-
Audiovox AXT-500 - page 1
OWNER'S MANUAL Model AXT -500 500 Watt 4-Channel Bridgeable MOSFET Amplifier ...
-
Audiovox AXT-500 - page 2
Specifications.....................................................................3 Precautions........................................................................ 4 Installation Instructions...................................................... 5 Wiring Instructions........................................................ 6 - 7 4-Channel and M ...
-
Audiovox AXT-500 - page 3
Input Impedance: Low-Level 10K Ohms High-Level 100 Ohms Input Sensitivity: Low-Level 200 mV - 8 V. High-Level 2V - 10 V Filter type: Selectable Full/Low-pass Crossover @ 12dB/Octave Filter Crossover: LPF 50-250 Hz (variable) Supply Voltage: 12 volts, negative ground Fuse Rating: 30 amps. Dimensions (W X H X D): 295 mm X 54.3 mm X 230 mm 11-5/8" ...
-
Audiovox AXT-500 - page 4
1. Although this unit is designed with built-in self-protection circuits, there may be a possibility of damage if it is not wired correctly. Please follow the wiring instructions carefully for the type of system being used. 2. The last lead to be connected is the wire to the positive( ) terminal of the battery. Connect this wire only after having c ...
-
Audiovox AXT-500 - page 5
1. Select a mounting area where the amplifier will have sufficient air circulation for proper cooling. Inadequate air circulation will cause the temperature of the amplifier to rise and will trigger the thermal protection mode. 2. Place the amplifier on the mounting surface and mark the locations of the four mounting holes as shown in the illustrat ...
-
Audiovox AXT-500 - page 6
The wiring of your amplifier will depend on the system and speakers you are using but will either be a stereo, mono, or mixed-mono application. The following pages illustrate the input and output wiring for these types. please refer to the appropriate diagrams for the system configuration you are using. The power and speakers wire connections for t ...
-
Audiovox AXT-500 - page 7
4. Speaker Connections Depending on the type and number of speakers used with the amplifier , wire them to the speaker terminals as per the appropriate wiring diagram. For most applications, #16 gauge wire should be used for the speaker leads but in no case thinner than #18 gauge. For leads in excess of 10 feet, #14 gauge is recommended. When wirin ...
-
Audiovox AXT-500 - page 8
-8- CAR STEREO Right Rear+ HIGH-LEVEL (SPEAKER) OUTPUTS USE EITHER HIGH-LEVEL OR LOW-LEVEL INPUT , NOT BOTH. IMPORT ANT GND GND 2CH 2CH 1CH 1CH 3CH 3CH 4CH 4CH X-OVER X-OVER 50Hz 50Hz 250Hz 250Hz 250Hz 250Hz MIN MIN MAX MAX LPF LPF 50Hz 50Hz LPF LPF GAIN GAIN MIN MIN MAX MAX GAIN GAIN LPF LPF FULL FULL X-OVER X-OVER HI-INPUT HI-INPUT LPF LPF FULL F ...
-
Audiovox AXT-500 - page 9
-9- CAR STEREO GROUND BA TTERY FOR 12 VOL T USE ONL Y AUTO-ANTENNA LEAD GROUND MET AL SECTION OF VEHICLE EXISTING SCREW OR BOL T CLEAN P AINT , RUST , DIRT OR GREASE FROM AREA FOR GOOD CONNECTION. LEFT FRONT SPEAKER REM BATT GND BRIDGED BRIDGED BRIDGED BRIDGED CH1 CH2 CH3 CH4 FUSE FUSE LEFT REAR SPEAKER RIGHT REAR SPEAKER LEFT SPEAKER RIGHT SPEAKER ...
-
Audiovox AXT-500 - page 10
-10- CAR STEREO Right Rear+ HIGH-LEVEL (SPEAKER) OUTPUTS USE EITHER HIGH-LEVEL OR LOW-LEVEL INPUT , NOT BOTH. IMPORT ANT GND GND 2CH 2CH 1CH 1CH 3CH 3CH 4CH 4CH X-OVER X-OVER 50Hz 50Hz 250Hz 250Hz 250Hz 250Hz MIN MIN MAX MAX LPF LPF 50Hz 50Hz LPF LPF GAIN GAIN MIN MIN MAX MAX GAIN GAIN LPF LPF FULL FULL X-OVER X-OVER HI-INPUT HI-INPUT LPF LPF FULL ...
-
Audiovox AXT-500 - page 11
-11- CAR STEREO GROUND BA TTERY FOR 12 VOL T USE ONL Y AUTO-ANTENNA LEAD GROUND MET AL SECTION OF VEHICLE EXISTING SCREW OR BOL T CLEAN P AINT , RUST , DIRT OR GREASE FROM AREA FOR GOOD CONNECTION. LEFT FRONT SPEAKER REM BATT GND BRIDGED BRIDGED BRIDGED BRIDGED CH1 CH2 CH3 CH4 FUSE FUSE LEFT FRONT SPEAKER RIGHT FRONT SPEAKER MONO SPEAKER OR SUB-WOO ...
-
Audiovox AXT-500 - page 12
-12- CAR STEREO Right Rear+ HIGH-LEVEL (SPEAKER) OUTPUTS USE EITHER HIGH-LEVEL OR LOW-LEVEL INPUT , NOT BOTH. IMPORT ANT GND GND 2CH 2CH 1CH 1CH 3CH 3CH 4CH 4CH X-OVER X-OVER 50Hz 50Hz 250Hz 250Hz 250Hz 250Hz MIN MIN MAX MAX LPF LPF 50Hz 50Hz LPF LPF GAIN GAIN MIN MIN MAX MAX GAIN GAIN LPF LPF FULL FULL X-OVER X-OVER HI-INPUT HI-INPUT LPF LPF FULL ...
-
Audiovox AXT-500 - page 13
-13- CAR STEREO GROUND BA TTERY FOR 12 VOL T USE ONL Y AUTO-ANTENNA LEAD GROUND MET AL SECTION OF VEHICLE EXISTING SCREW OR BOL T CLEAN P AINT , RUST , DIRT OR GREASE FROM AREA FOR GOOD CONNECTION. REM BATT GND BRIDGED BRIDGED BRIDGED BRIDGED CH1 CH2 CH3 CH4 FUSE FUSE LEFT SPEAKER OR SUB-W OOFER 4-8 OHMS RIGHT SPEAKER OR SUB-W OOFER 4-8 OHMS 2-CHAN ...
-
Audiovox AXT-500 - page 14
-14- Power Indicator Lamps After initial set-up, the amplifier should not require any further adjustment unless there is a change in the car stereo or speaker system with which it is used. If activated by a rise in emperature, the unit will resume operation after cooling of f to a normal operating range. If activated by an overload condition, the s ...
-
Audiovox AXT-500 - page 15
LPF Crossover Frequency Control This Control selects the crossover frequency when the Sub woofer Crossover Selector is in the "LPF" setting. Adjust it to the appropriate position for the characteristics and crossover frequency requirements of the speaker system with which the amplifier is being used. 5 4 from the system. If, however , the ...
-
Audiovox AXT-500 - page 16
AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 90 days from the date of original purchase, such defect(s) will be repaired or replaced with new or reconditioned product (a ...
-
Audiovox AXT-500 - page 17
2003 Audiovox Electronics Corporation, Hauppauge, N.Y . C C Printed in Korea 128-6561 1 ...
Audiovox AXT-500についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもAudiovox AXT-500の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがAudiovox AXT-500で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。