Cisco Systems IE 3000の取扱説明書

32ページ 1.85 mb
ダウンロード

ページに移動 of 32

Summary
  • Cisco Systems IE 3000 - page 1

    1 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Cisco IE 3000 Switch Getting Started Guide • About This Guide, page 1 • T aking Out Wh at Y ou Need, page 2 • Connecting Expansion Modul es, page 3 • Running Express Setup, page 5 • Managing the S witch, page 9 • Installing the Swit ch, page 11 • Connecting to the Switch Ports, ...

  • Cisco Systems IE 3000 - page 2

    Cisco IE 3000 Switch Getting Started Guide 2 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 For additi onal installatio n and conf iguration i nformation for Cisco IE 30 00 switches, see the Cisco IE 3000 docume ntation on Cisco.com. For system requirements, important not es, limitations, open and r esolved bugs, and last-minute documentati ...

  • Cisco Systems IE 3000 - page 3

    3 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Cisco IE 3000 Switch Getting Started Guide Figure 1 Cisco IE 30 0 0 Shipping Bo x Contents Connecting Expansion Modules The switch can operate as a standalone device with Fast Ethernet ports. Y ou can increase the number of Fast Ethern et ports by connecting the Cisco IEM-3000-8TM or the Cisc ...

  • Cisco Systems IE 3000 - page 4

    Cisco IE 3000 Switch Getting Started Guide 4 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Follo w these steps to connect the e xpansion modules to the switch. Step 1 Remov e the right side panel b y firmly grasping both sides in th e middle and pulling it outward. If necessary , use a flat-blade scre wdri ver t o pry open the side panel. ...

  • Cisco Systems IE 3000 - page 5

    5 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Cisco IE 3000 Switch Getting Started Guide Running Express Setup When you f i rst set up the switch, yo u should use Express Setup to ent e r the initial IP information. Doing this enabl es the switch to connect t o local routers and th e Internet. Y ou can then access t he switch through the ...

  • Cisco Systems IE 3000 - page 6

    Cisco IE 3000 Switch Getting Started Guide 6 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 T o run Express Setup: Step 1 Make sure that nothing is con n ected to the switch. During Express Setup, the switch acts as a DHCP server . If your PC has a static IP address, change your PC settings befo re you begin to temporarily use DHCP . Step 2 ...

  • Cisco Systems IE 3000 - page 7

    7 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Cisco IE 3000 Switch Getting Started Guide Step 6 Connect a Cat egory 5 Ethernet cabl e (not provid ed) from the blinking switch port to th e Ethernet port on your PC. The port LEDs on your PC and the swi tch blink green wh ile the sw itch configures the connection. Step 7 When the Setup LED ...

  • Cisco Systems IE 3000 - page 8

    Cisco IE 3000 Switch Getting Started Guide 8 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Step 9 Enter the netw ork settings. All ent ries must be in English letter s and Arabic numbers. • Management Interface (VLAN ) : W e recommend using the def ault, VLAN 1 . The management VLAN establish es an IP connection to the switch. • IP Ass ...

  • Cisco Systems IE 3000 - page 9

    9 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Cisco IE 3000 Switch Getting Started Guide Refreshing the PC IP Address After you complete Express Setup, you sho u ld refresh the PC IP address: • For a dynamically assigned IP address, disconnect th e PC from the switch, and reconnect the PC to the netwo rk. The network DHCP ser ver assig ...

  • Cisco Systems IE 3000 - page 10

    Cisco IE 3000 Switch Getting Started Guide 10 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 3. Use the de vice manager to perform basic switch configur ation and monitoring. See the de vice manager online help for more information. 4. For more adv anced configuration, download and run the Cisco Network Assistant, which is described in the ...

  • Cisco Systems IE 3000 - page 11

    11 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Cisco IE 3000 Switch Getting Started Guide Using the Switch Console Port: Follo w these steps: 1. Connect the supplied RJ- 45-to-DB-9 ad apter cable (conso le cable) to the standard 9-pin serial port on the PC. Connect the ot her end of the cable to the console port on the switch. 2. Start a ...

  • Cisco Systems IE 3000 - page 12

    Cisco IE 3000 Switch Getting Started Guide 12 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 • Attaching the Po wer and Relay Connector , page 20 • Optional Procedures, page 21 Equipment That You Supply Obtain these necessary tools and equipment: • Ratcheting torqu e flathead scre wdriv er that exerts up to 15-inch pound (in-lb ) of p ...

  • Cisco Systems IE 3000 - page 13

    13 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Cisco IE 3000 Switch Getting Started Guide • Airflo w around the switch and throu g h the v ents is unrestricted. T o prev ent the switch from overheating, thes e must be the minimum clearances: – T op and bottom: 4.13 in . (105 mm) – Left and right: 3.54 in. (9 0 mm) – Front: 2.56 i ...

  • Cisco Systems IE 3000 - page 14

    Cisco IE 3000 Switch Getting Started Guide 14 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 War ni ng This unit is intend ed for installation in restricted acc ess areas. A restricted access area can be ac cessed only through the use of a special tool, lock and key , or other means of security . Statement 1017 War ni ng This equipment must ...

  • Cisco Systems IE 3000 - page 15

    15 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Cisco IE 3000 Switch Getting Started Guide War ni ng When used in a Class I, Division 2, haza rdous location, this equipment must be mounted in a suitable enclosure with proper wiring method, for all power , input and output wiring, that com plies with the governing electrical codes and in a ...

  • Cisco Systems IE 3000 - page 16

    Cisco IE 3000 Switch Getting Started Guide 16 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Mounting the Switch to a DIN Rail or to the Rack Adapter Follo w these steps to mount the switch on a DIN r a il or in a rack. Step 1 If you are mountin g th e s witch in a rack, first secure the Cisco IE 3000 rack adapter to the ra ck. If mounting ...

  • Cisco Systems IE 3000 - page 17

    17 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Cisco IE 3000 Switch Getting Started Guide Grounding the Switch Follo w these steps to connect the switch to a protectiv e ground. War ni ng This equipment must be grounded. Never defeat t he ground conductor or operate the equipment in the absence of a suitably installed ground conductor . ...

  • Cisco Systems IE 3000 - page 18

    Cisco IE 3000 Switch Getting Started Guide 18 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Wiring the DC Power Source Follo w these steps to prepare the DC power cable. War ni ng Before performing any of the following procedures, ensure that power is removed from the DC circ uit. Statement 1003 Step 3 Insert the grou nd wire into the ring ...

  • Cisco Systems IE 3000 - page 19

    19 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Cisco IE 3000 Switch Getting Started Guide War ni ng This product relies on the building’ s installation for short-circuit (overcurrent ) protection. Ensure that the protective device is rated not greater tha n: 5A. Statement 1005 War ni ng Only trained and qualified pe rsonnel should be a ...

  • Cisco Systems IE 3000 - page 20

    Cisco IE 3000 Switch Getting Started Guide 20 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Attaching the Power and Relay Connector Follo w these steps to connect the DC po wer and relay connector to the sw itch: Caution The input voltage source of the alarm circ uits must be an isolated source and limited to less t han or equal to 30 VDC, ...

  • Cisco Systems IE 3000 - page 21

    21 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Cisco IE 3000 Switch Getting Started Guide Optional Procedures For detailed inst ructions on these proc edures, see the Cisco IE 3000 Switch H a rd w a re I n s t a l l a t i o n G u i d e on Cisco.co m. • W iring the e xternal alar m relays • Connecting the switch t o the optional PWR-I ...

  • Cisco Systems IE 3000 - page 22

    Cisco IE 3000 Switch Getting Started Guide 22 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Connecting to 10/100 and 10/100/1000 Ports Follo w these steps: For simpli fied cabling, the automatic medium-dependent interf ace crossover (auto-MDIX) feature is en abled by default on the swit ch. W ith auto-MDIX enabled, the switch dete cts the ...

  • Cisco Systems IE 3000 - page 23

    23 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Cisco IE 3000 Switch Getting Started Guide Installing SFP Modules and Connecting to Ports Follo w these steps: For a list of su pported modules, see the release not es on Cisco.com. Fo r detailed instructions on installing, remo ving, and connecting to SFP modules, see the documentation that ...

  • Cisco Systems IE 3000 - page 24

    Cisco IE 3000 Switch Getting Started Guide 24 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Connecting to Dual-Purpose Ports Only one port on a dual -purpose port can be acti ve at a time. If b oth ports are connected, the SFP modu le port has priority . Follo w these steps: Connecting to 100BASE-FX Ports Follo w these steps: Verifying Por ...

  • Cisco Systems IE 3000 - page 25

    25 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Cisco IE 3000 Switch Getting Started Guide In Case of Difficulty See these sections if you ha ve dif ficulty setting up your swit ch: • T roubleshooting Express Setup, page 25 • Resetting the Switch, page 26 • Accessing Online Help, page 2 7 • For More Informat ion, page 27 Troublesh ...

  • Cisco Systems IE 3000 - page 26

    Cisco IE 3000 Switch Getting Started Guide 26 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Resetting the Switch Follo w these steps to return your switch to the factory default settings. These are reasons why you might w ant to reset the switch: • Y ou installed the switch in your networ k and cannot connect to it because you assigned t ...

  • Cisco Systems IE 3000 - page 27

    27 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Cisco IE 3000 Switch Getting Started Guide Accessing Online Help First look for a soluti on to your problem in th e troubleshooting section of the switch hardware i nstallation guide or the switch softw are configuration guid e on Cisco.com. Y ou can also access the Cisc o T e chnical Suppor ...

  • Cisco Systems IE 3000 - page 28

    Cisco IE 3000 Switch Getting Started Guide 28 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Obtaining Documentation and Submitting a Service Request For informatio n on obtaining documentation, submitting a service request, and gathering additio nal information, see the monthl y What’ s New in Cisco Pr oduct Documentation , which also li ...

  • Cisco Systems IE 3000 - page 29

    29 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Cisco IE 3000 Switch Getting Started Guide Note Y ou must have Adobe Acrobat R eader to view and print PDF files. Y ou can do wnload the reader from Adobe’ s website: http://www .adobe.com 3. T o read translated and localized warrant y information ab out your product, follo w these steps: ...

  • Cisco Systems IE 3000 - page 30

    Cisco IE 3000 Switch Getting Started Guide 30 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 To Receive a Return Materials Authorization (RMA) Number Contact the compan y from whom you purc hased the product. If you purchased the product directly from Cisco, contact your Cisco Sales and Service Representativ e. Complete the information belo ...

  • Cisco Systems IE 3000 - page 31

    31 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Cisco IE 3000 Switch Getting Started Guide ...

  • Cisco Systems IE 3000 - page 32

    Cisco IE 3000 Switch Getting Started Guide 32 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 CCDE, CCENT, Cisco Eos , Cisco Lumin, Cisco StadiumVision, the Ci sco logo, DCE, and Welcome to the Human Network are trademarks; Changing the Way We Work, Live, Pl ay, and Learn is a service mark; and Access Registrar, Aironet, As yncOS, Bringi ng ...

メーカー Cisco Systems カテゴリー Switch

Cisco Systems IE 3000のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- IE 3000の取扱説明書
- Cisco Systemsの製品カード
- パンフレット
- またはCisco Systems IE 3000の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Cisco Systems IE 3000の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Cisco Systems IE 3000の取り付け説明書、サービスマニュアル、簡易説明書、またはCisco Systems IE 3000のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Cisco Systems IE 3000の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Cisco Systems IE 3000デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがCisco Systems IE 3000を使用するのを助ける技術的文書のことです。説明書は通常、全てのCisco Systems IE 3000ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Cisco Systemsの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Cisco Systems IE 3000の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははCisco Systems IE 3000の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Cisco Systems IE 3000に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Cisco Systems IE 3000デバイスの基本機能を使うにあたってのヒント。 Cisco Systems IE 3000のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Cisco Systems IE 3000に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるCisco Systems IE 3000のメーカー/サービスへの連絡先に関する情報。

Cisco Systems IE 3000についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもCisco Systems IE 3000の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがCisco Systems IE 3000で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)