC po wer , connect the common side of the transf or mer to the “C” terminal as shown at left. Connect common side of transformer to “C” terminal Install batteries in back of thermostat (optional if AC powered). Batt ...
-
Honeywell PRO TH3210D - page 9
PRO TH3210D Non-programmable Digital Thermostat 7 6 5 6 8 9 14 15 Auxiliary heat cycle rate (CPH) Emergency heat cycle rate (CPH) Compressor cycle rate (CPH) T emperature display Compressor protection 5 For gas or oil furnaces of less than 90% efficiency 1 For steam or gravity systems 3 For hot water systems & furnaces of over 90% efficiency 9 ...
-
Honeywell PRO TH3210D - page 10
Installation Guide 8 10 0 T est 10 20 30 70 Heating system Emergency heat Cooling system Thermostat information (for refer ence only) 0 Compressor and fan turn off. 1 Compressor and fan turn on. 2 Auxiliary heat turns on. 0 Heat and fan turn off. 1 Heat and fan turn on. 2 Auxiliary heat turns on. 0 Compressor and fan turn off. 1 Compressor and fan ...
-
Honeywell PRO TH3210D - page 11
PRO TH3210D Non-programmable Digital Thermostat 9 Inside Set T o 75 75 Em Aux Heat On ° ° Replace Batt Quick refer ence to display screen Current inside temperatur e Low battery warning T emperature setting System status Em: Emergency heat on Aux: Auxiliary heat on Heat On/Cool On: (Flashes when waiting for compressor r estart) Quick refer ence t ...
-
Honeywell PRO TH3210D - page 12
Installation Guide 10 In case of difficulty If you hav e dif ficulty with your thermostat, please tr y the sugg estions below . Most problems can be corrected quickl y and easily . Display is blank • Check circuit br eaker and reset if necessary . • Make sure heating & cooling power switches ar e on. • Make sure equipment door is secur el ...
-
Honeywell PRO TH3210D - page 13
PRO TH3210D Non-programmable Digital Thermostat 11 Accessories Please contact your distributor to order accessories. Cover plate assembly ............................................Part Number 50002883-001 (Used to cover marks left by old thermostats.) Specifications T emperature Ranges • Heat: 40° to 90°F (4.5° to 32°C) • Cool: 50° to 99 ...
-
Honeywell PRO TH3210D - page 14
...
-
Honeywell PRO TH3210D - page 15
...
-
Honeywell PRO TH3210D - page 16
Honeywell International Inc. 1985 Douglas Drive North Golden V alley , MN 55422 http://yourhome.honeywell.com Automation and Control Solutions Printed in U.S.A. on recycled paper containing at least 10% post-consumer paper fibers. ® U.S. Registered T rademark. © 2005 Honeywell International Inc. Patents pending. All rights reserved. 69-1775 • 0 ...
Honeywell PRO TH3210Dについてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもHoneywell PRO TH3210Dの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHoneywell PRO TH3210Dで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。