Wilton 7060の取扱説明書

28ページ 0.44 mb
ダウンロード

ページに移動 of 28

Summary
  • Wilton 7060 - page 1

    Operating Instructions — Parts Manual 20-Inch x 20-Inch Semi Automatic Horizont al Cut-Of f Band Saw Model: 7060 WHM TOOL GROUP 2420 V antage Drive Elgin, Illinois 60124 Part No. 551 1736 Ph.: 800-274-6848 Revision A2 08/06 www .wmhtoolgroup.com Copyright © WMH T ool Group ...

  • Wilton 7060 - page 2

    ...

  • Wilton 7060 - page 3

    3 T able of Content s Cover Page ..................................................................................................................... ...... 1 General Specifications ......................................................................................................... .4 Operating Precautions .................................... ...

  • Wilton 7060 - page 4

    4 Cutting Capacity At 90 degrees 12 inches Round/12 x 35 inches Rectangle At 45 degrees 12 inches Round/12 x 12 inches Rectangle Blade Size 1 x 0.035 x 156 inches Blade Wheel Diameter 17 inches Diameter , Cast Iron Blade Speeds 82 to 262 SFPM, V ariable S peed Motor 3 H P , 3 P hase, 230/460 V olts Dimensions 87 x 31. 5 x 5 3 I nches Net Weight 1,1 ...

  • Wilton 7060 - page 5

    5 - Always follow instructions in Operating Instruc- tions and Parts Manual when changing acces- sory tools or parts. - Never modify the machine without consulting Wilton Corporation. Y ou - the Stationary Power T ool User - Hold the Key to Safety . Read and follow these simple rules for best results and full benefits from your machine. Used proper ...

  • Wilton 7060 - page 6

    6 from the work area. Make the workshop com- pletely safe by using padlocks, master switches, or by removing starter keys. Conductor Length A WG (American Wire Gauge) Number 240 V olt Lines 120 V olt Lines 0 - 50 Feet No. 14 No. 14 50 - 100 Feet No. 14 No. 12 Over 100 Feet No. 12 No. 8 Safety Instructions on Sawing Systems B C D 8. Bring adjustable ...

  • Wilton 7060 - page 7

    7 0 0 9 8 7 6 5 4 3 2 1 10 Operating Instructions Controls The operating controls for the saw are provided in a control panel on the left side of the machine. The control panel is mounted on a pivoting tube. The pivoting tube allows the operator to position the control panel in a convenient location. Introduction This manual includes operating and ...

  • Wilton 7060 - page 8

    8 ( F T ) 1 2 1 1 1 0 9 8 7 6 5 4 3 2 1 0 The bottom row of controls include the following: 1. Stop pushbutton is used to stop the saw blade drive motor . 2. Emergency stop pushbutton is used to quickly disconnect electrical power to the machine. 3. Coolant On/Off selector switch is used to start and stop the coolant pump motor . Other Controls Ref ...

  • Wilton 7060 - page 9

    9 Evaluating Cutting Efficiency Is the blade cutting efficiently? The best way to determine this is to observe the chips formed by the cutting blade. If the chip formation is powdery , then the feed rate is much too light, or the blade is dull. If the chips formed are curled, but colored — that is, either blue or straw-colored from heat generated ...

  • Wilton 7060 - page 10

    10 W ork Set-up Securing the Workpiece for Square Cuts (see figure 5) 1. Raise the saw head. 2. Slide the left vise jaw far enough to the left to allow the workpiece to be placed in the vise. 3. Place the workpiece on the work table. If the workpiece is long, provide support at the other end. It may also be necessary to provide addi- tional downwar ...

  • Wilton 7060 - page 11

    11 rod. Position the stop post against the work piece and tighten the knob in the stop L-bracket. The stop post can be moved left or right as required to place the stop post against the work piece. Figure 9: Placing workpieces in the vise ff f f f Rounds Flats/strips Channels Angles Squares/rectangles I-Beams Hexagonals T ees Knock off sharp edge h ...

  • Wilton 7060 - page 12

    12 Figure 10: Blade tracking and tensioning Blade Tracking Hex Adjustment Screws Center Locking Screws Single Adjustment Screw screws.) Factory or Field Procedure 1. Raise the saw head enough to allow the saw motor to operate. 2. Loosen four knobs securing the blade cover . Lift the cover and swing it backward. 3. Remove the blade guard mounted on ...

  • Wilton 7060 - page 13

    13 Blade Guide Bearing Adjustment Proper adjustment of the blade guide bearings is critical to efficient operation of the cut-of f saw . The blade guide bearings are adjusted at the Factory . They should rarely require adjustment. When adjustment is required, adjust immediately . Failure to maintain proper blade adjustment may cause serious blade d ...

  • Wilton 7060 - page 14

    14 T est cuts can be used to determine whether or not you have adjusted the blade accurately . Use 2-inch round bar stock to perform these test cuts, as follows: 1. With the bar stock securely clamped in the vise, make a cut through the bar stock. (See figure 14.) 2. Mark the top of the bar stock. 3. Move the bar stock about 1/4-inch past the blade ...

  • Wilton 7060 - page 15

    15 Changing Blades W ARNING: SHUT OFF ALL ELECTRICAL POWER TO THE MACHINE. 1. Loosen four knobs securing the blade cover . Lift the cover and swing it backward. 2. Remove the blade guard mounted to the left blade guide support. W ARNING: AL W A YS WEAR LEA THER GLOVES WHEN HANDLING SA W BLADE T O A VOID INJURY Servicing Hydraulic Oil W ARNING: SHUT ...

  • Wilton 7060 - page 16

    16 1. Loosen the knob on the blade guide support and slide the guide left or right as required. Repeat for the other blade guide. 2. Set the blade guide supports as required to accommodate the width/diameter of the workpiece. The blade guides should be posi- tioned so the guides do not contact the workpiece as the saw head moves downward through th ...

  • Wilton 7060 - page 17

    17 2. Remove the attaching screw , spring washer and washer . Remove and discard the brush (see figure 20). 3. Install replacement brush and secure with screw , spring washer and washer . 4. Close the blade cover and secure with four knobs. Replacement of Guide Bearings (see figure 19) 1. Remove the cap screw from the blade guide bearing. Separate ...

  • Wilton 7060 - page 18

    18 Uncrating and S potting S pot the saw where it makes the most sense for the operations you will probably be doing. If you are going to be doing cut-off work on very long pieces of stock, allow plenty of room for the stock, and the infeed and outfeed supports. Remove the saw from the shipping skid and discard any hold-down devices that were used ...

  • Wilton 7060 - page 19

    19 Wiring Diagram ...

  • Wilton 7060 - page 20

    20 T roubleshooting Fault Excessive blade breakage Premature blade dulling Bad cuts (out-of-square) Bad cuts (rough) Probable cause 1. Material loose in vise. 2. Incorrect speed or feed. 3. T eeth too coarse for material. 4. Incorrect blade tension. 5. Saw blade is in contact with workpiece before the saw is started. 6. Blade rubs on the wheel flan ...

  • Wilton 7060 - page 21

    21 1. Blade is binding in the cut. 2. Blade tension too high. 1. Blade guides worn 2. Blade guide bearings not adjusted. 3. Blade guide bearing bracket is loose. 1. Blade tooth pitch too coarse for workpiece. 2. Feed too slow; feed too fast. 3. Workpiece vibrating. 4. Gullets loading up with chips. 1. Blade tension too high. 2. Drive belt tension t ...

  • Wilton 7060 - page 22

    22 Replacement Parts This section provides exploded view illustrations that show the replacement parts for the Model 7060 12-Inch x 20-Inch Semi-Automatic Horizontal Cut-Of f Band Saw . Also provided are parts listings that provide part number and description. The item numbers shown on the illustration relate to the item number in the facing parts ...

  • Wilton 7060 - page 23

    23 Exploded View – Saw Base - Model 7060 Semi-Automatic Cut-Of f Band Saw 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 9 ...

  • Wilton 7060 - page 24

    24 Parts List – Saw Base - Model 7060 Semi-Automatic Cut-Of f Band Saw Ref Part No . Number Description Qty 1 5512120 Bolt, Hex Cap (M12X35) 1 2 5512121 W asher , Lock (M12) 1 3 5512122 Pin 2 4 5512123 Rack 1 5 5512124 Bracket, Slide 1 6 5512125 Block, Rack 1 7 5512126 Screw , Set (M6X10) 1 8 5512127 Ja w , V ise (Left ) 1 9 5512128 W asher (M12) ...

  • Wilton 7060 - page 25

    25 Part s List – Saw Base - Model 7060 Semi-Automatic Cut-Off Band Saw , (Continued) Ref Part No . Number Description Qty 120 5512222 Screw , Pan Head (M6X15) 4 121 5512223 V alve, Relief 1 122 5512224 Plate, Cover 1 123 5512225 Box, Stationary 1 124 5512226 Screw (M8X16) 4 125 5512227 Plate, Sole 1 126 5512228 Screw (1/4X5/8 In.) 2 127 5512229 B ...

  • Wilton 7060 - page 26

    26 Exploded V iew – Saw Head - Model 7060 Semi-Automatic Cut-Of f Band Saw 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 190 191 192 194 193 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 21 1 212 213 214 215 216 ...

  • Wilton 7060 - page 27

    27 Parts List – Saw Head - Model 7060 Semi-Automatic Cut-Of f Band Saw Ref Part No . Number Description Qty 146 5512248 Bearing, Thrust (51 194NJK) 1 147 5512249 Indicator , T ension 1 148 5512250 W asher , Flat 1 149 5512251 W asher , S pecial Spring 1 8 150 5512252 Bracket, Slide 1 151 5512253 W asher , Lock 3 152 5512254 Screw , Hex Cap 3 153 ...

  • Wilton 7060 - page 28

    WHM TOOL GROUP 2420 V antage Drive Elgin, Illinois 60124 Ph.: 800-274-6848 ...

メーカー Wilton カテゴリー Saw

Wilton 7060のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 7060の取扱説明書
- Wiltonの製品カード
- パンフレット
- またはWilton 7060の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Wilton 7060の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Wilton 7060の取り付け説明書、サービスマニュアル、簡易説明書、またはWilton 7060のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Wilton 7060の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Wilton 7060デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがWilton 7060を使用するのを助ける技術的文書のことです。説明書は通常、全てのWilton 7060ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Wiltonの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Wilton 7060の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははWilton 7060の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Wilton 7060に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Wilton 7060デバイスの基本機能を使うにあたってのヒント。 Wilton 7060のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Wilton 7060に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるWilton 7060のメーカー/サービスへの連絡先に関する情報。

Wilton 7060についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもWilton 7060の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがWilton 7060で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)