Husqvarna GTH27V48LSの取扱説明書

44ページ 3.55 mb
ダウンロード

ページに移動 of 44

Summary
  • Husqvarna GTH27V48LS - page 1

    07002 GTH27V48LS Owner's Manual 532 43 86-87 ...

  • Husqvarna GTH27V48LS - page 2

    2 SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAP ABLE OF AMPUT A TING HANDS AND FEET AND THROW ING OBJECTS. F AILURE TO OBSERVE THE FOLL OWING SAFETY INSTRUCTIONS COULD RESUL T IN SERIOUS INJURY OR DEA TH. I. GENERAL OPERA TION • Read, understand, and follow all instructions on the machine and in the ...

  • Husqvarna GTH27V48LS - page 3

    3 SAFETY RULES Safe Operation Practices for Ride-On Mowers • Be sure the area is clear of bystanders before operat- ing. Stop machine if anyone enters the area. • Never carry passengers. • Do not mow in reverse unless absolutely necessary . Al ways look down and behind before and while back- ing. • Never carry children, even with the blades ...

  • Husqvarna GTH27V48LS - page 4

    4 SAFETY RULES ......................................................... 2-3 PRODUCT SPECIFICA TIONS ....................................... 4 CUSTOMER RESPONSIBILITIES ................................. 4 ASSEMBL Y ................................................................. 5-6 OPERA TION ...................................................... ...

  • Husqvarna GTH27V48LS - page 5

    5 UNAS SEMBLED P ARTS Keys (2) Keys Slope Sheet Y our new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. ADJUST SEA T (See Fig. 2) • Sit in seat. • Lift up adjustment lever (A) and slide seat until a com- fortable position is reached which allows you to press clutch/brake peda ...

  • Husqvarna GTH27V48LS - page 6

    6 AS SEMBL Y CHECK TIRE PRESSURE The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance. • Reduce tire pressure to PSI shown on tires. CHECK DECK LEVELNESS For best cutting results, mower housing should be prop- erly leveled. See “TO LEVEL MOWER HOUSING? ...

  • Husqvarna GTH27V48LS - page 7

    7 OPERA TION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models only) KEEP AREA CLEAR SLOPE HAZARDS 15 15 (SEE SAFETY RULES SECTION) BATTERY REVERSE FORWARD FAST SLOW ENGINE ON ENGINE OFF FUEL CHOKE MOWER HEIGHT REVERS ...

  • Husqvarna GTH27V48LS - page 8

    8 OPERA TION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERA TING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference. Our tractors conform to the applicable safety standards of the American Nati ...

  • Husqvarna GTH27V48LS - page 9

    9 OPERA TION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye dam age. Always wear safety glass es or eye shields while operating your tractor or per form ing any ad just ments or repairs. W e rec om mend standard safety glasses or a wide vision safety mask worn over spectacles. HOW TO ...

  • Husqvarna GTH27V48LS - page 10

    10 OPERA TION TO ADJUST MOWER CUT TING HEIGHT (See Fig. 8) The po si tion of the at tach ment lift le ver (A) de ter mines the cut ting height. TO MOVE FORWARD AND BACK WARD (See Fig. 7) The direction and speed of movement is controlled by the forward and reverse drive pedals. • Start tractor and release parking brake. • Slowly depress forward ...

  • Husqvarna GTH27V48LS - page 11

    11 Fig. 10 OPERA TION Fig. 12 Fig. 11 TO TRANSPORT (See Figs. 3 and 12) When pushing or towing your tractor , be sure to disengage transmission by placing freewheel control in free wheel ing po- si tion. Free wheel control is located at the rear drawbar of tractor . • Raise attachment lift to highest position with at tach ment lift control. • P ...

  • Husqvarna GTH27V48LS - page 12

    12 OPERA TION CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame. IMPORT ANT : WHEN OPERA TING IN TEMPERA TURES BEL OW 32°F(0°C), USE FRESH, CLEAN WINTER GRADE GAS O LINE TO HELP ENSURE GOOD COLD WEA THER ST ART ING. CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can att ...

  • Husqvarna GTH27V48LS - page 13

    13 Fig. 14 MOWING TIPS • Mower should be properly leveled for best mowing performance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual. • The left hand side of mower should be used for trim- ming. • Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the right of ...

  • Husqvarna GTH27V48LS - page 14

    14 MAINTENANCE T R A C T 0 R 1 - Change more often when operating under a heavy load or in high ambient temperatures . 2 - Service more often when operating in dir ty or dusty conditions. E N G I N E 3 2 2 2 2 3 - Replace blades more often when mowing in sandy soil. 4 - Not required if equipped with maintenance-free battery . 5 - See Cleaning in Ma ...

  • Husqvarna GTH27V48LS - page 15

    15 MAINTENANCE TRACTOR Always observe safety rules when per form ing any main te nance. BRAKE OPERA TION If tractor requires more than five (5) feet to stop at highest speed in high est gear on a level, dry concrete or paved surface, then brake must be checked and ad just ed. (See “TO CHECK BRAKE” in the Ser vice and Ad just ments section of th ...

  • Husqvarna GTH27V48LS - page 16

    16 MAINTENANCE V -BEL TS Check V -belts for deterioration and wear after 100 hours of operation and replace if necessary . The belts are not ad just able. Re place belts if they begin to slip from wear . ENGINE LUBRICA TION Only use high quality detergent oil rated with API service classification SG-SL. Select the oil’s SAE viscosity grade accord ...

  • Husqvarna GTH27V48LS - page 17

    17 MAINTENANCE CL AMP FUEL FIL TER Fig. 19 IN-LINE FUEL FIL TER (See Fig. 19) The fuel filter should be replaced once each season. If fuel filter becomes clogged, ob struct ing fuel flow to car bu re tor , re place ment is re quired. • With engine cool, remove filter and plug fuel line sec- tions. • Place new fuel filter in position in fuel lin ...

  • Husqvarna GTH27V48LS - page 18

    18 WARNING: TO A VOID SERIOUS INJURY , BEFORE PERFORMING ANY SER VICE OR AD JUST MENTS: • Depress brake pedal fully and set parking brake. • Place attachment clutch in “DISENGAGED” position. • T urn ignition key to “STOP ” and remove key . • Make sure the blades and all moving parts have completely stopped. • Disconnect spark plug ...

  • Husqvarna GTH27V48LS - page 19

    19 SERVICE AND ADJUSTMENTS Fig. 28 Fig. 29 • Install belt onto electric clutch pulley (M). Fig. 26 Fig. 27 • A TT ACH REAR LIFT LINKS (C) - Lift rear corner of mower and position slot in link assembly over pin on rear mower bracket (D) and secure with washer and retainer spring. • Repeat on opposite side of tractor . • A TT ACH FRONT LINK ( ...

  • Husqvarna GTH27V48LS - page 20

    20 SERVICE AND ADJUSTMENTS FRONT - TO-BACK ADJUSTMENT (See Figs. 32 & 33) IMPORT ANT : Deck must be level side-to-side. T o obtain the best cutting re sults, the mower blades should be adjusted so the front tip is 1/8" to 1/2" lower than the rear tip when the mower is in its highest position. CAUTION: Blades are sharp. Protect your ha ...

  • Husqvarna GTH27V48LS - page 21

    21 SERVICE AND ADJUSTMENTS TO CHECK BRAKE If tractor requires more than five (5) feet to stop at highest speed in high est gear on a level, dry concrete or paved surface, then brake must be serviced. Y ou may also check brake by: • Park tractor on a level, dry concrete or paved surface, depress brake pedal all the way down and engage parking brak ...

  • Husqvarna GTH27V48LS - page 22

    22 Fig. 37 Fig. 38 RE T AIN ING RING WASH ERS SQUARE KEY (REAR WHEEL ONL Y) AXLE COVER TO REMOVE WHEEL (See Fig. 38) • Block up axle securely . • Remove axle cover , retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose). • Repair tire and reassemble. • On rear wheels only: align grooves in rear w ...

  • Husqvarna GTH27V48LS - page 23

    23 TO ST ART ENGINE WITH A WEAK BA TTERY (SEE FIG. 39) WARNING : Lead-acid batteries gen er ate ex plo sive gases. Keep sparks, flame and smoking ma te ri als away from bat ter ies. Always wear eye pro tec tion when around batteries. If your battery is too weak to start the engine, it should be recharged. (See "BA TTERY" in the MAINTENANC ...

  • Husqvarna GTH27V48LS - page 24

    24 TO REPL ACE HEADLIGHT BULB • Raise hood. • Pull bulb holder out of the hole in the backside of the grill. • Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill. • Close hood. INTERL OCKS AND REL A YS Loose or damaged wiring may cause your tractor to run poorly , stop running, or prevent it ...

  • Husqvarna GTH27V48LS - page 25

    25 Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. WARNING : Never store the trac tor with gas o line in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any en clo sure. TRACTOR Remove mower from tractor ...

  • Husqvarna GTH27V48LS - page 26

    26 PROBLEM CAUSE CORRECTION Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly . 2. See “TO ST ART ENGINE” in Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start. 4. Bad spark plug. 4. Replace spark plug. 5. Dirty air filter . 5. Clean/replace air filter . 6. Dirty fuel fil ...

  • Husqvarna GTH27V48LS - page 27

    27 PROBLEM CAUSE CORRECTION Engine continues to run when oper- ator leaves seat with attachment clutch engaged 1. Faulty operator -safety presence control system. 1. Check wiring, switches and connections. If not corrected, contact an authorized service center/ department. Poor cut - uneven 1. Worn, bent or loose blade. 1. Replace blade. Tighten bl ...

  • Husqvarna GTH27V48LS - page 28

    28 TRACTOR - MODEL NO . GTH27V48LS (96043011700), PRODUCT NO . 960 43 01-17 DECALS NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm KEY P ART NO . NO . DESCRIPTION 6 2 1 3 11 4 10 5 9 8 7 wheel_art_1-vgt WHEELS AND TIRES KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION 17 16 16 1 532 05 91-92 Cap, V alve, Tire 2 5 ...

  • Husqvarna GTH27V48LS - page 29

    29 NO TES M FUSE ST ARTER SOLENOID BA TTERY ELECTRIC CLUTCH CLUTCH/BRAKE (PED AL UP) REVERSE SWITCH (NO T IN REVERSE) SEA T SWITCH (NO T OCCUPIED) SHORTING CONNECT OR CHASSIS HARNESS IGNITION UNIT HOUR METER REGULA TOR CHASSIS HARNESS CONNECT OR (MA TING SIDE) D ASH HARNESS CONNECT OR (MA TING SIDE) LIGHT SWITCH HEADLIGHTS ST A T OR FUEL LINE FUEL ...

  • Husqvarna GTH27V48LS - page 30

    30 TRACTOR - MODEL NO . GTH27V48LS (96043011700), PRODUCT NO . 960 43 01-17 ELECTRICAL 8 1 99 100 91 2 27 90 28 55 26 43 41 24 27 25 30 33 22 79 21 40 71 34 16 42 T14S 29 With 12V Outlet Option 59 103 46 45 0 60 AMPS 60 141 ...

  • Husqvarna GTH27V48LS - page 31

    31 TRACTOR - MODEL NO . GTH27V48LS (96043011700), PRODUCT NO . 960 43 01-17 ELECTRICAL KEY P ART NO . NO . DESCRIPTION 1 532 16 34-65 Battery 2 874 76 04-12 Bolt Hex Hd 1/4-20 unc x 3/4 8 532 18 64-91 Battery Box 16 532 17 61-38 Switch Interlock 21 532 40 02-52 Harness Socket Light 22 532 00 41-52 Bulb, Light #1156 24 532 40 02-53 Cable Battery 25 ...

  • Husqvarna GTH27V48LS - page 32

    32 TRACTOR - MODEL NO . GTH27V48LS (96043011700), PRODUCT NO . 960 43 01-17 CHASSIS 182 176 176 175 150 130 177 176 14 130 130 130 202 203 208 18 15 25 207 5 176 176 205 151 206 3 137 137 214 204 297 191 chassis-tex_GT HUSQ II_8 130 37 194 194 178 161 36 36 199 162 196 221 162 58 189 189 235 159 159 152 236 236 183 165 2 159 159 180 217 68 228 194 ...

  • Husqvarna GTH27V48LS - page 33

    33 TRACTOR - MODEL NO . GTH27V48LS (96043011700), PRODUCT NO . 960 43 01-17 CHASSIS KEY P ART NO . NO . DESCRIPTION 2 532 19 42-61 Drawbar 3 532 43 97-52 Applique 5 532 43 74-77 Dash 14 532 43 97-25 Hood 15 532 43 97-33 Lens LH 18 532 43 77-62 Grille Asm 25 532 43 97-32 Lens RH 36 817 06 05-12 Screw 5/16-18 x 3/4 37 532 40 18-25 F ender 58 532 19 4 ...

  • Husqvarna GTH27V48LS - page 34

    34 TRACTOR - MODEL NO . GTH27V48LS (96043011700), PRODUCT NO . 960 43 01-17 DRIVE 184 221 42 64 188 208 210 211 211 166 17 161 35 167 160 160 203 163 214 125 215 222 56 197 196 15 29 306 153 153 159 15 116 73 2 145 3 7 9 69 33 2 145 1 33 69 3 121 286 114 125 125 125 80 213 221 160 206 26 207 209 92 125 116 drive-tex_G700_pedal_6 48 190 189 50 51 52 ...

  • Husqvarna GTH27V48LS - page 35

    35 TRACTOR - MODEL NO . GTH27V48LS (96043011700), PRODUCT NO . 960 43 01-17 DRIVE KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION 1 - - - - - - T ransaxle, Hydro G7-BCBB-1XDC -1FCA 2 532 00 70-70 Key 1/4 x 2.5 3 532 00 75-63 Washer Thrust Axle Hardened 7 532 19 98-37 Hub Asm. Wheel 9 532 14 00-80 Bolt Hub Wheel 15 819 13 13-16 Washe ...

  • Husqvarna GTH27V48LS - page 36

    36 TRACTOR - MODEL NO . GTH27V48LS (96043011700), PRODUCT NO . 960 43 01-17 ENGINE         30 !2+ª !22%34%2ª+)4                 ENGINETEX?BSCYL?         ...

  • Husqvarna GTH27V48LS - page 37

    37 KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm For engine service and replacement parts, call the toll free number for your engine manufacturer listed below: Briggs & Stratton 1-800-233-3723 1 - - - - - - Engine B&S Model No. 44Q777-2406-G1 2 532 14 97-23 Muffler 9 532 40 86-67 Keeper ...

  • Husqvarna GTH27V48LS - page 38

    38 TRACTOR - MODEL NO . GTH27V48LS (96043011700), PRODUCT NO . 960 43 01-17 STEERING ASSEMBL Y KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 55 35 19 63 60 59 58 67 54 67 78 66 54 65 61 55 2 Steering-tex_LEGND2_36_r1 6 5 13 13 53 8 62 4 50 50 70 65 68 69 15 15 14 ...

  • Husqvarna GTH27V48LS - page 39

    39 TRACTOR - MODEL NO . GTH27V48LS (96043011700), PRODUCT NO . 960 43 01-17 SEA T ASSEMBL Y 1 532 42 40-73 Seat 2 532 18 01-66 Bracket Pivot F ender 3 532 14 06-75 Strap, Asm F ender 6 873 80 06-00 Nut, Lock w/Ins. 3/8-16 unc 7 532 12 41-81 Spring, Seat Cprsn 8 532 17 18-77 Bolt 5/16-18 unc x 3/4 w/Sems 10 532 19 69-77 Pan, Seat 21 532 17 18-52 Bol ...

  • Husqvarna GTH27V48LS - page 40

    40 TRACTOR - MODEL NO . GTH27V48LS (96043011700), PRODUCT NO . 960 43 01-17 MOWER DECK 3 4 5 8 9 10 12 13 14 18 19 22 23 16 33 27 28 29 30 31 32 33 34 35 37 38 39 44 45 46 48 49 50 51 52 53 54 55 56 57 1 2 6 7 11 15 16 17 20 21 36 47 58 60 24 25 43 24 59 48_F_elec-T ex_4 61 62 63 ...

  • Husqvarna GTH27V48LS - page 41

    41 TRACTOR - MODEL NO . GTH27V48LS (96043011700), PRODUCT NO . 960 43 01-17 MOWER DECK KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION NOTE : All component dimensions given in U.S. inches 1 inch = 25.4 mm 1 575 43 80-02 Deck w/ Decals 48" 2 539 11 21-70 Housing Assembly 3 539 10 75-20 Washer -Spacer 4 532 17 43-75 Pulley , Mand ...

  • Husqvarna GTH27V48LS - page 42

    42 TRACTOR - MODEL NO . GTH27V48LS (96043011700), PRODUCT NO . 960 43 01-17 MOWER LIFT               LIFTTEX?      2 532 42 20-27 Shaft Asm., Lift 3 532 19 52-30 Lever Asm., Lift RH 7 532 41 15-55 Grip, Lever 10 532 19 63-14 Spring T orsio ...

  • Husqvarna GTH27V48LS - page 43

    43 1 5 DE G REE S M AX . FOLD ALON G DOTTED LINE THI S I S A 1 5 DE G REE S LOPE ONLY RIDE UP AND DO W N HILL, NOT ACRO SS HILL S U GG E S TED G UIDE FOR S I G HTIN G S LOPE S FOR S AFE OPERATION W ARNIN G : To avo i d s er i o us i n ju ry, operate yo u r tra c tor u p and do w n the fa c e of s lope s , never a c ro ss the fa c e . Do not mo w s ...

  • Husqvarna GTH27V48LS - page 44

    10.21.10 TH Printed in the U.S.A. ...

メーカー Husqvarna カテゴリー Lawn Mower

Husqvarna GTH27V48LSのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- GTH27V48LSの取扱説明書
- Husqvarnaの製品カード
- パンフレット
- またはHusqvarna GTH27V48LSの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Husqvarna GTH27V48LSの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Husqvarna GTH27V48LSの取り付け説明書、サービスマニュアル、簡易説明書、またはHusqvarna GTH27V48LSのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Husqvarna GTH27V48LSの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Husqvarna GTH27V48LSデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがHusqvarna GTH27V48LSを使用するのを助ける技術的文書のことです。説明書は通常、全てのHusqvarna GTH27V48LSユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Husqvarnaの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Husqvarna GTH27V48LSの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははHusqvarna GTH27V48LSの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Husqvarna GTH27V48LSに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Husqvarna GTH27V48LSデバイスの基本機能を使うにあたってのヒント。 Husqvarna GTH27V48LSのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Husqvarna GTH27V48LSに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるHusqvarna GTH27V48LSのメーカー/サービスへの連絡先に関する情報。

Husqvarna GTH27V48LSについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもHusqvarna GTH27V48LSの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHusqvarna GTH27V48LSで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)