Aquacal H100の取扱説明書

36ページ 1.46 mb
ダウンロード

ページに移動 of 36

Summary
  • Aquacal H100 - page 1

    POO L & SPA HEAT PUMP O WNER’S MANUAL H e a t W a v e A e r o T e m p H 1 0 0 A T 1 0 0 H 1 2 0 A T 1 2 0 N O T E : T H I S M A N U A L A L S O A P P L I E S T O X L 1 0 0 , X L 1 2 0 , S B 1 2 0 , & A P S 1 2 0 M O D E L S ...

  • Aquacal H100 - page 2

    2 Owner Note s ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ___________________ ...

  • Aquacal H100 - page 3

    3 Table of Contents WELCOME TO THE AQUACA L FAMILY ..................... ........... ............ ........... 4 IMPORTANT FEATURES OF YOUR NEW HEAT PUMP ........... ............ ......4 GENERAL SAFETY INFORMA TION ........... ............ ........... ............ ........... .......5 WATER CHEM I STRY & TEMPERATURE FACTOR S .................... ...

  • Aquacal H100 - page 4

    4 WELCOME TO THE AQUACAL FAM ILY Congratulations on your wise decision to make an AquaCal heat pump part of your home. Since 1981, AquaCal has m aint ained the worldwide lead in the manufacture of swimm ing pool & spa heat pumps. Your new heat pump is not only a great investment, but also the m ost cost effective method available for heating po ...

  • Aquacal H100 - page 5

    5 GENERAL SAF ETY INFORM ATION Used and maintained properly, y our heat pump will provide year-upon-year of safe and economical service. However, as wi th any mechanical or electrical device, to get the most from your heat pump– while i nsuring personal safety for you and others –certain operational and maintenance fact ors must be observed. Li ...

  • Aquacal H100 - page 6

    6 WATER C HEMI STRY & TE MPE RATURE FACT ORS Water Temperature Safety Factors Water Chemistry Safety Factors RECOMMENDED CH EMISTRY WATE R STANDARDS Chlorine…………… …: 1.0 – 3.0 ppm in pools , 1.5 – 3.0 ppm in spas Bromine…………… …: 2.0 – 4.0 ppm in pools , 3.0 – 5.0 ppm in spas PH……………… …….: 7.4 – ...

  • Aquacal H100 - page 7

    7 HOW A HEAT PUMP WO RKS T HE FOLLO WING E XPLANA TION IS P ROVIDED T O HEL P YOU I N UNDERSTA NDING WHAT TO EXPECT FROM YO UR HE AT PUMP … A Heat Pump Does Not Make Heat… Heat pumps are so extraordinarily efficient because they do not need to produce heat in order to warm pool or spa water. R ather, heat pumps sim ply transfer heat from the ou ...

  • Aquacal H100 - page 8

    8 GETTING F AMILIAR WITH CONTROLS DIGITAL CONT ROLLER – PAN EL L AYOUT Control Buttons ( AS INDICATED BY CIRCLED LETTERS ) A. Down Arrow – Pressing th is key decreases the temperature setting. Setting the temperature below 60°F turns the heat pump off. B. Pool / Spa Selector – Pressing this key selects either the pool or spa m ode. Also used ...

  • Aquacal H100 - page 9

    9 DIGITAL CONT ROLLER - OPER ATIONAL DIS PLAYS T HE FOLLOWING CODES WI LL BE DISPLAYED AS PART OF THE NORMAL OPERATI ON OF THE HEATER : OPERATIONAL CODES o FLO —No water flow detected. Code message will appear any time the circulating pump is off, or when the hea ter is not receiving correct water flow. o OFF —Syste m is off. Sy stem is off unt ...

  • Aquacal H100 - page 10

    10 GETTING YO UR HEAT P UMP STARTED & STOPP ED ATTENTION: THIS IS A QUICK-START GUIDE …For m ore complete information concerning the digital controller features a nd programm ing, see: Owner’s Instructions for HP7 Digital Heat Pump Controller, locate d in the appendix of this manual. INITIAL START UP 1. Start the water circulator pum p. NOT ...

  • Aquacal H100 - page 11

    11 GETTING YOUR HEAT PUMP STARTED & STOPPED (Continued) 8. In operation, whenever the actual (display ed) water temperature falls below the desired set point, the unit will start heat ing after an initial time delay of 3-4 minutes. NOTE: T HE HEA T PUMP INCORPORA TES AN ANTI - SHOR T CYCLE TIME DELAY . S HOULD OPERATION BE INTERRUPTED , RESTAR ...

  • Aquacal H100 - page 12

    12 MAINTENAN CE PLANNE D MAI NTENANCE PROG RAM AquaCal offers a very reasonably priced, profess ionally-performed, Planned Maintenance Program ….See APPENDIX for full details. GENERAL MAI NTENANCE o You should have your heat pum p inspected and maintained on an annual basis by a qualified pool heat pump specialist. Additionally, if your heat pump ...

  • Aquacal H100 - page 13

    13 MAINTAI NING PROPER WATE R FLOW o It is important to operate and m aintain your filter according to the m anufacturer’s specifications. As a filter gets dirty, the water flow to the heat pump is reduced. The higher the pressure on the filter gauge, the lower t he flow rate. o Similar to a dirty filter, large am ounts of debris in the pump bask ...

  • Aquacal H100 - page 14

    14 Recommended Clearances… Sides, Front, and Rear 12-I NCHES (R EAR ) 24-I NCHES ( SIDE ) 24-I NCHES ( SIDE ) 30-I NCHES ( FRONT ) ...

  • Aquacal H100 - page 15

    15 Recommended Clearances… Overh ead, Front, & Rear: RAIN RUN - OFF MUST BE DIRECTED AWAY FROM UNIT . OVERHANG WI TH GUTTER 30” M INIMUM C LEARANCE , F RONT 1 F T . MINIMUM C LEARANCE , R EAR 5 FT . MINIMUM CLEARANCE , O VERHEAD No Scale ...

  • Aquacal H100 - page 16

    16 SEASONAL USE & SHUT DOW N DURING T HE SW IM SEAS ON o During the swim season, even if the pool or spa is not in use, al low water to flow through the heater. o This eliminates the need to repositi on valves when you do wish to heat your pool or spa. FREEZE P ROTE CTION / E XTEND ED SHUT DO WNS o In areas where freezing conditions are a ra re ...

  • Aquacal H100 - page 17

    17 Winterizing (Cont inued) 5. Permit all of the water to drain out of the condenser and then, threading clockwise, replace the plug finger-tight. 6. Reinstall the heater front cover and secure w ith attaching screws previously removed. 7. To prevent insects and verm in from entering the plum bing during the winterized period, partially reconnect t ...

  • Aquacal H100 - page 18

    18 Winterizing (Conti nued) To Winterize a Heat Pump Equipp ed with an External Drain (Per Figure-3) 1. Disconnect all electrical power to the heat er; turn OFF circulating pump. 2. At the two (2) connection unions, disc onnect the plumbing to the heater (removal is counter-clockwise). 3. Locate the drain plug at lower, right-hand, front corner of ...

  • Aquacal H100 - page 19

    19 TROUBLESH OOTING HEAT PUM P NOT RUNNIN G o Is the display lit? If not, ensure the m ain breaker (located at the power supply panel) and the disconnect switch (located ne ar the heat pump) are both turned ON. o Doe s the display read “Flo”? If so , check to be sure that the circulating pump is operating and the filter is clean. There m a y al ...

  • Aquacal H100 - page 20

    20 WATER LE AKI NG OUT O F TH E HEAT PUM P (Is it a leak or just condensation from normal oper ation? Here’s how to find out). o Sh ut off your heat pum p, leaving the pool pump running. In a couple of hours there should be a marked reduction in the a mount of water around the bottom of the heat pump. o Or, as an alternate m ethod to check for a ...

  • Aquacal H100 - page 21

    21 APPENDIX I. AQUACAL’S PLANNE D MAINTENANCE PROGRAM II. CALCULATING INIT IAL HEATING TIME III. OWNER’S INS TRUCTIONS FOR H P7 DIGITAL HEAT PUMP CONT ROLLER ...

  • Aquacal H100 - page 22

    PLANNE D MAI NTENANCE PROG RAM Just as you would have yearly service performed on your air conditioning system, regular inspection & m aintenance of your AquaCal heat pump will insure highest operating efficiencie s while also protecting your investment… Potentially extending the useful life o f your heat pump far beyond the warranty period. ...

  • Aquacal H100 - page 23

    CALCULAT ING REQUIRE D HE ATING TIM E The initial time it takes to get your pool warm depends on several factors. First you will need to determ i ne ho w m any gallons of water are in your pool. If y ou know this, you can com pute the pounds of water in the pool and the BTU’s necessary to heat the pool to the desired tem perature. Secondly, you n ...

  • Aquacal H100 - page 24

    When you start up your new AquaCal Heat Pump for the fir st time to heat your pool, you must allow the unit to run continuously unti l the desired temperature is reached. This may take from several hours to several days depending upon the tim e of the year and the outside conditions. If y ou utilize a time clock or similar device to control the ope ...

  • Aquacal H100 - page 25

                                           ? ...

  • Aquacal H100 - page 26

    2 TABLE of CONTENTS GENERA L DESCRIPTION OF HP7 CONTROL LER ............................................................................... 3 HP7 CONTROLLER SPECIFICATIONS .................................................................................................... 3 I NPUTS : ................................................................. ...

  • Aquacal H100 - page 27

    3 GENERAL DE SCRIPTION of HP7 CONTRO LLER The HP7 is a powerful microproc essor control designed for use in swim ming pool & spa heat pumps. The control features 3-di git temperature and set point di spla y, with programming changes easil y performed by simple 3-ke y operation. The HP7 offers precise water tempe rature control, accurate de fros ...

  • Aquacal H100 - page 28

    4 CO NTROL PANEL LAYOUT (App earance will va ry between model lin es) ...

  • Aquacal H100 - page 29

    5 START UP & SETTING OPERATING CO NTROLS 1. Applying Power to The Controller: A. W hen power is first applied, the control pe rforms a lamp test and the displ ay will read [888]. Additionall y, all status LED’s lights will illum inate for 4 seconds and then go o ff for 1 second. B. The control will then displ ay the actual temperature as lon ...

  • Aquacal H100 - page 30

    6 5. Changing The Pool Te mperature Set Point: A. Usi ng the Pool / Spa ke y, select the POOL temperature set poin t. The pool set poi nt indicator light will confirm your selection b y lig hting. B. The pool temperature set point range is adjustable from 6 0 ° F. to 95 ° F (104 ° F in latest models) . using the Up     or Down  ? ...

  • Aquacal H100 - page 31

    7 Selecting ULC Option (Con tinued): 4) With [ULC] displayed, pressing either the Up o r Down arrow ke y will display either (1) or (0). Selecting (0) will allow the control keypad to remain unl ocked. Selecting (1) will enable the User Lock Cod e option. Then, to enter a lock code number, press the pool/spa key once. [E LC] (Enter Lock Code) wi ll ...

  • Aquacal H100 - page 32

    8 Selecting Call / Flex Pump Options [C FO] … ( This feature will apply only if the heater installation includes a C all/Flex module.) : A. Depress both t he Up     and Down     arrow keys simultaneousl y until [CF1] display appears. Depress the poo l/spa key twice, the displ ay will appear. B. With the [CFO] (Call Flex Op ...

  • Aquacal H100 - page 33

    9 OWNER TROUBL ESHOOTING Owner Troub leshooting Procedure: Note… This procedure is restricted to problems which may be related to t he control s ystem of your heater, and/or site conditions affecting th e ability of the control s ystem to properly start and run your heater. For other suspected problems , such as (but not li mited to): “Heater L ...

  • Aquacal H100 - page 34

    10 Sequence of O peration PU MP OFF POW ER ON ______________________ "FLO" D ispl ayed PUMP ON POW ER ON ______________________ W at er Temp. D ispl ayed SE T POINT BE LOW 60º F ______________________ Heater is "OFF" Pressin g Up-Dow n Keys W ill Display "OFF", W ater Tem p. Displayed SE T POINT ABOVE 60ºF __________ ...

  • Aquacal H100 - page 35

    11 CONTACTING the FACTORY… Should you ever exp erience problems with your h eater, or if you simply desire further information a bout your heater’s operation, our Customer Support staff stands ready to assist. Please call us toll-free at: 1-800-786-7751. We Sincerely Appreciate Your Business…. Thank you for choosing AQUACAL for your swimming ...

  • Aquacal H100 - page 36

    12     2737 24 th Street North St. Petersburg, FL 3371 3 800-786-7751 www.aquacal.com ...

メーカー Aquacal カテゴリー Heat Pump

Aquacal H100のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- H100の取扱説明書
- Aquacalの製品カード
- パンフレット
- またはAquacal H100の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Aquacal H100の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Aquacal H100の取り付け説明書、サービスマニュアル、簡易説明書、またはAquacal H100のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Aquacal H100の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Aquacal H100デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがAquacal H100を使用するのを助ける技術的文書のことです。説明書は通常、全てのAquacal H100ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Aquacalの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Aquacal H100の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははAquacal H100の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Aquacal H100に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Aquacal H100デバイスの基本機能を使うにあたってのヒント。 Aquacal H100のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Aquacal H100に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるAquacal H100のメーカー/サービスへの連絡先に関する情報。

Aquacal H100についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもAquacal H100の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがAquacal H100で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)