-
Chicago Electric 45338 - page 1
HAMMER DRILL - 1/2 INCH V ARIABLE SPEED - REVERSIBLE 45338 SET UP AND OPERA TING INSTRUCTIONS Distributed exclusively by Harbor Freight T ools ® . 3491 Mission Oaks Blvd., Camarillo, CA 9301 1 Visit our website at: http://www .harborfreight.com Read this material before using this product. Failure to do so can result in serious injury . SA VE THIS ...
-
Chicago Electric 45338 - page 2
SKU 45338 For technical questions, please call 1-800-444-3353. Page 2 SA VE THIS MANUAL Keep this manual for the safety warn- ings and precautions, assembly , operat- ing, inspection, maintenance and cleaning procedures. Write the product’ s serial number in the back of the manual near the assembly diagram (or month and year of purchase if produc ...
-
Chicago Electric 45338 - page 3
SKU 45338 For technical questions, please call 1-800-444-3353. Page 3 plugs with grounded power tools. Unmodied plugs and matching out - lets will reduce risk of electric shock. A void body contact with grounded b. surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded. ...
-
Chicago Electric 45338 - page 4
SKU 45338 For technical questions, please call 1-800-444-3353. Page 4 proved for the specic hazards in the work area. Power tool use and care 4. Do not force the power tool. Use a. the correct power tool for your ap- plication. The correct power tool will do the job better and safer at the rate for which it was designed. Do not use the power too ...
-
Chicago Electric 45338 - page 5
SKU 45338 For technical questions, please call 1-800-444-3353. Page 5 parts can grab the surface and pull the tool out of your control. When using a handheld power tool, 7. maintain a rm grip on the tool with both hands to resist starting torque. Do not leave the tool unattended 8. when it is plugged into an electrical outlet. T urn off the tool ...
-
Chicago Electric 45338 - page 6
SKU 45338 For technical questions, please call 1-800-444-3353. Page 6 who have impaired blood circulation to the hand, past hand injuries, ner- vous system disorders, diabetes, or Raynaud’s Disease should not use this tool. If you feel any symptoms related to vibration (such as tingling, numbness, and white or blue ngers), seek medical advice ...
-
Chicago Electric 45338 - page 7
SKU 45338 For technical questions, please call 1-800-444-3353. Page 7 of electric shock. (See 3-Prong Plug and Outlet.) The grounding prong in the plug is 2. connected through the green wire in- side the cord to the grounding system in the tool. The green wire in the cord must be the only wire connected to the tool’s grounding system and must nev ...
-
Chicago Electric 45338 - page 8
SKU 45338 For technical questions, please call 1-800-444-3353. Page 8 dition. Always replace a damaged extension cord or have it repaired by a qualied electrician before using it. Protect the extension cords from 8. sharp objects, excessive heat, and damp or wet areas. RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS* (120/240 VOL T) NAMEPLA T ...
-
Chicago Electric 45338 - page 9
SKU 45338 For technical questions, please call 1-800-444-3353. Page 9 SPECIFICA TIONS Electrical Requirements 120 V~ / 60 Hz / 6.3 A Motor No Load Speed 0-2800 RPM Chuck Capacity 3/64 to 1/2”, plus key chuck Chuck Thread 1/2" - 20 UNF E194601 UNP ACKING When unpacking, make sure that the item is intact and undamaged. If any parts are missing ...
-
Chicago Electric 45338 - page 10
SKU 45338 For technical questions, please call 1-800-444-3353. Page 10 T ool Set Up TO PREVENT SERIOUS INJUR Y FROM ACCIDENT AL OPERA TION: T urn the Power Switch of the tool to its “OFF” position and unplug the tool from its electrical outlet before performing any inspection, maintenance, or cleaning procedures. The Hammer Drill is equipped wi ...
-
Chicago Electric 45338 - page 11
SKU 45338 For technical questions, please call 1-800-444-3353. Page 1 1 Gear Setting Control Figure F (top view) 6. On the top of the Hammer Drill, push the Gear Setting Control to select plain drilling or hammer drilling. A symbol for a drill bit indicates plain drilling is selected. If a hammer is shown, it is set for hammer drilling. See Figure ...
-
Chicago Electric 45338 - page 12
SKU 45338 For technical questions, please call 1-800-444-3353. Page 12 MAINTENANCE AND SER VICING Procedures not specically explained in this manual must be performed only by a qualied technician. TO PREVENT SERIOUS INJUR Y FROM ACCIDENT AL OPERA TION: T urn the Power Switch of the tool to its “OFF” position and unplug the tool from its e ...
-
Chicago Electric 45338 - page 13
SKU 45338 For technical questions, please call 1-800-444-3353. Page 13 P ARTS LIST Part Description Qty . 1 Screw , M6x25 1 2 Chuck 1 3 Chuck Key 1 4 Spindle 1 5 Steel Ball, 3 1 6 Circle Seal 1 7 Ball Bearing 1 8 Spring 1 9 Gear , Large 1 10 Needle Bearing, HK1207 1 11 Ratchet 1 12 Bearing Holder 1 13 W asher 1 14 Steel Ball 1 15 Ball Bearing, 6290 ...
-
Chicago Electric 45338 - page 14
SKU 45338 For technical questions, please call 1-800-444-3353. Page 14 Record Product’ s Serial Number Here: Note: If product has no serial number , record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only , and are not avail- able individually as replacement parts. ASSEMBL Y DIAGRAM ...
-
Chicago Electric 45338 - page 15
SKU 45338 For technical questions, please call 1-800-444-3353. Page 15 LIMITED 90 DA Y W ARRANTY Harbor Freight T ools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this prod- uct is free from defects in materials and workmanship for the period of 90 days f ...
Chicago Electric 45338についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもChicago Electric 45338の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがChicago Electric 45338で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。