Edelbrock 63-0144の取扱説明書

22ページ 0.45 mb
ダウンロード

ページに移動 of 22

Summary
  • Edelbrock 63-0144 - page 1

    ©2002 Edelbrock Corporation Rev . 10/02 Brochure No. 63-0144 Catalog #70406 Thank Y ou…. …for purchasing an Edelbrock Nitrous Oxide Injection System. Nitrous Oxide injection is one of the most exciting performance enhancements, for the dollar invested, on the market today . With the use of nitrous oxide come some important safety consideration ...

  • Edelbrock 63-0144 - page 2

    Page 1 of 21 ©2002 Edelbrock Corporation Rev . 10/02 Brochure No. 63-0144 Catalog #70406 MERCUR Y MARAUDER PERFORMER EFI SERIES NITROUS SYSTEM Catalog #70406 T able of Contents Page # a. Before Y ou Install Y our Edelbrock Nitrous System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Edelbrock 63-0144 - page 3

    Page 2 of 21 ©2002 Edelbrock Corporation Rev . 10/02 Brochure No. 63-0144 Catalog #70406 Caution!! Before Y ou Install Y our Edelbrock Nitrous System… Please read this installation manual fully before installing this system. Y ou will need to have available the follo wing tools: Hand T ools ❑ Socket set including ratchets and extensions ❑ Sc ...

  • Edelbrock 63-0144 - page 4

    Page 3 of 21 ©2002 Edelbrock Corporation Rev . 10/02 Brochure No. 63-0144 Catalog #70406 WHA T IS NITROUS OXIDE? Nitrous Oxide is a cryogenic gas composed of nitrogen and oxygen molecules. It is stored as a “gas over a liquid” which means that both liquid and gaseous nitrous oxide is delivered into your engine. It is 36% oxygen by weight, whic ...

  • Edelbrock 63-0144 - page 5

    Page 4 of 21 ©2002 Edelbrock Corporation Rev . 10/02 Brochure No. 63-0144 Catalog #70406 1.0 Introduction to your Edelbrock Mercury Marauder Performer EFI Nitrous System Within the pages of this manual is information, safety tips and operation instructions for your new Edelbrock Nitrous System. Watch for these symbols to know where to go for infor ...

  • Edelbrock 63-0144 - page 6

    Page 5 of 21 ©2002 Edelbrock Corporation Rev . 10/02 Brochure No. 63-0144 Catalog #70406 1.2 Jet Map Information Edelbrock engineering has conducted dyno testing with the Edelbrock Mercur y Marauder Performer EFI system to ensure the horsepower increase the nitrous system is as intended. On a typically stock 4.6L engine, you can expect the followi ...

  • Edelbrock 63-0144 - page 7

    Page 6 of 21 ©2002 Edelbrock Corporation Rev . 10/02 Brochure No. 63-0144 Catalog #70406 QTY . DESCRIPTION Nozzle and Nozzle Hardware 1 90º Nitrous fan spray nozzle 1 Straight Nitrous fan spray nozzle 2 Nitrous fan spray nozzle bulkhead body bolt 2 Nitrous fan spray nozzle bulkhead concave nut Solenoids and Solenoid Hardware 2 Performer Nitrous s ...

  • Edelbrock 63-0144 - page 8

    Page 7 of 21 ©2002 Edelbrock Corporation Rev . 10/02 Brochure No. 63-0144 Catalog #70406 2.0 Performer System Installations 2.1 Nitrous Bottle Mounting The nitrous oxide storage cylinder is typically called a “nitrous bottle”. It is an aluminum c ylinder , designed and manufactured to withstand very high pressures. The valve on top of the bott ...

  • Edelbrock 63-0144 - page 9

    Page 8 of 21 ©2002 Edelbrock Corporation Rev . 10/02 Brochure No. 63-0144 Catalog #70406 2.2 Bottle Mounting Instructions Accurate calibration of your nitrous system depends on the bottle remaining a t a stable temperature. Choosing the proper location and orientation for your bottle can grea tly affect the overall operation of the nitrous system. ...

  • Edelbrock 63-0144 - page 10

    Page 9 of 21 ©2002 Edelbrock Corporation Rev . 10/02 Brochure No. 63-0144 Catalog #70406 2.4 Nitrous Bottle Installation After you have determined the location and orienta tion of the nitrous bottle, use the following procedure to install the bottle: 2.4.1 Street Car Installations 1. Disconnect vehicle’ s batter y . 2. Determine the location of ...

  • Edelbrock 63-0144 - page 11

    Page 10 of 21 ©2002 Edelbrock Corporation Rev . 10/02 Brochure No. 63-0144 Catalog #70406 2.5 Nitrous Feed Line Mounting 1. Determine the route your main nitrous feed line will follow . Ensure the path does not route the nitrous feed line too c lose to the exhaust system, suspension, electrical lines/components or tires. 2. Attach nitrous supply l ...

  • Edelbrock 63-0144 - page 12

    Page 11 of 21 ©2002 Edelbrock Corporation Rev . 10/02 Brochure No. 63-0144 Catalog #70406 2.6.2 Nitrous Solenoids Mounting (Continued) 7. Install solenoid assembly in desired location. 8. Leave all wiring loose for electrical systems installation . 9. Connect main nitrous feed line to inlet fitting (4AN x 1/8 NPT nitrous filter fitting) of the fir ...

  • Edelbrock 63-0144 - page 13

    Page 12 of 21 ©2002 Edelbrock Corporation Rev . 10/02 Brochure No. 63-0144 Catalog #70406 Nozzle 2 Installation (Continuation) 1. Determine nozzle mounting location in the intake boot just before the throttle body . 2. Remove the intake boot. 3. Wearing safety glasses, drill a 7/16” hole in the intake boot where nozzle placement has been determi ...

  • Edelbrock 63-0144 - page 14

    Page 13 of 21 ©2002 Edelbrock Corporation Rev . 10/02 Brochure No. 63-0144 Catalog #70406 3.1 Nitrous Electrical Components Bill of Materials (BOM) 3.2 Nomenclature Descriptions: A TO… the fuse configuration is A TO. When replacing this fuse, ask for an A TO fuse. “a”… Amperage. Important: The wiring hardware and instructions included with ...

  • Edelbrock 63-0144 - page 15

    Page 14 of 21 ©2002 Edelbrock Corporation Rev . 9/02 Batter y Fuse Relay Socket Socket Switched +12V Arming Switch Solenoid Fuel Pressure Safety Switch W ARNING! DO NOT CONNECT TO THIS TERMINAL Microswitch Red White Black BLUE Red SUPPL Y +12v ON ACC GROUND - 12 16 11 7 8 11 13 14 9 10 13 2 3 4 1 13 15 13 5 6 (2) (2) (2) Ground Ground Ground Solen ...

  • Edelbrock 63-0144 - page 16

    Page 15 of 21 ©2002 Edelbrock Corporation Rev . 10/02 Brochure No. 63-0144 Catalog #70406 3.4 Nitrous Electrical System Installation Procedures Determine the location of the Relay and Fuse Holder wire harness. Most common installa tions locate these components inside the driver’ s compartment and close to the fuse panel under the dash. Y ou can ...

  • Edelbrock 63-0144 - page 17

    Page 16 of 21 ©2002 Edelbrock Corporation Rev . 10/02 Brochure No. 63-0144 Catalog #70406 3.6 Arming Switch and Installation The arming switch is a red, lighted s witch that is a "MASTER" arming switch for your nitrous system. Without it, your nitrous system would be "on" all of the time and capable of engaging an ytime you go ...

  • Edelbrock 63-0144 - page 18

    Page 17 of 21 ©2002 Edelbrock Corporation Rev . 10/02 Brochure No. 63-0144 Catalog #70406 3.7 Microswitch Installation and Wiring (Continued) The bolts used to attach the microswitch ha ve extra length to allow for spacing the microswitch a way from the bracket if necessary . After determining the position of the micros witch, we recommend trimmin ...

  • Edelbrock 63-0144 - page 19

    Page 18 of 21 ©2002 Edelbrock Corporation Rev . 10/02 Brochure No. 63-0144 Catalog #70406 4.0 Before Y ou Run Y our V ehicle Using Y our Edelbrock Nitrous System Y ou have just completed the installa tion of your Edelbrock Nitrous System. It is time to perform some basic system checks to ensure all of the work you have done is correct and ready to ...

  • Edelbrock 63-0144 - page 20

    Page 19 of 21 ©2002 Edelbrock Corporation Rev . 10/02 Brochure No. 63-0144 Catalog #70406 5.0 T roubleshooting and Routine Maintenance How to use our T roubleshooting Flowchart: The troubleshooting of a nitrous system is basic and straightforward. The symptom chart is divided by symptom, cause and action required. Determine your problem (symptom), ...

  • Edelbrock 63-0144 - page 21

    Page 20 of 21 ©2002 Edelbrock Corporation Rev . 10/02 Brochure No. 63-0144 Catalog #70406 6. Inadequate nitrous supply . a. Weigh bottle. 1. Bottle should be 10 lbs. above empty bottle weight listed on bottle label when full. b. Check bottle pressure. 1. Maintain 900-950 psi for optimum system performance. c. Check bottle tempera ture. 1. Maintain ...

  • Edelbrock 63-0144 - page 22

    Page 21 of 21 ©2002 Edelbrock Corporation Rev . 10/02 Brochure No. 63-0144 Catalog #70406 6.0 Solenoid Inspection and Maintenance . 1. Close valve on nitrous bottle. 2. Make sure all nitrous supply lines are free of pressure before removal of any system solenoid. a. Empty main nitrous supply line at the nitrous bottle. T ake care to not brea the o ...

メーカー Edelbrock カテゴリー Automobile Parts

Edelbrock 63-0144のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 63-0144の取扱説明書
- Edelbrockの製品カード
- パンフレット
- またはEdelbrock 63-0144の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Edelbrock 63-0144の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Edelbrock 63-0144の取り付け説明書、サービスマニュアル、簡易説明書、またはEdelbrock 63-0144のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Edelbrock 63-0144の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Edelbrock 63-0144デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがEdelbrock 63-0144を使用するのを助ける技術的文書のことです。説明書は通常、全てのEdelbrock 63-0144ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Edelbrockの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Edelbrock 63-0144の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははEdelbrock 63-0144の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Edelbrock 63-0144に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Edelbrock 63-0144デバイスの基本機能を使うにあたってのヒント。 Edelbrock 63-0144のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Edelbrock 63-0144に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるEdelbrock 63-0144のメーカー/サービスへの連絡先に関する情報。

Edelbrock 63-0144についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもEdelbrock 63-0144の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがEdelbrock 63-0144で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)