日本語 dropdown-ico

Agilent Technologies 54754aの取扱説明書

44ページ 0.49 mb
ダウンロード

ページに移動 of 44

Summary
  • Agilent Technologies 54754a - page 1

    Agilent 5475 3A and 54754A TDR Plug-in Modules Programmer’ s Quick Refe rence ...

  • Agilent Technologies 54754a - page 2

    ii Notices © Agilen t T echnologie s, Inc. 2 000-20 04 No pa rt of t his man ual ma y be r epro- duced in any form or by any means (including electronic stor age and retrieval or translation into a foreign lan- guage ) witho ut pri or agre emen t and wr it- ten consent from Ag ilent T echnologies, Inc. as governed by U nited States and inte rnat i ...

  • Agilent Technologies 54754a - page 3

    iii Introduc tion Introduction 54750A/8 3480A Mai nfram es For control ling 5475 3A and 54754A TDR plug -in mod ules that are ins talled in a 54750A or 834 80A mainfram es, refer to th e following books : • Thi s manua l, the 54753 A and 54754A TDR Pl ug-in Modules Programmer’s Quick Reference • 54753A and 54754A Pr ogrammer’s Gui de for de ...

  • Agilent Technologies 54754a - page 4

    iv Introduct ion [ ] Squa re brack ets indicat e that the en clos ed items a re option al. { } When s everal items are e nclosed by braces, o ne, and only one of these elemen ts may be s elected. Definitions d ::= A si ngle ASCII n umeric cha rac ter , 0-9 . n ::= A si ngle AS CII non-ze ro, numeri c cha racter , 1-9. <NL> ::= Newl ine or Lin ...

  • Agilent Technologies 54754a - page 5

    Contents Root Level Com mand s 4 Acqu ire Comman ds 7 Calib rate C om mand s 8 Channel Commands 9 Disk Com mand s 11 Disp lay Comm and s 12 Function Commands 13 Hi s to g r a m C o mm a n d s 1 9 L i mi t T es t C o m ma n d s 2 0 Mar ker C om man ds 21 Mask Test C omm ands 2 3 Measure Commands 25 TDR Commands 37 Waveform Commands 41 Waveform Memor ...

  • Agilent Technologies 54754a - page 6

    Root Leve l Commands Command :BLA Nk {CH ANne l<nu mber > | WMEM ory< numb er> | FUNC tion <nu mber > | FFT | RE SPon se<num ber> | HIST ogra m | PMEM ory1 } Tur ns off an ac tiv e chann e l, funct ion, wa vefo rm memo ry, pixe l memor y, F FT, hist ogr am, or TD R respo nse. The V IEW co mmand t urn s them on. <number> ...

  • Agilent Technologies 54754a - page 7

    Command :DIG itiz e [<wa vefo rm_n ame> ][,< wave form _nam e>] Invokes a special mode of data acquisition that is more efficient than using the RUN co mmand . Th is com man d in itia lizes the selec ted chan nels , functions, responses, or FFT to “unacquired,” then acquires them according to t he current instru me nt s ettin gs. Wh ...

  • Agilent Technologies 54754a - page 8

    Command :STO Re:W AVEf orm {C HANn el<n umbe r> | FUN Ct io n< nu mb er > | WMEM or y< nu mb er > | HI ST ogra m | FFT | RE SPon se<n umbe r>}, {WME Mory <num ber> } Copi es a c han nel, f unc tion , sto red wa vefo rm, hist ogram , TD R respo nse, or FFT to a wavefo rm me mory . The fir st para met ers s pecif ies t h ...

  • Agilent Technologies 54754a - page 9

    Acquire Commands Command :ACQ uire :BES T[?] {TH Rupu t | FLATne ss} Wh en avera gin g is enab led wit h ACQuire: AVERage, the FLAT ness opt ion impr ov es the ste p flat ness by usin g a signal pr ocess ing algori thm w ithi n the inst rument . Yo u sho uld us e this op t ion whe n perfo rming TDR mea surem ents or when s tep flatness i s importan ...

  • Agilent Technologies 54754a - page 10

    Cali bra te C ommands Command :CAL ibra te:S AMPl ers[ ?] {DI Sabl e | ENAB le} Enab les or d isables the samp le rs in the plu g-in. 8 ...

  • Agilent Technologies 54754a - page 11

    Channel Commands Command :CHA Nnel <num ber> :OFF Set[ ?] < offs et_v alue > For TDR an d TDT app licat ion s, you may change the offs et to magn ify of fset in som e circu ms tances . This com m and is used t o set the ma gni fy off set as well as the of fset. <number> An in t eg er, 1-4 , indi cating the slot in wh ich the chan ...

  • Agilent Technologies 54754a - page 12

    Command :CHA Nnel <num ber> :TDR Skew <pe rcen t> [ %] This co mmand set s the TD R skew fo r the given chann el. The TD R skew cont rol mo ves th e TDR st ep re lative t o the tr igger po sition. The contro l may be se t fro m - 100 to 100 pe rcen t of t he al lowab le range. This co mmand is only app licab le to TD R cha nnels . <n ...

  • Agilent Technologies 54754a - page 13

    Disk Commands Command :DI SK :L OA D "< fi le name >" , <s ou rc e> Loads a setup, waveform, datab ase, mask, TDR/TDT calibration, or pixel memory from the disk. The filename does not include a suffix. The suffix supplied by the instrument depends on the source and fil e format specified. The T DRTD T op tion is a fil e type c ...

  • Agilent Technologies 54754a - page 14

    Displ ay Commands Command :DIS Play :ASS ign[ ?] { CHAN nel< numb er> | FUN Ct io n< nu mb er > | RESP on se <n um be r> | WMEM ory< numb er> | FF T},{ UPPe r | LOWe r} Assign s the spec ifi ed cha nnel , wav efo rm, func tion , TDR resp onse , or F FT to a par ticu lar por tion of t he wavefo rm are a on th e scr een. This ...

  • Agilent Technologies 54754a - page 15

    Function Commands Command :FUN Ctio n{1 | 2} :ADD <so urce >[,<so urce >] Defines a functio n that takes the alge braic sum of two defined operands. <source> {CH AN ne l< nu mb er > | FUNC ti on <n um be r> | RES Po ns e< nu mb er > | WMEM or y< nu mb er > | <flo at_v alue >} <number> For chann ...

  • Agilent Technologies 54754a - page 16

    Command :FUN Ctio n{1 | 2} :DIF Fere ntia te {CH ANne l<nu mber > | FUN Ct io n< nu mb er > | RESP on se <n um be r> | WMEM ory< numb er> | <f loat _val ue>} Computes the dis crete derivative of the defined operand’s waveform. <number> For chann els: an int eger, 1 thro ugh 4, ind icating the slo t in wh ich th ...

  • Agilent Technologies 54754a - page 17

    Command :FUN Ctio n{1 | 2} :INT egra te {CH ANne l<nu mber > | FUN Ct io n< nu mb er > | RESP on se <n um be r> | WMEM ory< numb er> | <f loat _val ue>} Defines a function that computes the i ntegral of the defined operand’s waveform. <number> For chann els: an int eger, 1 thro ugh 4, ind icating the slo t in w ...

  • Agilent Technologies 54754a - page 18

    <number> For chann els: an int eger, 1 thro ugh 4, ind icating the slo t in wh ich the chan nel resi des, foll owed by an o ptio nal A or B iden tifyi ng which o f tw o poss ible cha nnels in th e slot is b eing r eference d. For f unctio ns: 1. For wa vefo rm mem ories ( WMEM ory ) : 1, 2, 3, or 4. Fo r TD R respo nses: 1 , 2, 3 , or 4. < ...

  • Agilent Technologies 54754a - page 19

    Command :FUN Ctio n{1 | 2} :MUL Tipl y <sou rce> [,<s ourc e>] Defines a function that alg ebraically multipli es the fi rst operand by the second operand. <source> {CH AN ne l< nu mb er > | FUNC ti on <n um be r> | RES Po ns e< nu mb er > | WMEM or y< nu mb er > | <flo at_v alue >} <number> For ...

  • Agilent Technologies 54754a - page 20

    Command :FUN Ctio n{1 | 2} :VER Sus <s ourc e>[, <sou rce> ] Defines a function for an X- versus-Y display . The fi rst operand defines the Y axis and the se cond defines the X axis . The Y-axi s range and offset are init ially equa l to that of the first o pera nd an d can b e ad just ed wi t h th e RANGE and OFFSET commands. <sourc ...

  • Agilent Technologies 54754a - page 21

    Histogram Co mmands Command :HIS Togr am:W INDo w:SO URce [?] {C HANn el<n umbe r> | FUN Ct io n< nu mb er > | RESP on se <n um be r> | WMEM ory< numb er> | FF T} Sele cts the source of the hist ogram windo w. Th e histo gram w indow w ill tra ck the source’s vertical and horizontal scal e. <number> For chann els: an ...

  • Agilent Technologies 54754a - page 22

    Limit Test Commands Command :LTE St:S WAVe form [?] <sou rce> ,<de stin atio n>,[ ,<fi lena me>[ ,<fo rmat >]] Sav es wa vefor m s fro m a chan ne l, func tio n, histo gram, TDR re spons e, or wav efo rm me mory in the e vent of a failu re d etected b y the lim it test. Each wave fo rm sou rce can be indiv id ually specif ie ...

  • Agilent Technologies 54754a - page 23

    Marker Commands Command :MAR Ker: MODE [?] {O FF | MAN ual | WA Vefo rm | MEAS urem ent | HI STog ram | TD RTDT } Set s the ma rk er m ode. Command :MA RK er :P RO Pa ga tion [? ] {D IE Le ct ri c | ME Ter | FE ET } <pro pa ga ti on > Sets the propagat ion velocity fo r TDR and TDT measurements. T he propagation may be specified as a dielectr ...

  • Agilent Technologies 54754a - page 24

    Command :MAR Ker: X1Y1 sour ce[? ] {CHA Nnel <num ber> | FUN Ct io n< nu mb er > | RESP on se <n um be r> | WMEM ory< numb er> | HI STog ram | FF T} Sets the source for the X1 and Y1 markers . <number> For chann els: an int eger, 1 thro ugh 4, ind icating the slo t in wh ich the chan nel resi des, foll owed by an o pti ...

  • Agilent Technologies 54754a - page 25

    Mas k Tes t C omm ands Command :MTE St:A MASk :SOU Rce[ ?] { CHAN nel< numb er> | FUN Ct io n< nu mb er > | RESP on se <n um be r> | WMEM ory< numb er> | FF T} Sele cts the sou rce for the inte rpretat ion of the AM ASk:XDEL ta and AMASk :YDELt a par ame t ers when A MASk:UN ITs is set t o CURR ent . When UNITs are CURRent, ...

  • Agilent Technologies 54754a - page 26

    <number> For chann els: an int eger, 1 thro ugh 4, ind icating the slo t in wh ich the chan nel resi des, foll owed by an o ptio nal A or B iden tifyi ng which o f tw o poss ible cha nnels in the slot is being refer ence d. For fun ctio ns: 1 o r 2. For wavef orm mem ories ( WMEM ory ) : 1, 2, 3, or 4. Fo r TD R respo nses: 1 , 2, 3 , or 4. & ...

  • Agilent Technologies 54754a - page 27

    Mea sur e C omman ds Command :MEA Sure :DEL Tati me[? ] [<so urce >[,< sour ce>] ] Measu res th e del ta time betwe en tw o edges. If one so urce i s spe cified, the delt a time from th e leadin g edge of the specif ied source o t the trail ing ed ge of the specified source is measured. If two sources are specified, the delta time from ...

  • Agilent Technologies 54754a - page 28

    Command :MEA Sure :FAL Ltim e[?] [<s ourc e>] Measures the time at the upper threshold o f the fa lling edge , me asur es the tim e at t he low er th resho ld of th e fall ing edge, then calcula tes the fal l time. <source> {CH AN ne l< nu mb er > | FUNC ti on <n um be r> | RES Po ns e< nu mb er > | WMEM or y< nu mb ...

  • Agilent Technologies 54754a - page 29

    Command :MEA Sure :NWI DTh[ ?] [ <sou rce> ] Measures the width of t he first negati ve pulse o n the screen usi ng the mid- thres hold lev els o f the wav efo rm (50 % level s wit h sta nda rd meas urement s selected ). <source> {CH AN ne l< nu mb er > | FUNC ti on <n um be r> | RES Po ns e< nu mb er > | WMEM or y< ...

  • Agilent Technologies 54754a - page 30

    <number> For chann els: an int eger, 1 thro ugh 4, ind icating the slo t in wh ich the chan nel resi des, foll owed by an o ptio nal A or B iden tifyi ng which o f tw o poss ible cha nnels in the slot is being refer ence d. For fun ctio ns: 1 o r 2. For wavef orm mem ories ( WMEM ory ) : 1, 2, 3, or 4. Fo r TD R respo nses: 1 , 2, 3 , or 4. C ...

  • Agilent Technologies 54754a - page 31

    Command :MEA Sure :RIS etim e[?] [<s ourc e>] Measu res t he ris e time of th e fi rst d isplay ed edg e by me asur ing the time at the lower threshold of t he rising edge, measuring the t ime at the uppe r threshold o f the risi ng edge, then cal culating t he rise time. <source> {CH AN ne l< nu mb er > | FUNC ti on <n um be r ...

  • Agilent Technologies 54754a - page 32

    Command :MEA SURE :TED ge[? ] <mea s_th res_ txt> , <slo pe>< occu rren ce>[ ,<so urce >] Measur es t he time i nte rval bet ween t he trigg er event and t he sp ecified thre shol d leve l and t ransit ion . <meas_thres_ txt> {UPP er | MID Dle | LO Wer} <slope> {- ( minus ) f or fal ling | + (p lus) (o ption al) ...

  • Agilent Technologies 54754a - page 33

    Command :MEA Sure :TMI N[?] [<s ourc e>] Measures the time at which the fi rst minimum voltage of the source wave for m oc cur red. Wh en FFT is the speci fied sour ce, the fr equen cy at whic h th e fir st min im um valu e occur re d is measur ed . <source> {CH AN ne l< nu mb er > | FUNC ti on <n um be r> | RES Po ns e< ...

  • Agilent Technologies 54754a - page 34

    Command :MEA Sure :VAM Plit ude[ ?] [ <sou rce> ] Calculates the difference bet ween the top and base volt age of the spe cified sou rce. <source> {CH AN ne l< nu mb er > | FUNC ti on <n um be r> | RES Po ns e< nu mb er > | WMEM or y< nu mb er >} <number> For chann els: an int eger, 1 thro ugh 4, ind icatin ...

  • Agilent Technologies 54754a - page 35

    Command :MEA Sure :VLO Wer[ ?] [ <sou rce> ] Measures the voltage value at the lower threshold of the waveform. <source> {CH AN ne l< nu mb er > | FUNC ti on <n um be r> | RES Po ns e< nu mb er > | WMEM or y< nu mb er >} <number> For chann els: an int eger, 1 thro ugh 4, ind icating the slo t in wh ich the ...

  • Agilent Technologies 54754a - page 36

    Command :MEA Sure :VMI N[?] [<s ourc e>] Measu res th e abso lute min im um vo ltage pre sent on the sele cted sou rce wave fo rm. Wh en FF T is the speci fied s ource , the minim um val ue in the spect rum i s measu red. <source> {CH AN ne l< nu mb er > | FUNC ti on <n um be r> | RES Po ns e< nu mb er > | WMEM or y< ...

  • Agilent Technologies 54754a - page 37

    Command :MEA Sure :VRM S[?] {CY CLe | DI SPlay} , {AC | DC } [,<s ourc e>] Measu re s th e RMS vo lta ge of th e selec ted wavefo rm by su btrac tin g the average value of the waveform from each data point on the display. <source> {CH AN ne l< nu mb er > | FUNC ti on <n um be r> | RES Po ns e< nu mb er > | WMEM or y< ...

  • Agilent Technologies 54754a - page 38

    Command :MEA Sure :VTO P[?] [<s ourc e>] Measu res th e stati stica l top o f the se lected so urce wave form. <source> {CH AN ne l< nu mb er > | FUNC ti on <n um be r> | RES Po ns e< nu mb er > | WMEM or y< nu mb er >} <number> For chann els: an int eger, 1 thro ugh 4, ind icating the slo t in wh ich the c ...

  • Agilent Technologies 54754a - page 39

    TD R Co mman ds Command :TD R{ 2 | 4} :R ES Po ns e{1 | 2 | 3 | 4} :C AL ib ra te Begins a TDR or TD T normalization and re ference plane cal ibration. Which calibratio n is done (TDR or TDT) depe nds on the se tting of the TDRTDT control. Command :TD R{ 2 | 4} :R ES Po ns e{1 | 2 | 3 | 4} :C AL ib ra te :CAN Cel Activates the cancel softkey duri n ...

  • Agilent Technologies 54754a - page 40

    Command :TDR {2 | 4}: RATE [?] {A UTO | <r ate> } Set s th e peri od of the TD R pulse gene rato r. Yo u sho uld usu al ly leave this set to AUTO unle ss you nee d to define a s pecific rate. In A UTO, the ins trument will attempt to keep subseq uent per iods o ff screen wh en the tim ebase is changed. <rate> Per iod to wh ich you want ...

  • Agilent Technologies 54754a - page 41

    Command :TD R{ 2 | 4} :R ES Po ns e{1 | 2 | 3 | 4} :R IS et im e[ ?] <ris etim e> Set s th e riseti me for the no rmaliz ed r espo nse. The risetim e sett ing is li mited by t he timeb ase setti ngs and the record lengt h. <risetime> Riseti me setting in se conds. Command :TD R{ 2 | 4} :R ES Po ns e{1 | 2 | 3 | 4} :T DR De st [? ] CHAN ...

  • Agilent Technologies 54754a - page 42

    Command :TD R{ 2 | 4} :R ES Po ns e{1 | 2 | 3 | 4} :V ER Ti ca l[ ?] {TSO urce | M ANua l} Specifies whether the TDR/TDT response should track the source channel ’s vert ical scale (T SOu rce), o r use a user- defined scale specifi ed with t he VER Tical:O FFS et and VERT ical:RA N Ge c om mand s (M ANual) . TSOu rce is the usual setting. Command ...

  • Agilent Technologies 54754a - page 43

    Wavefor m Commands Command :WAV efor m:SO URce [?] {C HANn el<n umbe r> | FUN Ct io n< nu mb er > | RESP on se <n um be r> | WMEM ory< numb er> | DA Taba se | HIS Togr am | FFT } Selects a channel, function, TDR response, waveform memo ry, database, hist o g ram, o r FF T as t he wave for m s ource. <number> For chann ...

  • Agilent Technologies 54754a - page 44

    Wavefor m Memor y Co mmands Command :WME Mory <num ber> :SAV E {CHA Nnel <num ber> | FUN Ct io n< nu mb er > | RESP on se <n um be r> | WMEM ory< numb er> | HI STog ram | FF T} Sto res th e spec ifi c chan nel, wav efo rm me mory , funct ion, hist ogra m, or FFT to t he wavefo rm m emo ry. <number> For chann els: ...

メーカー Agilent Technologies カテゴリー Sprinkler

Agilent Technologies 54754aのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 54754aの取扱説明書
- Agilent Technologiesの製品カード
- パンフレット
- またはAgilent Technologies 54754aの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Agilent Technologies 54754aの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Agilent Technologies 54754aの取り付け説明書、サービスマニュアル、簡易説明書、またはAgilent Technologies 54754aのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Agilent Technologies 54754aの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Agilent Technologies 54754aデバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがAgilent Technologies 54754aを使用するのを助ける技術的文書のことです。説明書は通常、全てのAgilent Technologies 54754aユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Agilent Technologiesの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Agilent Technologies 54754aの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははAgilent Technologies 54754aの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Agilent Technologies 54754aに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Agilent Technologies 54754aデバイスの基本機能を使うにあたってのヒント。 Agilent Technologies 54754aのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Agilent Technologies 54754aに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるAgilent Technologies 54754aのメーカー/サービスへの連絡先に関する情報。

Agilent Technologies 54754aについてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもAgilent Technologies 54754aの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがAgilent Technologies 54754aで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)