Shure SCM810AZの取扱説明書

17ページ 1.21 mb
ダウンロード

ページに移動 of 17

Summary
  • Shure SCM810AZ - page 1

    User Guide © 200 8 Shure Incorporated 27A8868 (Rev . 2 ) Printed in U.S.A. SCM810/SCM810AZ SCM810/SCM810AZ EIGHT-CHANNEL MICROPHONE MIXER EIGHT-CHANNEL MICROPHONE MIXER SCM810/SCM810C SCM810/SCM810C SCM810/SCM810J SCM810/SCM810J チ チ ャ ャ ン ン ネ ネ ル ル ・ ・ マ マ イ イ ク ク ロ ロ ホ ホ ン ン ミ ミ キ キ サ サ ...

  • Shure SCM810AZ - page 2

    2 DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 SYSTEM FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 OPERATING PRINC IPLES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Shure SCM810AZ - page 3

    3 DESCRIPTION The Shure Model SCM810/E is an eight-channel automatic microphone mixer designed for use in sound re inforcement, audio recording, and broadcast applications. The SCM810 dr amatically improve s audio quality in any application w here multiple microphones are re quired. Any low-im- pedance dynamic or condenser microphone (including wir ...

  • Shure SCM810AZ - page 4

    4 FRONT PANEL FEATURES MODEL SCM810 FRONT PANEL FIGURE 1  Microphone Channel Gain Controls 1–8: Allows adjustment of microphone gain.  Input LED 1–8: Lights green when channel is active; lights red at 6 dB below clipping level.  Low-Cut Filter 1–8: Recessed screwdriver adjustment provides adjustable low-frequency rolloff (h igh pa ss ...

  • Shure SCM810AZ - page 5

    5 DIP SWITCHES The rear-panel DIP switch provides the following setup options. The posi- tions shown in bold type are the factory settings. NOTE: Switch positions and effects are shown in Figure 3 and a lso on the mixer label. MODIFIABLE FUNCTION SWITCHES FIGURE 3 DIP SWITCH SW702 FUNCTIONS Manual/Auto: Automatic activation is defeated in the Manua ...

  • Shure SCM810AZ - page 6

    6 INSTALLATION AND SYSTEM SETUP RACK MOUNTING THE MIXER T o mount the SCM810 in a st and ard 483 mm (19-inch) audio equipment rack, slide the mixer into the rack and secure it with the supplied Phillips head screws, as shown in Figure 4. Use all four screws. RACK MOUNTING THE SCM810/E FIGURE 4 SCM810/E CONNECTIONS Make audio connections as follows ...

  • Shure SCM810AZ - page 7

    7 EQUALIZER FUNCTIONS Low Cut Filter (High-Pass) The low-cut (or high -pass) filter allo ws all frequencies above its cutoff point to pass from filter input to filter output without attenuation, while fr equencies below the cutoff are attenuated (see Figure 6). The cutoff point is defined as the frequency where the signal has dropped 3 dB relative ...

  • Shure SCM810AZ - page 8

    8 NETWORKING MULTIPLE MIXERS If additional inputs are needed, more SCM810 mixers (as many as 50) can be “linked” using supplied link cables. Such a conf iguration can provide up to 400 microphone inputs. T o link multiple mixers, connect the LINK OUT of the first mixer to the LINK IN of the next mixer , and so on (see Figure 8). Leave the LINK ...

  • Shure SCM810AZ - page 9

    9 SPECIFICATIONS Measurement Conditions (unless ot herwise specified): Line voltage 120 V ac, 60 Hz (SCM810) or 230 Vac, 50 Hz (SCM810E); full gain; 1 kHz, one channel activated; source impedances: Mic 150 Ω , Line 150 Ω ; termina- tions: Line 10 k Ω , Phones 300 Ω ( tip- sle eve and ring-sleeve), Direct Out 10 k Ω ; Auto mode, equalization co ...

  • Shure SCM810AZ - page 10

    10 ADVANCED FUNCTIONS LOGIC CONNECTION SPECIFICATIONS The logic functions of the SCM810 ex pand the mixer's range of inst allation and control options. Logic can be used for everything from simple cough switches to elaborate computer-c ontrolled room systems. (Shure's AMS Update publication contains additional appl ications of advanced lo ...

  • Shure SCM810AZ - page 11

    11 SUGGESTED LOGIC APPLICATIONS This section contains suggestions on t he uses of the SCM810's logic capa- bilities. Note that uses of these func tions are not limited to the listed appli- cations. The user is limited only by individual imagination and creativity . For additional suggestions and solutions to installation problems, contact Shur ...

  • Shure SCM810AZ - page 12

    12 Inhibiting Gating for Unwa nted Sounds As described in the Operating Principles section, MaxBus attempts to acti- vate only one microphone per sound source. Muting a microphone channel prevents its audio from appearing at the mixer's output. However , the mut- ed microphone still communicates with other mic channels via MaxBus. A sound sour ...

  • Shure SCM810AZ - page 13

    13 Diode Isolation of Logic Controls T wo or more control functions using the same logic pins can be isolated with diodes. In this manner a chann el can be muted by an overall group mute switch, or by its own cough button (see Figure 19-Channels 1, 3 and 5 modified). DIODE ISOLATION OF LOGIC CONTROLS FIGURE 19 External Logic Devices SCM810 logic le ...

  • Shure SCM810AZ - page 14

    14 INTERNAL MODIFICATIONS W ARNING: All modifications must be performed by qualified service tech- nicians. This section describes SCM810 modifi cations that can be made using sol- der “jumpers” on the printed circuit board; the pads where jumpers may be used are placed close together so that a single solder drop functions as a jumper . Note to ...

  • Shure SCM810AZ - page 15

    15 SCM810 Speech Gate for Mixing Console The SCM810 can be used in conjunction with large mixing consoles to pro- vide automatic mixing for talk shows, panel discussions, and news shows. Large consoles have channel insert jac ks so that e xternal signal process- ing devices can be patched into individual channel si gnal paths. With this modificatio ...

  • Shure SCM810AZ - page 16

    16 Increase Hold Time In addition to the dip switch SW702 options of 0.4- and 1.0-second hold time, the hold time can be increased to 1.5 seconds. (Mor e than 1.5 sec- onds is not recommended.) Procedure: Install a 470 k Ω resistor across jumper points X902. Move DIP switch down to 1.0-second position. Decrease Hold Time The hold time can be decre ...

  • Shure SCM810AZ - page 17

    SHURE Incorporated http://ww w.shure.com United States, Canada, Latin America, Caribbean: 5800 W. Touhy Avenue, Niles, IL 607 14-4608, U.S.A. Phone: 847-600-2000 U.S. Fax: 847-600-1212 Intl Fax: 847-600-644 6 Europe, Middle East, Africa: Shure Europe GmbH, Phone: 49-7131-72140 Fax: 49-7131-721414 Asia, Pacific: Shure Asia Limited, Phone: 852-2893-4 ...

メーカー Shure カテゴリー Mixer

Shure SCM810AZのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- SCM810AZの取扱説明書
- Shureの製品カード
- パンフレット
- またはShure SCM810AZの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Shure SCM810AZの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Shure SCM810AZの取り付け説明書、サービスマニュアル、簡易説明書、またはShure SCM810AZのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Shure SCM810AZの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Shure SCM810AZデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがShure SCM810AZを使用するのを助ける技術的文書のことです。説明書は通常、全てのShure SCM810AZユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Shureの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Shure SCM810AZの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははShure SCM810AZの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Shure SCM810AZに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Shure SCM810AZデバイスの基本機能を使うにあたってのヒント。 Shure SCM810AZのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Shure SCM810AZに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるShure SCM810AZのメーカー/サービスへの連絡先に関する情報。

Shure SCM810AZについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもShure SCM810AZの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがShure SCM810AZで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)