-
Impex MP-PWR10.0 - page 1
NOTE: Please read all i nstructions caref ully befor e using this product Table of Contents Safety Notice Hardware Identifier Assembly Instruc tion Parts L ist Warranty Ordering Parts Model MP-PWR10.0 Retain This Manual for Reference 04-08-05 OWNER'S MANUAL MARCY PLATINUM MP-PWR 10.0 IMPEX INC. 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 ...
-
Impex MP-PWR10.0 - page 2
TA BLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICES..................................................................... 2 HARDW ARE PACK……….....…....................................................................... 3 ASSEMBLY INSTRUCTIONS.... ...
-
Impex MP-PWR10.0 - page 3
IMPORTANT SAFETY NOTICE PRECA UTIONS This exerci se machine is bui lt for optimum safety. How ever , certain precauti ons apply whenev er you operate a piece of exer cise equi pment. Be sure to read the entir e manual before you assemble or operate your machine. In particul ar, note the follow ing safety precautions: 1. Keep children and pets away ...
-
Impex MP-PWR10.0 - page 4
HA RDWA RE PA CK 3 ...
-
Impex MP-PWR10.0 - page 5
HA RDWA RE PA CK 4 ...
-
Impex MP-PWR10.0 - page 6
HA RDWA RE PA CK 5 ...
-
Impex MP-PWR10.0 - page 7
A SSEMBLY INSTRUCTION Tools Required A ssembling the Machine: Tw o Adj ustable Wrenches and A llen Wrenches NOTE: It is strongly recommended this machine be assembled by tw o or more people to avoid possible inj ury. STEP 1 (See Diagram 1) A.) Attach the Main Fram e (#27) to the Bench Front & Rear Stabilizers (#28 & 29). Secure each end wit ...
-
Impex MP-PWR10.0 - page 8
STEP 2 (See Diagram 2) A.) Attach the two side-holes on bottom of Backrest Supports ( #30) to the piv ot on the Main Frame (#27). Secur e it w ith one M12 x 5 ¾” Al len Bolt (#75) , two Ø 1” W ashers (#68), and one M12 Airc raft Nut (#71). B.) Align the piv ot on top of Backrest Incline Support (#31) to the middle side-holes in betw een the B ...
-
Impex MP-PWR10.0 - page 9
STEP 3 (See Diagram 3) A.) Attach the Leg Developer (#33) to the open bracket on the M ain Frame (#27) . Secure it with one M 10 x 3 1/8” Allen Bolt ( #76), tw o Ø ¾” W ashers (#69), and one M10 Ai rcraft Nut (#72). D o not over ti ghten the bolt and nut, make sur e Leg Dev eloper is able to swiv el. B.) Insert the U-shaped Pin (#39) into the ...
-
Impex MP-PWR10.0 - page 10
STEP 4 (See Diagram 4) A.) Attach the Arm Curl Pad (#37) to the Ar m Curl Stand ( #32). Secure it with tw o M8 x ¾” Allen Bolts ( #84) and tw o ∅ ¾” W ashers (#70). Insert the Arm C url Stand into the front opening on the Mai n Frame (#27) and secure it w ith a Lock Knob (#61) to hold it at the desired heig ht. B.) Remove the Arm Curl when ...
-
Impex MP-PWR10.0 - page 11
STEP 5 (See Diagram 5) A.) Note: Do not tig hten the Nuts and Bolts until i nstructed to do so. B.) Attach the top of Left Support (#2) to an Uprig ht Beam (#1). Secur e it wi th two M 10 x 5/8” Allen Bolts ( #82) and Ø ¾” W ashers (#69). C.) Attach the Left Floor Stabilizer (#4) to the Uprig h t Beam . Secure it with one M10 x 4” Carri age ...
-
Impex MP-PWR10.0 - page 12
STEP 6 (See Diagram 6) A.) Attach the Rear Vertical Fr ame (#9) onto the Rear Base (#8). Secure i t wi th two M 10 x 2 ½” Carri age Bolts ( #74), Ø ¾” W a shers (#69), and M10 Aircr aft Nuts (#72). B.) Attach the Rear Base (#8) and Front Vertical Frame (#10) to the Rear Stabilizer (#7). Align the hol es and secure them together wi th two M 1 ...
-
Impex MP-PWR10.0 - page 13
DIAGRAM 6 12 ...
-
Impex MP-PWR10.0 - page 14
CABLE LOOP DIAGRAM 13 ...
-
Impex MP-PWR10.0 - page 15
STEP 7 (See Diagram 7 & Cable Loop Diagram) A.) Attach the 113 7/8” Upper Cable (#24) to the front opening on the U pper Frame (#11) . Make sure the ball stopper of the Cable is underneath the Fr ame. B.) Attach a Pulley (#45) to the openi ng. Secure i t wi th one M10 x 2 ½” All en Bolt (#77) , two 5/8” Pulley Bushings ( #65), and one M1 ...
-
Impex MP-PWR10.0 - page 16
STEP 8 (See Diagram 8 & Cable Loop Diagram) A.) Attach the 58 1/8” Low er Cable ( #25) to the low er opening on the bottom of Front Vertical Frame (#10). Attach a Pul ley ( #45) to the opening and secure it w ith one M10 x 2 3/8” Allen Bolt ( #78), tw o ½” Pull ey Bushi ngs (#66) , and one M10 Airc raft Nut (#72). B.) Pull the Cabl e und ...
-
Impex MP-PWR10.0 - page 17
STEP 9 (See Diagram 9) A.) Attach a W eight Post (#20) to the Rig ht Support (#3). Secure it w ith a M10 x ¾” Al len Bolt (#81) and Ø ¾” W asher (#69). Slide an Oly m pic Sleeve (#44) onto the Post. Repeat the same procedure to instal l the other side. B.) Insert the Left & Rig ht Bar Catches (#15 & 16) , Left & Right Safety Catc ...
-
Impex MP-PWR10.0 - page 18
17 ...
-
Impex MP-PWR10.0 - page 19
RACK EXPLODED DIAGRAM 18 ...
-
Impex MP-PWR10.0 - page 20
PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Uprig ht Beam 2 51 1 ¾” Sq uare End Cap 5 2 Left Suppor t 1 52 2” Squar e End Cap 2 3 Right Suppor t 1 53 Ø ½” Bushing 2 4 Left Floor St abilizer 1 54 1” Squar e End Cap 2 5 Right Floor St abilizer 1 55 Ø 1” End Cap 1 6 Cross Brace 1 56 Foam Roll End Cap 6 7 Rear Stabilizer 1 57 2” x 1 ¾” S ...
-
Impex MP-PWR10.0 - page 21
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ( "IMPEX") warrants this produc t to be fr ee from def ects in work m anship and m ater ial, under norm al use and service conditions, for a period of two y ear s on the Fram e from the date of purc hase. T his warranty extends only to the original purc haser. IMPEX 's obligation under this W ar ...
Impex MP-PWR10.0についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもImpex MP-PWR10.0の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがImpex MP-PWR10.0で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。