Lenovo 8155の取扱説明書

42ページ 1.31 mb
ダウンロード

ページに移動 of 42

Summary
  • Lenovo 8155 - page 1

    Hard w ar e Rep l ac e m ent Gu i d e Ty p e s 8099 , 81 16 , 815 5 , 815 6 Ty p e s 815 7 , 8 1 58, 81 5 9 , 816 0 Ty p e s 82 1 5 , 92 1 0 , 92 1 1 ...

  • Lenovo 8155 - page 2

    ...

  • Lenovo 8155 - page 3

    Hard w ar e Rep l ac e m ent Gu i d e Ty p e s 8099 , 81 16 , 815 5 , 815 6 Ty p e s 815 7 , 8 1 58, 81 5 9 , 816 0 Ty p e s 82 1 5 , 92 1 0 , 92 1 1 ...

  • Lenovo 8155 - page 4

    Third Edition (October 2005) © Copyright Lenovo 2005. Portions © Copyright International Business Machines Corporation 2005. All rights reserved. U.S. GOVERNMENT USERS – RESTRICTED RIGHTS: Our products and/or services ar e provided with RESTRICTED RIGHTS. Use, duplication or disclosure by the Government is subject to the GSA ADP Schedule contra ...

  • Lenovo 8155 - page 5

    Contents Overview . . . . . . . . . . . . . .v Safety information for replacing CRUs . . . . . .v Safety information for replacing FRUs . . . . . .v Additional information resour ces . . . . . . .v T ools requir ed . . . . . . . . . . . . .v i Handling static-sensitive devices . . . . . . .v i Chapter 1. Locations . . . . . . . . .1 Locating compon ...

  • Lenovo 8155 - page 6

    iv Hardwar e Replacement Guide ...

  • Lenovo 8155 - page 7

    Overview This guide is intended to be used by customers who are r eplacing Customer Replaceable Units (CRUs) as well as trained service personnel who are r eplacing Field Replacement Units (FRUs). In this guide, CRUs and FRUs will often be referr ed to as parts. This guide does not include procedur es for all parts. It is expected that cables, swit ...

  • Lenovo 8155 - page 8

    v Downloads and drivers v Links to other useful sources of information v Support phone list To access this information, point your browser to: http://www .lenovo.com/think/support T ools required To replace some parts in your computer , you might need a flat-blade or Phillips screwdriver . Additional tools might be needed for certain parts. Handlin ...

  • Lenovo 8155 - page 9

    Chapter 1. Locations This chapter provides illustrations to help locate the various connectors, contr ols, and components of the computer . To open the computer cover , see “Opening the cover” on page 5. Locating components The following illustration will help you locate the various components in your computer . 1 Diskette drive lock 7 ...

  • Lenovo 8155 - page 10

    Locating controls and connectors on the front of your computer The following illustration shows locations of the controls and connectors on the front of your computer . Note: Not all computer models will have the following controls and connections. 1 Optical drive or second hard disk drive (some models) 5 USB connectors (2) 2 Hard ...

  • Lenovo 8155 - page 11

    Locating connectors on the rear of your computer The following illustration shows locations of connectors on the rear of your computer . 1 Power cord connector 9 Parallel connector 2 Cable lock (Kensington) latch 10 Audio line-in connector 3 PCI Express (x1) adapter connector 11 Audio line-out connector 4 P ...

  • Lenovo 8155 - page 12

    Identifying parts on the system board The following illustration shows the locations of parts on the system board. 1 Memory connector 1 9 Diskette drive connector 2 Memory connector 2 10 Front panel connector 3 S ATA IDE connectors (2) 11 Power supply connector 4 Chassis intrusion switch 12 PATA prima ...

  • Lenovo 8155 - page 13

    Chapter 2. Replacing hardware Attention Do not open your computer or attempt any repair befor e reading the “Important safety information” in the Quick Reference that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer . To obtain copies of the Quick Reference or the HMM , go to the Support We b site at ...

  • Lenovo 8155 - page 14

    Replacing the power supply Attention Do not open your computer or attempt any repair befor e reading the “Important safety information” in the Quick Reference that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer . To obtain copies of the Quick Reference or the HMM , go to the Support We b site at htt ...

  • Lenovo 8155 - page 15

    5. Disconnect the power supply cables from the hard disk drive and optical drive. 6. Disconnect the power supply cables 1 and 2 from the system board connectors and from all drives. 7. Remove the power supply cables from the cable clips and ties. 8. Slide the power supply forward and remove fr om the computer . 9. Install the new power ...

  • Lenovo 8155 - page 16

    Replacing the system board assembly Attention Do not open your computer or attempt any repair befor e reading the “Important safety information” in the Quick Reference that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer . To obtain copies of the Quick Reference or the HMM , go to the Support We b si ...

  • Lenovo 8155 - page 17

    4. While holding the rear of the computer chassis down, pull upward on the handle provided to r emove the PCI riser assembly and any adapters that are currently installed. 5. Disconnect the cables connected to the system board. See “Identifying parts on the system board” on page 4. Important Note the cable routing. It is important to r oute the ...

  • Lenovo 8155 - page 18

    Note: Yo u will have to tilt the system board assembly and move it around the edge of the power supply assembly to remove it fr om the computer . 7. Place the defective system board next to the new system board on a clean, flat surface. 8. Release the lever 1 holding the microprocessor heat sink. 9. Remove the heat sink from the system board. ...

  • Lenovo 8155 - page 19

    11 . Use the vacuum pen 1 to lift the microprocessor straight up and out of the socket. Important Do not touch the gold contacts on the bottom of the micropr ocessor . Use the vacuum pen provided to r emove and install the microprocessor . If you must touch the micropr ocessor , touch only the sides. a. Note the orientation of the notches  ...

  • Lenovo 8155 - page 20

    14. Use the vacuum pen 1 to lower the microprocessor straight down into the micropr ocessor socket. 15. Lower the microprocessor r etainer and secure it with the lever . Note: There will be a black plastic cover on the micr oprocessor retainer to protect the socket on the new system boar d. When you lock the micropr ocessor in position, remov ...

  • Lenovo 8155 - page 21

    Important When you receive a new micr oprocessor , you will also receive a new heat sink and vacuum pen. Yo u must use the new heat sink with the new micropr ocessor . If you use the old heat sink with the new micr oprocessor , your computer might overheat causing intermittent pr oblems. Important Do not touch the gold contacts on the bottom of the ...

  • Lenovo 8155 - page 22

    3. Release the lever 1 holding the microprocessor heat sink. 4. Remove the heat sink from the system board. Important Do not use the old heat sink with the a new micropr ocessor . If you use the old heat sink with the new micropr ocessor , your computer might overheat causing intermittent pr oblems. 5. Release the lever 1 for the microp ...

  • Lenovo 8155 - page 23

    6. Use the vacuum pen 1 to lift the microprocessor straight up and out of the socket. Important Do not touch the gold contacts on the bottom of the micropr ocessor . If you must touch the micropr ocessor , touch only the sides. a. Note the orientation of the notches 1 on the microprocessor . This is important when reinstalling the micr ...

  • Lenovo 8155 - page 24

    8. Loosen the black cover 3 that protect the gold contacts on the new micropr ocessor 2 , but do not remove the black cover . Use the vacuum pen 1 to pick up the micropr ocessor , and then completely remove the black cover . * XXXXXXXXX* 9. Position the microprocessor so that the notches on the micr oprocessor are aligned with the ...

  • Lenovo 8155 - page 25

    12. Place the new heat sink into position and lower the lever 1 to secure the heat sink. 13. Go to “Completing the CRU replacement” on page 28. Replacing a memory module Attention Do not open your computer or attempt any repair befor e reading the “Important safety information” in the Quick Reference that was included with your comput ...

  • Lenovo 8155 - page 26

    2. While holding the rear of the computer chassis down, pull upward on the handle provided to r emove the PCI riser assembly and any adapters that are currently installed. 3. Pivot the drive bay assembly upward to gain access to the memory module. 4. Locate the memory connectors. See “Identifying parts on the system board” on page 4. 18 Hardwar ...

  • Lenovo 8155 - page 27

    5. Remove the memory module being replaced by opening the retaining clips as shown. 6. Position the replacement memory module over the memory connector . Make sure the notch 1 on the memory module aligns corr ectly with the connector key 2 on the system board. Push the memory module straight down into the connector until the retaining c ...

  • Lenovo 8155 - page 28

    2. While holding the left rear of the computer chassis down, pull upward on the handle provided to r emove the PCI riser assembly including any adapters that are alr eady installed. 3. Pivot the adapter latch to release the adapter . 4. Remove the adapter being replaced from the PCI riser . 5. Remove the new adapter from its static-protective packa ...

  • Lenovo 8155 - page 29

    8. Pivot the adapter latch to the closed position to secure the adapters. 9. Reinstall the PCI riser and adapters. 10. Go to “Completing the CRU replacement” on page 28. Replacing a hard disk drive Attention Do not open your computer or attempt any repair befor e reading the “Important safety information” in the Quick Reference that was inc ...

  • Lenovo 8155 - page 30

    6. Remove the defective hard disk drive from the bracket by flexing the bracket. Note: Make sure you notice the orientation of the har d disk drive in the blue bracket. 22 Hardwar e Replacement Guide ...

  • Lenovo 8155 - page 31

    7. Install the new drive into the blue bracket, flex the bracket, and align the pins 1 through 4 on the bracket with the holes in the har d disk drive. Do not touch the circuit boar d 5 on the bottom of the hard disk drive. 8. Insert the new hard disk drive and bracket into the hard disk drive bay and snap into position. 9. Pivot ...

  • Lenovo 8155 - page 32

    2. Pivot the drive bay assembly upward to gain access to the cable connections. 3. Disconnect the signal and power cables from the rear of the optical drive. 4. Slide the optical drive lock 1 to the unlocked position. 5. Open the door at the front of the optical drive and slide it out the front of the computer . 6. Install the new optical dri ...

  • Lenovo 8155 - page 33

    Replacing the diskette drive Attention Do not open your computer or attempt any repair befor e reading the “Important safety information” in the Quick Reference that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer . To obtain copies of the Quick Reference or the HMM , go to the Support We b site at h ...

  • Lenovo 8155 - page 34

    Replacing the keyboard Attention Do not open your computer or attempt any repair befor e reading the “Important safety information” in the Quick Reference that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer . To obtain copies of the Quick Reference or the HMM , go to the Support We b site at http:// ...

  • Lenovo 8155 - page 35

    3. Locate the connector for the mouse. See “Locating controls and connectors on the front of your computer” on page 2 and “Locating connectors on the r ear of your computer” on page 3. Note: Y our mouse might be connected to the standar d mouse connector 1 at the rear of the computer or to a USB connector 2 at either the fr ont ...

  • Lenovo 8155 - page 36

    3. Locate the speaker 1 See “Locating components” on page 1. 4. Disconnect the speaker cable from the system board. See “Identifying parts on the system board” on page 4. Note: Make sure you note the location of the speaker cable when you disconnect it from the system boar d. 5. Remove the speaker by sliding it upward and out of the r ...

  • Lenovo 8155 - page 37

    2. Make sure that the cables are r outed correctly before lowering the drive bay assembly . 3. Lower the drive bay assembly and position the drive locks to the locked position. Otherwise, you cannot close the computer cover . 4. Close the computer cover . 5. Re-installed any locking devices, such as a Kensington lock, that secure the computer cover ...

  • Lenovo 8155 - page 38

    3. When you are prompted to select a language, pr ess the number on your keyboard that corr esponds to the language and then press Enter . 4. When prompted to change the serial number , press Y. 5. T ype in the seven character serial number of your computer and then press Enter . 6. When prompted to change the machine type/model, press Y. 7. T ype ...

  • Lenovo 8155 - page 39

    Appendix. Notices Lenovo may not offer the pr oducts, services, or features discussed in this document in all countries. Consult your local Lenovo repr esentative for information on the products and services curr ently available in your area. Any refer ence to a Lenovo product, program, or service is not intended to state or imply that only that Le ...

  • Lenovo 8155 - page 40

    vary significantly . Some measurements may have been made on development-level systems and there is no guarantee that these measur ements will be the same on generally available systems. Furthermore, some measur ements may have been estimated through extrapolation. Actual r esults may vary . Users of this document should verify the applicable data ...

  • Lenovo 8155 - page 41

    ...

  • Lenovo 8155 - page 42

    Part Number: 39J8231 Printed in USA (1P) P/N: 39J8231 ...

メーカー Lenovo カテゴリー Laptop

Lenovo 8155のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 8155の取扱説明書
- Lenovoの製品カード
- パンフレット
- またはLenovo 8155の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Lenovo 8155の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Lenovo 8155の取り付け説明書、サービスマニュアル、簡易説明書、またはLenovo 8155のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Lenovo 8155の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Lenovo 8155デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがLenovo 8155を使用するのを助ける技術的文書のことです。説明書は通常、全てのLenovo 8155ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Lenovoの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Lenovo 8155の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははLenovo 8155の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Lenovo 8155に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Lenovo 8155デバイスの基本機能を使うにあたってのヒント。 Lenovo 8155のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Lenovo 8155に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるLenovo 8155のメーカー/サービスへの連絡先に関する情報。

Lenovo 8155についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもLenovo 8155の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがLenovo 8155で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)